Home › Vehicle Exterior › BODY PANEL › FRONT SIDE MEMBER
BM37A0E _01 Vehicle Exterior _087817 BODY PANEL _0419584 FRONT SIDE MEMBER F

BODY PANEL  FRONT SIDE MEMBER  ASSEMBLY REPLACEMENT  


K156358

With the front fender apron assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Remove the A.

K156164N01
1.635,1.792 1,0.583 1,0.583 0.833,0.583 false 0.677,0.479 0.833,0.677 0.156,0.198 10 false A


c.

Remove the A.

K156165N01
1.167,3.5 1.333,3.5 1.333,3.5 1.75,2.76 false 1,3.406 1.313,3.563 0.313,0.156 10 false A


d.

Remove the front side member assembly.

K156166C01
1.167,2.167 1.333,2.167 1.333,2.167 1.563,1.656 false 1,2.073 1.313,2.229 0.313,0.156 10 false *1
*1 FRONT SIDE MEMBER ASSEMBLY - -




INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure to attach correctly in accordance with the body dimension diagram as this part affects the front wheel alignment.


c.

Weld the front side member assembly to the vehicle side.

K156168C01
1.667,0.75 1.833,0.75 1.833,0.75 2.052,1.24 false 1.51,0.646 1.823,0.802 0.313,0.156 10 false *1
*1 FRONT SIDE MEMBER ASSEMBLY - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa or 780 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K156169C01
0.271,0.427 0.583,0.583 0.313,0.156 10 false *A 3.625,0.417 3.938,0.573 0.313,0.156 10 false *B
*A LH *B RH
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




d.

Remove A from the new parts.

K156167C01
3.917,3.083 3.75,3.083 3.75,3.083 3.448,2.5 false 3.417,1.479 3.75,1.25 3.75,1.25 3.917,1.25 false 3.99,2.979 4.302,3.135 0.313,0.156 10 false *1 3.99,1.156 4.146,1.354 0.156,0.198 10 false A
*1 FRONT SIDE MEMBER REINFORCEMENT SUB-ASSEMBLY - -



e.

Weld the A to the vehicle side.

K156170C01
1.417,3.5 1.583,3.5 1.583,3.5 1.99,2.844 false 1.26,3.396 1.573,3.552 0.313,0.156 10 false A
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Weld the A to the vehicle side.

K156171N01
0.75,0.583 0.917,0.583 0.917,0.583 1.625,1.823 false 0.604,0.49 0.76,0.688 0.156,0.198 10 false A


g.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


h.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.