Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM37A0E _01 Vehicle Exterior _087817 BODY PANEL _0419587 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K156344

With the cowl top side upper panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K156045C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the side member assembly.

K156046C01
1.177,4.677 1.427,4.677 1.427,4.677 2.104,4.021 false 0.99,4.594 1.302,4.75 0.313,0.156 10 false *1 2.833,2.5 3.146,2.656 0.313,0.156 10 false *a
*1 SIDE MEMBER ASSEMBLY - -
*a 30 mm (1.18 in.) - -


K156047

K156048


d.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K156049C01
0,0 0,0 false
K108837

Adhesive - -



e.

Remove the A.

K156050N01
2.99,4.104 2.698,4.104 2.698,4.104 2.333,3.531 false 3.052,4.01 3.208,4.208 0.156,0.198 10 false A


f.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K156051C01
1.135,3.01 1.375,3.01 1.375,3.01 1.74,2.677 false 0.969,2.927 1.281,3.083 0.313,0.156 10 false *1
*1 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K156049C01
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the A to the vehicle side.

K156052N01
2.156,2.302 2.698,1.823 2.698,1.823 2.99,1.823 false 3.052,1.729 3.208,1.927 0.156,0.198 10 false A

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K156053


g.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K156054C01
0,0 0,0 false
K108837

Adhesive - -



h.

Weld the side member assembly.

K156055C01
1.177,5.094 1.469,5.094 1.469,5.094 2.135,4.208 false 1.01,5.021 1.323,5.177 0.313,0.156 10 false *1
*1 SIDE MEMBER ASSEMBLY - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 780 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K156056

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 780 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




i.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


j.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.