Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL
BM37A0E _01 Vehicle Exterior _087817 BODY PANEL _0419592 ROCKER PANEL F

BODY PANEL  ROCKER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K156350

With the front body pillar cut and join replacement sections (pattern 1) and quarter panel cut and join replacement sections (small areas) removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K156099C01
0,0 0,0 false
K108837

Adhesive - -



c.

Remove the rear body panel front outside.

K156100C01
4.49,4.5 4.302,4.5 4.302,4.5 4.083,4.104 false 4.563,4.427 4.875,4.583 0.313,0.156 10 false *1
*1 REAR BODY PANEL FRONT OUTSIDE - -


K156101

K156102C01
2.417,0.979 2.729,1.135 0.313,0.156 10 false *a 5.146,1.188 5.458,1.344 0.313,0.156 10 false *b
*a 90 mm (3.54 in.) *b 50 mm (1.97 in.)



d.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K156103C01
0,0 0,0 false
K108837

Adhesive - -



e.

Remove the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer.

K156104C01
2.708,5.208 2.927,5.208 2.927,5.208 3.323,4.188 false 2.573,3.354 2.75,3.354 2.75,3.354 3,3.688 false 2.396,3.271 2.708,3.427 0.313,0.156 10 false *1 2.51,5.115 2.823,5.271 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY *2 ROCKER PANEL SUB-ASSEMBLY OUTER


K156105


f.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K156106C01
5.042,3.198 4.802,3.198 4.802,3.198 4.396,3.417 false 5.104,3.125 5.417,3.281 0.313,0.156 10 false *1 2.156,2.99 2.469,3.146 0.313,0.156 10 false *a
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -
*a 140 mm (5.51 in.) - -



d.

Before temporarily installing the new parts, weld the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer with the standard number of welding points.

K156107C01
3.271,0.854 3.073,0.229 3.073,0.229 2.875,0.229 false 4.813,1.49 5.125,1.865 5.125,1.865 5.375,1.865 false 2.688,0.146 3,0.302 0.313,0.156 10 false *1 5.427,1.781 5.74,1.938 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY *2 ROCKER PANEL SUB-ASSEMBLY OUTER



e.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K156108C01
0,0 0,0 false
K108837

Adhesive - -



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K156343


g.

Weld the center body pillar reinforcement sub-assembly and rocker panel sub-assembly outer to the vehicle side.

K156109C01
2.708,5.208 2.927,5.208 2.927,5.208 3.323,4.188 false 2.573,3.354 2.75,3.354 2.75,3.354 3,3.688 false 2.396,3.271 2.708,3.427 0.313,0.156 10 false *1 2.51,5.115 2.823,5.271 0.313,0.156 10 false *2
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY *2 ROCKER PANEL SUB-ASSEMBLY OUTER
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 1180 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K156110C01
2.177,1.833 2.49,1.99 0.313,0.156 10 false *a 4.938,1.823 5.25,1.979 0.313,0.156 10 false *a
*a 24 mm (0.94 in.) - -



h.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K156111C01
0,0 0,0 false
K108837

Adhesive - -



i.

Weld the rear body panel front outside to the vehicle side.

K156112C01
2.875,4.583 3.104,4.583 3.104,4.583 3.313,4.135 false 2.688,4.49 3,4.646 0.313,0.156 10 false *1
*1 REAR BODY PANEL FRONT OUTSIDE - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 1180 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



K156113


j.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


k.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


l.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.