With the quarter panel assembly removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Remove Weld Points |
|
Remove Weld Points |
|
Cut with Disc Sander etc. |
|
Cut and Join Location |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | LH | - | - |
|
Adhesive | - | - |
Remove the A.
| *A | LH | - | - |
Remove the quarter panel reinforcement extension.
| *A | LH | - | - |
| *1 | QUARTER PANEL REINFORCEMENT EXTENSION | - | - |
Remove the roof side panel outer.
| *A | LH | - | - |
| *1 | ROOF SIDE PANEL OUTER | - | - |
| *a | 200 mm (7.87 in.) | - | - |
A is reused.
| *A | LH | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | LH | - | - |
|
Adhesive | - | - |
Remove the quarter wheel house panel sub-assembly outer.
| *A | LH | - | - |
| *1 | QUARTER WHEEL HOUSE PANEL SUB-ASSEMBLY OUTER | - | - |
| *A | LH | - | - |
| *A | LH | *B | PATTERN 1 |
| *C | PATTERN 2 | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | RH | - | - |
|
Adhesive | - | - |
Remove the A.
| *A | RH | - | - |
Remove the quarter panel reinforcement extension.
| *A | RH | - | - |
| *1 | QUARTER PANEL REINFORCEMENT EXTENSION | - | - |
Remove the roof side panel outer.
| *A | RH | - | - |
| *1 | ROOF SIDE PANEL OUTER | - | - |
| *a | 200 mm (7.87 in.) | - | - |
A is reused.
| *A | RH | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | RH | - | - |
|
Adhesive | - | - |
Remove the quarter wheel house panel sub-assembly outer.
| *A | RH | - | - |
| *1 | QUARTER WHEEL HOUSE PANEL SUB-ASSEMBLY OUTER | - | - |
| *A | RH | - | - |
| *A | RH | *B | PATTERN 1 |
| *C | PATTERN 2 | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Spot Weld |
|
Plug Weld |
|
Plug Weld |
|
Plug Weld |
|
Fillet Weld |
|
Butt Weld |
|
Body Sealer |
|
Assembly Mark |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | LH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | LH | - | - |
|
Adhesive | - | - |
Weld the quarter wheel house panel sub-assembly outer to the vehicle side.
| *A | LH | - | - |
| *1 | QUARTER WHEEL HOUSE PANEL SUB-ASSEMBLY OUTER | - | - |
| *A | LH | - | - |
| *A | LH | *B | PATTERN 1 |
| *C | PATTERN 2 | - | - |
| *a | 15 mm (0.59 in.) | - | - |
Weld the A to the vehicle side.
| *A | LH | - | - |
| *a | 20 mm (0.79 in.) | - | - |
Weld the roof side panel outer to the vehicle side.
| *A | LH | - | - |
| *1 | ROOF SIDE PANEL OUTER | - | - |
Weld the quarter panel reinforcement extension to the vehicle side.
| *A | LH | - | - |
| *1 | QUARTER PANEL REINFORCEMENT EXTENSION | - | - |
Remove A from the new parts.
| *A | LH | - | - |
| *1 | ROCKER PANEL SUB-ASSEMBLY OUTER | - | - |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | LH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | LH | - | - |
|
Adhesive | - | - |
Weld the A to the vehicle side.
| *A | LH | - | - |
For positioning of the new parts, align the installation standard holes of the outer panel and the inner panel.
| *A | RH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | RH | - | - |
|
Adhesive | - | - |
Weld the quarter wheel house panel sub-assembly outer to the vehicle side.
| *A | RH | - | - |
| *1 | QUARTER WHEEL HOUSE PANEL SUB-ASSEMBLY OUTER | - | - |
| *A | RH | - | - |
| *A | RH | *B | PATTERN 1 |
| *C | PATTERN 2 | - | - |
| *a | 15 mm (0.59 in.) | - | - |
Weld the A to the vehicle side.
| *A | RH | - | - |
| *a | 20 mm (0.79 in.) | - | - |
Weld the roof side panel outer to the vehicle side.
| *A | RH | - | - |
| *1 | ROOF SIDE PANEL OUTER | - | - |
Weld the quarter panel reinforcement extension to the vehicle side.
| *A | RH | - | - |
| *1 | QUARTER PANEL REINFORCEMENT EXTENSION | - | - |
Remove A from the new parts.
| *A | RH | - | - |
| *1 | ROCKER PANEL SUB-ASSEMBLY OUTER | - | - |
Before installing a new part, apply body sealer.
Apply body sealer in an even, continuous bead.
| *A | RH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | RH | - | - |
|
Adhesive | - | - |
Weld the A to the vehicle side.
| *A | RH | - | - |
After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.