Home › Vehicle Exterior › BODY PANEL › ROOF PANEL (for Sliding roof)
BM37A0E _01 Vehicle Exterior _087817 BODY PANEL _0419609 ROOF PANEL(for Sliding roof) F

BODY PANEL  ROOF PANEL(for Sliding roof)  ASSEMBLY REPLACEMENT  


K155850

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points

a.

If reusing the roof panel reinforcement, trim the hemming location using a disc sander, etc.


b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K155851C01
3.792,6.469 3.938,6.469 3.938,6.469 4.073,6.146 false 3.625,6.365 3.938,6.521 0.313,0.156 10 false *a
*a Disc Sander - -
K108837

Adhesive - -


K155852



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Before temporarily installing the new parts, apply body sealer and adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115) to the roof panel reinforcement No.2, roof panel reinforcement No.3, roof panel reinforcement No.4, roof panel reinforcement No.5 and roof panel reinforcement No.6.

HINT:

Apply enough body sealer and adhesive to the panels.


K155853C01
2.125,0.302 2.292,0.302 2.292,0.302 2.448,0.74 false 3.323,0.313 3.49,0.313 3.49,0.313 3.615,0.656 false 3.958,0.313 4.125,0.313 4.125,0.313 4.323,0.667 false 4.802,0.313 4.969,0.313 4.969,0.313 5.094,0.688 false 5.479,0.302 5.646,0.302 5.646,0.302 5.792,0.688 false 1.969,0.208 2.281,0.365 0.313,0.156 10 false *1 3.167,0.208 3.479,0.365 0.313,0.156 10 false *2 3.792,0.219 4.104,0.375 0.313,0.156 10 false *3 4.646,0.219 4.958,0.375 0.313,0.156 10 false *4 5.323,0.208 5.635,0.365 0.313,0.156 10 false *5
*1 ROOF PANEL REINFORCEMENT NO.2 *2 ROOF PANEL REINFORCEMENT NO.3
*3 ROOF PANEL REINFORCEMENT NO.4 *4 ROOF PANEL REINFORCEMENT NO.5
*5 ROOF PANEL REINFORCEMENT NO.6 - -
K108837

Adhesive - -



d.

Before temporarily installing the new parts, weld the roof panel, roof panel reinforcement No.2, roof panel reinforcement No.3, roof panel reinforcement No.4, roof panel reinforcement No.5 and roof panel reinforcement No.6 with the standard number of welding points.


e.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


K155854C01
1.292,4.365 1.469,4.083 1.469,4.083 1.604,4.083 false 0.625,4.094 0.76,4.094 0.76,4.094 0.927,4.281 false 0.26,5.375 0.396,5.375 0.396,5.375 0.656,5.135 false 0.75,1.729 0.885,1.729 0.885,1.729 1.198,1.99 false 2.333,1.167 2.208,0.677 2.208,0.677 2.073,0.677 false 3.479,1.135 3.281,0.76 3.281,0.76 3.135,0.76 false 4.177,1.135 4.01,0.75 4.01,0.75 3.875,0.75 false 4.958,1.115 4.813,0.802 4.813,0.802 4.698,0.802 false 5.646,1.125 5.5,0.833 5.5,0.833 5.385,0.833 false 0.583,1.635 0.896,1.792 0.313,0.156 10 false *1 1.906,0.573 2.219,0.729 0.313,0.156 10 false *2 2.979,0.667 3.292,0.823 0.313,0.156 10 false *3 3.719,0.656 4.031,0.813 0.313,0.156 10 false *4 4.542,0.698 4.854,0.854 0.313,0.156 10 false *5 5.219,0.729 5.531,0.885 0.313,0.156 10 false *6 0.115,5.271 0.427,5.427 0.313,0.156 10 false *a 0.469,3.99 0.781,4.146 0.313,0.156 10 false *b 1.604,3.969 1.917,4.125 0.313,0.156 10 false *c
*1 ROOF PANEL *2 ROOF PANEL REINFORCEMENT NO.2
*3 ROOF PANEL REINFORCEMENT NO.3 *4 ROOF PANEL REINFORCEMENT NO.4
*5 ROOF PANEL REINFORCEMENT NO.5 *6 ROOF PANEL REINFORCEMENT NO.6
*a Wooden Hammer *b Dolly
*c Cloth Tape - -



f.

Before temporarily installing the new parts, apply body sealer to the windshield header panel sub-assembly and back door opening frame sub-assembly.

HINT:

Apply enough body sealer to the panels.


K155855C01
0.438,3.333 0.604,3.333 0.604,3.333 0.833,2.896 false 6.479,4.365 6.313,4.365 6.313,4.365 5.844,3.385 false 0.271,3.24 0.583,3.396 0.313,0.156 10 false *1 6.531,4.26 6.844,4.417 0.313,0.156 10 false *2
*1 WINDSHIELD HEADER PANEL SUB-ASSEMBLY *2 BACK DOOR OPENING FRAME SUB-ASSEMBLY


K155856C01
0.74,6.396 1.906,6.646 1.167,0.25 0.375,1.417 1.542,1.667 1.167,0.25 1.906,6.531 2.073,6.531 2.073,6.531 2.073,5.969 false 1.542,1.542 2.479,1.542 2.479,1.542 2.479,1.375 false 0.781,6.438 1.958,6.667 1.177,0.229 10 false 7.5 (76, 66 in.*lbf) 0.427,1.448 1.604,1.677 1.177,0.229 10 false 7.5 (76, 66 in.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -


K155857


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


j.

Measure the dimensions before installing the roof panel.

K155858N01
6.104,1.844 6.26,2.042 0.156,0.198 10 true A 0.844,1.74 1,1.938 0.156,0.198 10 true B 5.844,1.563 6,1.76 0.156,0.198 10 true C 4.833,2.542 4.99,2.74 0.156,0.198 10 true D 4.146,2.458 4.302,2.656 0.156,0.198 10 true E 3.563,2.531 3.719,2.729 0.156,0.198 10 true F 2.615,2.042 2.771,2.24 0.156,0.198 10 true G 5.854,2.125 6.01,2.323 0.156,0.198 10 true H 4.875,1.125 5.031,1.323 0.156,0.198 10 true I 4.167,1.146 4.323,1.344 0.156,0.198 10 true J 3.458,1.073 3.615,1.271 0.156,0.198 10 true K 2.635,1.573 2.792,1.771 0.156,0.198 10 true L



Reference Value:
Area Measurement Area Measurement
A 800 mm (31.50 in.) B 715 mm (28.15 in.)
C 900 mm (35.43 in.) D 1058 mm (41.65 in.)
E 1276 mm (50.24 in.) F 1551 mm (61.06 in.)
G 2444 mm (96.22 in.) H 878 mm (34.57 in.)
I 1036 mm (40.79 in.) J 1279 mm (50.35 in.)
K 1531 mm (60.28 in.) L 2433 mm (95.79 in.)