Home › Vehicle Exterior › BODY PANEL › BACK DOOR
BM37A0E _01 Vehicle Exterior _087817 BODY PANEL _0419611 BACK DOOR F

BODY PANEL  BACK DOOR  PAINT REPAIR  


STRUCTURE


K156428C01
2.365,0.281 2.448,0.125 2.448,0.125 2.552,0.125 false 0.458,1.958 0.563,1.958 0.563,1.958 0.656,1.865 false 0.865,0.823 0.979,0.719 0.979,0.719 1.073,0.719 false 2.417,1 2.99,1.51 2.99,1.51 3.083,1.51 false 2.594,0.042 2.906,0.198 0.313,0.156 10 false *1 1.104,0.625 1.417,0.781 0.313,0.156 10 false *2 3.125,1.427 3.354,1.604 0.229,0.177 10 false *3 0.302,1.875 0.615,2.031 0.313,0.156 10 false *1
*1 OUTER PANEL
*2 INNER PANEL
*3 Glass adhesive line


Material Notes
OUTER PANEL TSOP Body color (painted) Adhesion (not decomposable)
INNER PANEL PPGF Substrate color (unpainted)


SUPPLY PARTS SPECIFICATION


K156429C01
2.677,0.323 2.74,0.167 2.74,0.167 2.854,0.167 false 0.875,0.74 0.979,0.823 0.979,0.823 1.063,0.823 false 2.927,2.042 2.823,2.042 2.823,2.042 2.781,1.865 false 2.896,0.094 3.208,0.25 0.313,0.156 10 false *1 1.104,0.75 1.417,0.906 0.313,0.156 10 false *2 2.979,1.969 3.292,2.125 0.313,0.156 10 false *1
*1 OUTER PANEL
*2 INNER PANEL


The same top coat paint (excluding the color base) as the new car is painted on the outer panel (including the glass adhesive line).The reason is to ensure the adhesion quality of the glass.


<Surface treatment structure>
Clear
Primer
Substrate

NOTICE:

TSOP is a material with poor adhesive quality. As a result, the glass adhesive line on the outer panel becomes unusable when the substrate is exposed.



POINTS TO CONSIDER WHEN PERFORMING BODY REPAIRS AND PAINTING


Replace the assembly in the following cases
·

The glass adhesive line on the substrate is exposed.

·

The inner panel is damaged.


Assembly replacement (supply part) Spot repair
Body repair - Be careful not to damage the glass adhesive line on the outer panel.

Assembly replacement (supply part) Spot repair
Masking
<Illustration 1>
·

Make sure to apply masking tape to the glass adhesive line to prevent paint from sticking and ensure the glass adhesive quality. (a-a,b-b)

·

The inner panel is unpainted. Therefore, make sure to properly apply masking tape to prevent paint from contacting the inner panel. Pay special attention to the edges. (c-c)



<Illustration 1>

K156430C01
5.646,2.615 5.552,2.135 5.552,2.135 5.427,2.135 false 5.25,3.125 5.375,3.125 5.375,3.125 5.635,2.875 false 5.854,2.958 6.094,3.156 6.094,3.156 6.188,3.156 false 4.198,3.156 4.083,3.156 4.083,3.156 3.948,2.865 false 1.49,2.26 1.604,2.26 1.604,2.26 1.729,2.469 false 1.365,3.094 1.479,3.094 1.479,3.094 1.646,2.854 false 2.167,2.979 2.417,2.781 2.417,2.781 2.49,2.781 false 2.052,3.292 2.083,3.01 false 2.167,3.292 2.052,3.292 2.052,3.292 1.698,2.677 false 3.052,3.073 3.156,3.073 3.156,3.073 3.385,2.875 false 3.156,2.802 3.333,2.344 false 3.021,2.802 3.135,2.802 3.135,2.802 3.563,2.625 false 3.094,2 3.229,2 3.229,2 3.406,2.25 false 1.333,2.188 1.646,2.344 0.313,0.156 10 false *1 1.198,3.021 1.51,3.177 0.313,0.156 10 false *2 2.521,2.708 2.833,2.865 0.313,0.156 10 false *3 3.646,2.177 3.958,2.333 0.313,0.156 10 false *b 2.219,3.219 2.531,3.375 0.313,0.156 10 false *c 2.052,2.531 2.365,2.688 0.313,0.156 10 false *a 2.854,2.729 3.167,2.885 0.313,0.156 10 false *c 2.906,1.917 3.219,2.073 0.313,0.156 10 false *3 4.26,3.083 4.573,3.24 0.313,0.156 10 false *1 2.896,3 3.208,3.156 0.313,0.156 10 false *2 5.104,3.063 5.417,3.219 0.313,0.156 10 false *3 5.271,2.052 5.583,2.208 0.313,0.156 10 false *2 6.24,3.083 6.552,3.24 0.313,0.156 10 false *1
*1 OUTER PANEL *2 INNER PANEL
*3 MASKING TAPE - -
*a 25 mm (0.98 in.)
(Distance between the scribed lines)
*b 18 mm (0.71 in.)
(Distance between the scribed lines)
*c Scribed Line - -



Assembly replacement (supply part) Spot repair
Painting and drying
<Illustration 2>
Back door condition Work method Drying temperature
Single - Secure it in the same position and condition as when it is installed on the vehicle, and support it so that the load is not concentrated in one area. (A)
NOTICE:

Take care when removing the glass as it is easily deformed.


HINT:

Support the panel at the hinge on the upper part of the panel and a secure location on the lower part of the panel.


80°C or less
On-vehicle Fully closed None (B)
Half open Remove the left and right damper stays and secure them with the supports. (C)
Install the left and right damper stays and secure them with the supports. (D)
NOTICE:
·

The back door may twist due to the force of the damper stay. Therefore, do not perform work with only one damper stay removed.

·

Do not perform work with the glass removed as the back door may deform.



Fully open Remove the left and right damper stays and secure them with the supports. (E)
Left and right damper stays installed. (F)
NOTICE:
·

The back door may twist due to the force of the damper stay. Therefore, do not perform work with only one damper stay removed.

·

Do not perform work with the glass removed as the back door may deform.




<Illustration 2>

K147752N01
0.167,0.083 7,2.083 6.833,2 0.25,0.135 0.708,0.333 0.458,0.198 10 false (A) 0.083,2.167 0.542,2.365 0.458,0.198 10 false (B) 2.375,2.167 2.833,2.365 0.458,0.198 10 false (C) 4.667,2.167 5.125,2.365 0.458,0.198 10 false (D) 2.417,3.917 2.875,4.115 0.458,0.198 10 false (F) 0.083,3.917 0.542,4.115 0.458,0.198 10 false (E)