Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL SYSTEM
NM37A0E _51 Engine / Hybrid System _086671 A25A-FXS, A25B-FXS FUEL _0415623 FUEL SYSTEM CO CONTROL F

A25A-FXS, A25B-FXS FUEL  FUEL SYSTEM  CONTROL  D-4S SYSTEM  


FUNCTION OF MAIN COMPONENTS


a.

The D-4S system has the following components and functions:

Component Function
Fuel Pump (for Low Pressure Side) Sends fuel (300 to 530 kPa) from the fuel tank assembly to the fuel pump assembly (for high pressure side) and port fuel injector assembly.
Fuel Pump Assembly (for High Pressure Side) Increases the pressure of the fuel from the fuel pump (for low pressure side) to a pressure of 3.0 to 25 MPa and sends it to the fuel delivery pipe (for high pressure side).
Spill Control Valve (Built-in Fuel Pump Assembly (for High Pressure Side)) Closes and opens the fuel flow path to the high-pressure fuel system in accordance with signals from the ECM.
Fuel Pressure Pulsation Damper (Built-in Fuel Pump Assembly (for High Pressure Side)) Reduces fuel pressure fluctuation (pulsation) and noise.
Fuel Delivery Pipe Sub-assembly (for Low Pressure Side) Delivers the low-pressure fuel to the port fuel injector assembly.
Fuel Delivery Pipe (for High Pressure Side) Delivers the high-pressure fuel to the direct fuel injector assembly.
Fuel Pressure Sensor Senses the fuel pressure and outputs a signal to the ECM.
Port Fuel Injector Assembly Injects a calculated (by the ECM) quantity of 300 to 530 kPa (low pressure) fuel into the intake port.
Direct Fuel Injector Assembly Injects a calculated (by the ECM) quantity of 3.0 to 25 MPa (high pressure) fuel directly into the combustion chamber.
ECM Depending on the vehicle condition, and based on signals from various sensors, the ECM calculates the optimal injection timing and volume, and controls the direct fuel injector assembly and fuel pump assembly (for high pressure side).



FUNCTION


a.

The Direct injection 4-stroke gasoline engine Superior version (D-4S) system has both direct type fuel injection, which directly injects high-pressure fuel into the combustion chamber, and port type fuel injection, which injects fuel into the intake port. The system optimally controls the fuel injectors for direct injection and port injection according to engine load.


b.

In low to medium engine load ranges, both direct type and port type fuel injections are used together or one of them is used to create homogeneous mixed air, thus contributing to stable combustions. With this, the system achieves low fuel consumption and low emissions. In addition, in high engine load ranges, only the direct type fuel injection is used to cool down the intake air with the chilling effect of vapors in the fuel which is injected into the cylinder, improving charging efficiency and anti-knock properties.


c.

Immediately after the engine is started in cold state, the port fuel injector assembly on the port side is selected for the injection aiming at homogenizing the mixture in the combustion chamber. Next, the direct fuel injector assembly on the cylinder injection side performs fuel injection during the compression process in order to stratify the mixture layers around the spark plug. This formation not only enables a substantial retardation of ignition timing but also raises the in exhaust gas temperature, which facilitates the warm-up of the catalyst following a cold start.


d.

A high-pressure 6-hole nozzle injector is used as the direct fuel injector assembly. The fuel atomized by this injector widely spreads from the 6 holes when injected into the combustion chamber while avoiding interference with the valve and combining with a large volume of intake air. High-pressure atomized spray spreads into the combustion chamber under its own energy without depending on air flow which promotes uniform and effective mixing with the intake air, contributing to ideal combustion in all driving conditions.

W135857C01
1.5,1.292 2.479,1.292 true 1.51,2.115 2.323,2.115 true 1.323,1.208 1.635,1.365 0.313,0.156 10 false *1 1.333,2.021 1.646,2.177 0.313,0.156 10 false *2
*1 Port Fuel Injector Assembly *2 Direct Fuel Injector Assembly


Fuel Injector System Activation Ranges
W136137E01
1.833,3.083 2.083,3.083 2.083,3.083 2.5,2.667 true 5.083,1.583 5.583,0.917 5.583,0.917 5.75,0.917 true 2.771,1.875 4.667,2.104 1.896,0.229 10 false Direct Injection + Port Injection 5.802,0.823 6.771,1.031 0.969,0.208 10 false Direct Injection 0.969,2.979 1.792,3.188 0.823,0.208 10 false Port Injection 0.51,1.906 1.573,2.135 1.063,0.229 10 false Engine Load (%) 3.042,3.198 4.313,3.448 1.271,0.25 10 false Engine Speed (rpm) 2.427,2.865 2.792,3.073 0.365,0.208 10 false 1000 3.49,2.865 3.854,3.073 0.365,0.208 10 false 2800 4.667,2.875 5.031,3.083 0.365,0.208 10 false 4800 1.771,1.49 1.969,1.667 0.198,0.177 10 false 70 1.771,1.677 1.969,1.854 0.198,0.177 10 false 60 1.781,2.302 1.979,2.479 0.198,0.177 10 false 25