Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
NM37A0E _59 Vehicle Exterior _087238 WINDOW / GLASS _0417542 POWER WINDOW CONTROL SYSTEM CO CONTROL F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  CONTROL  POWER WINDOW CONTROL  


SYSTEM CONTROL


a.

The power window control system has the following functions:

Function Outline

*: The function setting can be changed using customized body electronics system.

Power Up-and-down This function causes the window to open or close while the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is being pulled halfway up or pushed halfway down. The window stops as soon as the switch is released.
One-touch Auto Up-and-down The one-touch auto up-and-down function enables the window to be fully opened or closed at a touch of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly.
Jam Protection The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during one-touch auto-up operation or power up operation.
Catch Protection Catch protection function automatically stops the power window if a foreign object gets jammed in the window during one-touch auto-down operation or power down.
Remote Control The multiplex network master switch assembly can control the up-and-down operation of the windows.
Window Lock
·

Disables operation of the 3 passenger windows using each power window regulator switch assembly when the window lock switch is on.

·

Even when the window lock switch is on, the 3 passenger windows can be operated using the multiplex network master switch assembly.


Key Off Operation
·

Makes it possible to operate the power windows for approximately 45 seconds after the ignition switch is turned off, if either front door is not opened.

·

If the window lock switch is off, the windows can be operated using the power window regulator switch assembly or any of the rear power window regulator switch assemblies. If the window lock switch is on, only the multiplex network master switch assembly can be used to operate the windows.


Key-linked Up-and-down* When the electrical key transmitter sub-assembly is not in the interior detection area, the driver door is locked, and the mechanical key in the driver door is turned and maintained in the lock direction for 1.5 seconds or more, the main body ECU (multiplex network body ECU) activates the power window motors to raise all door windows while the mechanical key is turned. Similarly, when the driver door is unlocked, turning and maintaining the driver door key cylinder in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered.
Transmitter-linked Up-and-down* When the lock button is pressed and held for longer than 3 seconds, the main body ECU (multiplex network body ECU) activates the power window motors in accordance with the signal to raise all of the door windows. Similarly, when the unlock button is pressed and held for longer than 3 seconds, the main body ECU (multiplex network body ECU) activates the power window motors in accordance with the signal to lower all of the door windows.
Power Window Glass Open Warning When the ignition switch is turned from ON to off and the driver door is opened with the power window glass open, the multi buzzer in the combination meter assembly sounds once. Then, a warning message appears on the multi-information display.
Customization The on or off setting of some functions can be performed using the GTS. For details, refer to the Repair Manual.

HINT:

The ECU built into each power window motor stores the initial position of its door window glass. The initial position is not cleared even if the terminals, fuses or the power window motor connector are disconnected. However, after removing or reinstalling window components, or replacing the power window regulator switch assembly or power window regulator motor assembly, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.



b.

Jam Protection Function

i.

A jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window glass during one-touch auto up operation and power up operation.


ii.

The operation of the jam protection function is described below:

Operation Function
During auto up operation (except remote operation) Down operation of 125 mm (4.9 in.) or 2.5 seconds
During manual up operation Down operation of 45 mm (1.8 in.) or 2.5 seconds



c.

Catch Protection Function

i.

A catch protection function automatically stops the power window if a foreign object gets caught in the door window during one-touch auto down operation and power down operation.



d.

Power Window Regulator Motor Assembly

i.

The magnet and Hall IC in the power window regulator motor assembly are used to enable power window jam protection.

Y245047C04
2.781,1.552 3.042,0.885 3.042,0.885 3.208,0.885 true 1.906,1.604 1.479,2.25 1.479,2.25 1.313,2.25 true 1.885,1.25 1.167,0.5 1.167,0.5 1,0.5 true 5.354,2.073 5.771,2.073 true 5.938,1.115 6.354,0.448 6.354,0.448 6.521,0.448 true 0.813,0.427 1.125,0.583 0.313,0.156 10 false *1 3.271,0.802 3.583,0.958 0.313,0.156 10 false *2 1.125,2.177 1.438,2.333 0.313,0.156 10 false *3 5.354,1.156 5.667,1.313 0.313,0.156 10 false *2 5.063,0.885 5.219,1.083 0.156,0.198 10 false S 5.667,1.438 5.813,1.625 0.146,0.188 10 false S 5.677,0.875 5.802,1.063 0.125,0.188 10 false N 5.063,1.438 5.188,1.625 0.125,0.188 10 false N 5.802,2 6.146,2.281 0.344,0.281 10 false *1 6.594,0.375 6.906,0.531 0.313,0.156 10 false *3
*1 Hall IC *2 Worm Gear
*3 Magnet - -



ii.

The power window ECU detects the amount of door glass movement by counting pulse signal 1 sent from the pulse sensor (Hall IC). The power window ECU also detects the direction of the door glass movement using 2 types of signals: pulse signal 1 and pulse signal 2, which have different phases. The power window ECU controls each function according to the data about the door glass position obtained from the 2 pulse signals.

Y180993E01
1.583,0.563 2.615,0.927 1.031,0.365 10 false Pulse Signal 1 1.604,1.948 2.635,2.313 1.031,0.365 10 false Pulse Signal 1 1.625,2.708 2.656,3.073 1.031,0.365 10 false Pulse Signal 2 3.25,3.25 4.542,3.656 1.292,0.406 10 false Door Glass Down 5.615,3.292 6.698,3.656 1.083,0.365 10 false Door Glass Up 2.938,1.01 4.844,1.417 1.906,0.406 10 false Time for 1 Motor Revolution 0.063,0.458 1.438,1.042 1.375,0.583 10 false Door Glass Movement Amount Detection 0.063,2.26 1.458,2.865 1.396,0.604 10 false Door Glass Movement Direction Detection 2.74,0.292 2.948,0.531 0.208,0.24 10 false HI 2.729,0.646 3,0.927 0.271,0.281 10 false LO 2.76,1.823 2.969,2.063 0.208,0.24 10 false HI 2.75,2.198 3.01,2.479 0.26,0.281 10 false LO 2.771,2.625 2.979,2.865 0.208,0.24 10 false HI 2.75,2.99 2.979,3.26 0.229,0.271 10 false LO 5.094,1.813 5.302,2.052 0.208,0.24 10 false HI 5.073,2.208 5.281,2.448 0.208,0.24 10 false LO 5.063,2.625 5.271,2.865 0.208,0.24 10 false HI 5.083,2.979 5.323,3.25 0.24,0.271 10 false LO


iii.

The power window ECU detects changes in the motor rotation speed using pulse signal 1. As a result, the power window ECU detects the load applied to the door glass and controls the jam protection and catch protection.

Y146733E02
0.333,1.688 1.708,2.156 1.375,0.469 10 false Door Glass Movement Speed Detection 2.042,0.813 3.417,1.281 1.375,0.469 10 false Pulse Signal 1 2.042,2.406 3.417,2.875 1.375,0.469 10 false Pulse Signal 1 3.104,1.031 3.583,1.406 0.479,0.375 10 false LO 3.104,0.656 3.583,1.031 0.479,0.375 10 false HI 3.104,2.25 3.583,2.625 0.479,0.375 10 false HI 3.104,2.625 3.583,3 0.479,0.375 10 false LO 3.625,1.51 4.167,1.865 0.542,0.354 10 false Normal 4.417,3.104 4.958,3.458 0.542,0.354 10 false Jammed




FAIL-SAFE


a.

If a Hall IC in the power window motor malfunctions, some power window functions will be prohibited in fail-safe mode:

i.

Each power window only operates when the corresponding power window regulator switch is fully pushed down or pulled up and held in that position.


ii.

When any power window ECU detects an abnormality in a Hall IC, which detects the position, speed and direction of the window, it switches to fail-safe mode:




DIAGNOSIS


a.

If a power window ECU detects a malfunction in the power window control system, a Diagnostic Trouble Code (DTC) is stored in memory.

i.

The DTCs can be read using the GTS. For details, refer to the Repair Manual.