Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for HV Model) › 2020.02–2020.11
NM37A0E _54 Brake _086687 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0418462 BRAKE CONTROL SYSTEM(for HV Model) CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for HV Model)  CONTROL  BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with pre-collision system

*2: 4WD/AWD models

Brake Booster with Master Cylinder Assembly No. 1 Skid Control ECU Calculates the optimal brake force based on the brake pedal stroke and No. 2 skid control ECU commands and sends signals to the brake actuator.
Brake Actuator Based on the signals received from the No. 1 skid control ECU, controls the brake fluid pressure in the brake fluid circuits and brake fluid pressure in the wheel cylinders.
Solenoid Relay Built into the No. 1 skid control ECU and supplies power to the solenoid valves.
Motor Relay Built into the No. 1 skid control ECU and supplies power to the pump motor.
Accumulator Pressure Sensor (Pacc) Detects the accumulator brake fluid pressure and is used to control the pump motor.
Stroke Simulator Pressure Sensor (Prct) Detects the brake fluid pressure in the stroke simulator which is generated by the depression of the brake pedal by the driver.
Servo Pressure Sensor (Psrv) Detects the fluid pressure of the servo chamber.
Gap Hold Valve (SGH)
·

During normal control, transmits the brake fluid pressure generated by the depression of the brake pedal by the driver to the stroke simulator.


·

During a malfunction, isolates the brake fluid pressure of the gap hold chamber.


Stroke Simulator Generates a natural brake pedal feel in response to depression of the brake pedal by the driver.
Stroke Simulator Cut Valve (SSA) Allows the stroke simulator pressure to flow to the brake master cylinder reservoir assembly such as when the system is malfunctioning.
Linear Solenoid Valve (SLA, SLR) Based on commands from the No. 1 skid control ECU, outputs regulated brake fluid pressure to the servo chamber.
Regulator
·

Supplies pressurized brake fluid which is controlled by the linear solenoid valves to the servo chamber when the No. 1 skid control ECU is operating.


·

Supplies brake fluid pressure from the accumulator to the servo chamber when the No. 1 skid control ECU is not operating or during back-up when the No. 1 skid control ECU is malfunctioning.


Master Cylinder Generates brake fluid pressure in accordance with the depression amount of the brake pedal.
Relief Valve Opens to prevent excess pressure created by the brake booster with accumulator pump assembly.
Brake Master Cylinder Reservoir Assembly Brake Fluid Level Warning Switch Detects when the brake fluid level is low.
Brake Booster with Accumulator Pump Assembly Pump Motor Pumps the brake fluid from the brake master cylinder reservoir assembly to the accumulator.
Accumulator Accumulates brake fluid supplied by the pump motor under pressure.
Brake Actuator Assembly No. 2 Skid Control ECU
·

Determines the condition of the vehicle based on signals from each sensor, and sends control signals to the No. 1 skid control ECU and brake actuator.


·

Performs regenerative cooperative braking by communicating with each ECU.


Brake Actuator Controls the brake fluid pressure in the brake fluid circuits and brake fluid pressure in the wheel cylinders based on the brake control signals sent from the No. 2 skid control ECU.
Pump Motor Pumps brake fluid from the master cylinder or brake fluid reservoir.
Linear Solenoid Valve (SM1, SM2) Regulates brake fluid pressure supplied from the pump motor.
Pressure Holding Solenoid Valve,Pressure Reduction Solenoid Valve Independently controls the brake fluid pressure of the 4 wheels when ABS, TRC, VSC, etc. is operating.
Master Cylinder Pressure Sensor (Pmc) Built into the brake actuator and detects the master cylinder pressure.
Wheel Cylinder Pressure Sensor (Pwc) Detects the brake fluid pressure in the wheel cylinder.
Solenoid Relay Built into the No. 2 skid control ECU and supplies power to the solenoid valves.
Motor Relay Built into the No. 2 skid control ECU and supplies power to the pump motor.
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Airbag Sensor Assembly*1 Sends a brake control request signal to the No. 2 skid control ECU when a collision is detected.
Yawrate Sensor
·

The yawrate sensor incorporates the yawrate sensor and acceleration sensor.

·

The yawrate sensor detects the vehicle's yaw rate.

·

The acceleration sensor detects the vehicle's longitudinal and lateral deceleration.

·

The yawrate sensor sends the detection signals from the yawrate sensor and acceleration sensor to the No. 2 skid control ECU via CAN communication.


Steering Sensor Detects the steering direction and angle of the steering wheel.
Stop Light Switch Assembly Used for the illumination of the stop lights.
VSC OFF Switch Disables TRC and VSC functions when pressed.
Pattern Select Switch*2 Switches the Trail Mode on and off.
Electric Parking Brake Switch Assembly Brake Hold Switch Switches the brake hold function on and off.
Brake Pedal Stroke Sensor Assembly Detects the stroke distance of the brake pedal.
Front Door Courtesy Light Switch Assembly (LH) Outputs whether the driver door is open or closed to the No. 1 skid control ECU.
Hybrid Vehicle Control ECU Controls the regenerative braking force via communication with the No. 2 skid control ECU during regenerative cooperative braking. Also, controls drive force when TRC or VSC is operating.
Inverter with Converter Assembly MG ECU Sends information regarding the motor to the No. 2 skid control ECU during regenerative cooperative braking.
ECM Controls the engine output based on signals received from the hybrid vehicle control ECU.
Rack and Pinion Power Steering Gear Assembly Power Steering ECU Receives the signal of steering torque assist request from the No. 2 skid control ECU.
Combination Meter Assembly Each of the lights and buzzers inform the driver of system operations, malfunctions, or control restriction conditions. Also, messages are displayed on the multi-information display in response to system abnormalities and system malfunction.
Forward Recognition Camera*1 Sends brake request signals to the No. 2 skid control ECU.
Network Gateway ECU Relays data between buses.


FAIL-SAFE


a.

If a malfunction is detected in the brake system, the fail-safe function operates. Depending on the type of malfunction, the fail-safe function informs the driver via warning indicators in the combination meter assembly and continues brake control via the use of non-malfunctioning parts. Also, when the system is not operating, the fluid pressure generated in the brake master cylinder by the depression of the brake pedal works as a back-up mechanism to ensure braking force.



DIAGNOSIS


a.

A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to the Repair Manual.