Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Gasoline Model) › 2020.02–2020.11
NM37A0E _54 Brake _086687 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0418463 BRAKE CONTROL SYSTEM(for Gasoline Model) CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Gasoline Model)  CONTROL  BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with pre-collision system

Brake Actuator Assembly Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor and switch, and sends the brake control signals to the brake actuator assembly.
Solenoid Valves
·

The hydraulic circuit has 2 master cylinder cut solenoid valves, 4 pressure holding solenoid valves and 4 pressure reduction solenoid valves.

·

Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.


Pump Motor Drives the pumps inside the brake actuator assembly.
Solenoid Relay (Built into Skid Control ECU) Supplies power to the solenoid valves.
Motor Relay (Built into Skid Control ECU) Supplies power to the pump motor.
Master Cylinder Pressure Sensor Built into the brake actuator assembly, detects the master cylinder pressure.
Brake Master Cylinder Reservoir Sub-assembly Brake Fluid Level Warning Switch Detects the brake fluid level.
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Airbag Sensor Assembly Yawrate Sensor
·

The airbag sensor assembly incorporates the yawrate sensor and acceleration sensor.

·

The yawrate sensor detects the vehicle's yaw rate.

·

The acceleration sensor detects the vehicle's longitudinal and lateral deceleration.

·

The airbag sensor assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via CAN communication.

·

Sends a brake control request signal to the skid control ECU when a collision is detected.*


Acceleration Sensor
Steering Sensor Detects the steering direction and angle of the steering wheel.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Brake Pedal Load Sensing Switch Detects the depression angle of the brake pedal.
VSC OFF Switch Disables TRC and VSC functions when pressed.
Electric Parking Brake Switch Assembly Brake Hold Switch Switches the brake hold function on and off.
ECM
·

Sends the throttle position signal, accelerator pedal position signal and engine speed signal to the skid control ECU.

·

Based on the signals from the skid control ECU, controls the engine output.


Rack and Pinion Power Steering Gear Assembly Power Steering ECU Receives the signal of steering torque assist request from the skid control ECU.
Combination Meter Assembly Each of the lights and buzzers inform the driver of system operations, malfunctions, or control restriction conditions. Also, messages are displayed on the multi-information display in response to system abnormalities and system malfunction.
Forward Recognition Camera* Sends brake request signals to the skid control ECU.
Network Gateway ECU Relays data between buses.
4WD ECU Assembly Controls the distribution of drive force based on signals received from the skid control ECU when the VSC system is operating.
Downhill Assist Control Switch Allows the driver to turn downhill assist control on and off.
No. 1 Pattern Select Switch Assembly MUD & SAND Switch Selects the "MUD & SAND" multi-terrain select mode.
ROCK & DIRT Switch Selects the "ROCK & DIRT" multi-terrain select mode.


FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator assembly, the system continues performing brake control by excluding the excluding the malfunctioning area and using only the areas that are operating normally.



DIAGNOSIS


a.

A diagnosis function is provided in consideration of serviceability in order to simplify the inspection of systems. For details of the diagnosis function, refer to the Repair Manual.