Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM (for Gasoline Model) › 2020.02–2020.11
NM37A0E _54 Brake _086687 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0418463 BRAKE CONTROL SYSTEM(for Gasoline Model) DE DETAILS F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM(for Gasoline Model)  DETAILS  BRAKE CONTROL  


CONSTRUCTION


a.

The brake control system consists of the master cylinder cut solenoid valve, pressure holding solenoid valve, pressure reduction solenoid valve, etc., and controls the brake fluid pressure in each wheel cylinder.

Hydraulic Circuit (Not Operating)
X114908C03
2.583,0.865 2.74,0.865 2.74,0.865 2.927,0.635 true 0.573,1.365 0.5,1.042 0.5,1.042 0.375,1.042 true 3.417,4.115 3.417,3.854 3.417,3.854 3.094,3.667 true 3.719,4.115 3.719,3.854 3.719,3.854 4.073,3.646 true 3.281,6.208 3.281,5.688 true 3.875,6.198 3.875,5.677 true 2.417,0.792 2.729,0.948 0.313,0.156 10 false *1 0.188,0.969 0.5,1.125 0.313,0.156 10 false *2 3.448,1.781 3.76,1.938 0.313,0.156 10 false *3 0.792,2.604 1.104,2.76 0.313,0.156 10 false *4 6.208,2.604 6.521,2.76 0.313,0.156 10 false *5 1.063,3.771 1.375,3.927 0.313,0.156 10 false *6 3.354,4.177 3.667,4.333 0.313,0.156 10 false *7 3.208,6.25 3.521,6.406 0.313,0.156 10 false *9 1.052,6.469 1.521,6.625 0.469,0.156 10 false *a 2.292,6.469 2.76,6.625 0.469,0.156 10 false *b 4.729,6.469 5.198,6.625 0.469,0.156 10 false *c 5.938,6.458 6.406,6.615 0.469,0.156 10 false *d 2.26,3.781 2.573,3.938 0.313,0.156 10 false *6 4.74,3.771 5.052,3.927 0.313,0.156 10 false *6 5.927,3.771 6.24,3.927 0.313,0.156 10 false *6 1.073,4.958 1.385,5.115 0.313,0.156 10 false *8 2.25,4.958 2.563,5.115 0.313,0.156 10 false *8 4.729,4.948 5.042,5.104 0.313,0.156 10 false *8 5.927,4.958 6.24,5.115 0.313,0.156 10 false *8 3.646,4.177 3.958,4.333 0.313,0.156 10 false *7 3.792,6.25 4.104,6.406 0.313,0.156 10 false *9
*1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
*3 Master Cylinder Pressure Sensor *4 No. 1 Master Cylinder Cut Solenoid Valve
*5 No. 2 Master Cylinder Cut Solenoid Valve *6 Pressure Holding Solenoid Valve
*7 Pump *8 Pressure Reduction Solenoid Valve
*9 Reservoir - -
*a Front Brake Caliper RH *b Rear Brake Caliper LH
*c Rear Brake Caliper RH *d Front Brake Caliper LH



b.

Pressure Holding Solenoid Valve and Pressure Reduction Solenoid Valve

·

The skid control ECU increases, holds or decreases the brake fluid pressure of each wheel cylinder by individually turning its pressure holding solenoid valve and pressure reduction solenoid valve on or off.



c.

Master Cylinder Cut Solenoid Valve

·

A linear solenoid valve is used for the master cylinder cut solenoid valve, minimizing fluctuations in the brake fluid pressure during control.

·

The master cylinder cut solenoid valve is turned on or off to control the brake fluid pressure from the pump to the wheel cylinder.

X113254C01
0.292,0.208 2.5,3.594 2.208,3.385 2.792,0.208 6.906,3.594 4.115,3.385 3.667,0.458 4,0.708 0.333,0.25 5.844,0.479 6.177,0.729 0.333,0.25 0.656,0.615 0.969,0.771 0.313,0.156 10 false *1 1.99,1.573 2.302,1.729 0.313,0.156 10 false *2 0.604,2.094 0.917,2.25 0.313,0.156 10 false *3 1.385,2.708 1.698,2.865 0.313,0.156 10 false *4 6.042,3.365 6.354,3.521 0.313,0.156 10 false *5 0.344,0.271 0.656,0.427 0.313,0.156 10 false *a 2.854,0.271 3.167,0.427 0.313,0.156 10 false *b 3.75,0.521 4.063,0.677 0.313,0.156 10 false *c 5.938,0.542 6.25,0.698 0.313,0.156 10 false *d 4.49,1.573 4.802,1.729 0.313,0.156 10 false *2 6.625,1.583 6.938,1.74 0.313,0.156 10 false *2 3.885,2.688 4.198,2.844 0.313,0.156 10 false *4 6.042,2.698 6.354,2.854 0.313,0.156 10 false *4 1.375,3.375 1.688,3.531 0.313,0.156 10 false *5 3.885,3.365 4.198,3.521 0.313,0.156 10 false *5 3.156,0.615 3.469,0.771 0.313,0.156 10 false *1 5.302,0.615 5.615,0.771 0.313,0.156 10 false *1
*1 Master Cylinder *2 Pump
*3 Master Cylinder Cut Solenoid Valve *4 Pressure Holding Solenoid Valve
*5 Brake Caliper - -
*a Not Operating *b Operating
*c Required Brake Fluid Pressure: Low *d Required Brake Fluid Pressure: High




d.

Maser Cylinder Pressure Sensor

·

The master cylinder pressure sensor is built into the brake actuator assembly and detects and outputs the brake fluid pressure from the master cylinder to the skid control ECU.




OPERATION


a.

ABS and EBD

i.

The ABS and EBD systems control the pump, pressure holding solenoid valve and pressure reduction solenoid valve to control the brake fluid pressure of each wheel cylinder.

X112181C01
0.677,0.135 2.531,3.719 1.854,3.583 2.698,0.125 4.552,3.708 1.854,3.583 4.76,0.115 6.615,3.698 1.854,3.583 1.219,1.833 1.313,1.833 1.313,1.833 1.51,1.313 true 1.177,3.313 1.281,3.313 1.281,3.313 1.51,2.771 true 0.74,0.146 1.021,0.323 0.281,0.177 10 false *a 2.771,0.156 3.156,0.333 0.385,0.177 10 false *b 4.823,0.135 5.125,0.333 0.302,0.198 10 false *c 0.938,0.802 1.302,0.99 0.365,0.188 10 false *1 2.979,0.792 3.292,0.979 0.313,0.188 10 false *1 5,0.802 5.333,1.031 0.333,0.229 10 false *1 0.958,2.292 1.375,2.51 0.417,0.219 10 false *2 2.948,2.313 3.271,2.552 0.323,0.24 10 false *2 4.979,2.302 5.365,2.531 0.385,0.229 10 false *2 2.115,3.49 2.448,3.646 0.333,0.156 10 false *e 1.042,1.76 1.333,1.927 0.292,0.167 10 false *g 1.01,3.25 1.375,3.438 0.365,0.188 10 false *f 4.979,1.875 5.375,2.073 0.396,0.198 10 false *d
*1 Pressure Holding Solenoid Valve *2 Pressure Reduction Solenoid Valve
*a Pressure Increase Mode *b Pressure Holding Mode
*c Pressure Reduction Mode *d To Reservoir
*e To Brake Caliper *f Port 2
*g Port 1 - -


ABS and EBD Operation
Pressure Mode Increase Mode Holding Mode Reduction Mode
Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) ON (Open)
Port 1 Open Closed Closed
Port 2 Closed Closed Open
Wheel Cylinder Pressure Increases Holds Reduces



b.

Brake Assist

i.

Brake assist controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply brake fluid pressure higher than that of the master cylinder from the pump of the brake actuator assembly to each wheel cylinder.

Brake Assist Control Operation
X114909C05
0.813,1.635 1.125,1.792 0.313,0.156 10 false *1 6.167,1.635 6.479,1.792 0.313,0.156 10 false *2 1.479,2.021 1.792,2.177 0.313,0.156 10 false *3 1.479,2.958 1.792,3.115 0.313,0.156 10 false *4 0.708,0.042 1.021,0.198 0.313,0.156 10 false *a 0.75,4.448 1.063,4.604 0.313,0.156 10 false *b 2.969,4.469 3.281,4.625 0.313,0.156 10 false *c 4.344,4.479 4.656,4.635 0.313,0.156 10 false *d 6.552,4.448 6.865,4.604 0.313,0.156 10 false *e 2.646,2.021 2.958,2.177 0.313,0.156 10 false *3 4.417,2.021 4.729,2.177 0.313,0.156 10 false *3 5.573,2.021 5.885,2.177 0.313,0.156 10 false *3 2.656,2.958 2.969,3.115 0.313,0.156 10 false *4 4.417,2.958 4.729,3.115 0.313,0.156 10 false *4 5.594,2.958 5.906,3.115 0.313,0.156 10 false *4 6.344,0.042 6.656,0.198 0.313,0.156 10 false *a
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


Brake Assist Control Operation
Brake Assist Not Activated Activated

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.

No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON*
Pressure Holding Solenoid Valve OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure Equivalent to Master Cylinder Brake Fluid Pressure Higher Pressure Required than Master Cylinder Brake Fluid Pressure



c.

TRC

i.

TRC limits the drive force from the engine and controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply more brake fluid pressure from the pump of the brake actuator assembly to the wheel cylinder of each drive wheel to reduce slippage.

TRC Control Operation
X114909C03
0.813,1.635 1.125,1.792 0.313,0.156 10 false *1 6.167,1.635 6.479,1.792 0.313,0.156 10 false *2 1.479,2.021 1.792,2.177 0.313,0.156 10 false *3 1.479,2.958 1.792,3.115 0.313,0.156 10 false *4 0.688,0.031 1,0.188 0.313,0.156 10 false *a 0.75,4.448 1.063,4.604 0.313,0.156 10 false *b 2.969,4.469 3.281,4.625 0.313,0.156 10 false *c 4.344,4.479 4.656,4.635 0.313,0.156 10 false *d 6.552,4.448 6.865,4.604 0.313,0.156 10 false *e 2.646,2.021 2.958,2.177 0.313,0.156 10 false *3 4.417,2.021 4.729,2.177 0.313,0.156 10 false *3 5.573,2.021 5.885,2.177 0.313,0.156 10 false *3 2.656,2.958 2.969,3.115 0.313,0.156 10 false *4 4.417,2.958 4.729,3.115 0.313,0.156 10 false *4 5.594,2.958 5.906,3.115 0.313,0.156 10 false *4 6.344,0.031 6.656,0.188 0.313,0.156 10 false *a
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


TRC Control Operation
TRC Not Activated Activated
Increase Mode Holding Mode Reduction Mode

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.

No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces



d.

VSC (for Oversteer)

i.

The VSC system controls the brake fluid pressure of each wheel cylinder in order to control rear wheel skidding.


ii.

When the vehicle is oversteering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction solenoid valve as shown in the illustration, in order to control rear wheel skidding.

VSC Control Operation (Oversteer Restraining Control)
X114911C02
0.823,1.625 1.135,1.781 0.313,0.156 10 false *1 6.188,1.635 6.5,1.792 0.313,0.156 10 false *2 1.479,2.021 1.792,2.177 0.313,0.156 10 false *3 1.479,2.938 1.792,3.094 0.313,0.156 10 false *4 0.698,0.021 1.01,0.177 0.313,0.156 10 false *a 0.771,4.448 1.083,4.604 0.313,0.156 10 false *b 2.979,4.438 3.292,4.594 0.313,0.156 10 false *c 4.354,4.448 4.667,4.604 0.313,0.156 10 false *d 6.563,4.427 6.875,4.583 0.313,0.156 10 false *e 2.635,2.021 2.948,2.177 0.313,0.156 10 false *3 4.417,2.021 4.729,2.177 0.313,0.156 10 false *3 5.563,2.021 5.875,2.177 0.313,0.156 10 false *3 2.625,2.938 2.938,3.094 0.313,0.156 10 false *4 4.427,2.938 4.74,3.094 0.313,0.156 10 false *4 5.573,2.938 5.885,3.094 0.313,0.156 10 false *4 6.354,0.01 6.667,0.167 0.313,0.156 10 false *a
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


VSC Control Operation (During Oversteer)
VSC Not Activated Activated
Increase Mode Holding Mode Reduction Mode

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.

No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel RH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -
Front Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel RH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -
Rear Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces



e.

VSC (for Understeer)

i.

The VSC system controls the brake fluid pressure of each wheel cylinder in order to control rear wheel skidding.


ii.

When the vehicle is oversteering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction solenoid valve as shown in the illustration, in order to control rear wheel skidding.

VSC Control Operation (Understeer Restraining Control)
X114912C02
0.833,1.615 1.146,1.771 0.313,0.156 10 false *1 6.188,1.615 6.5,1.771 0.313,0.156 10 false *2 1.479,2 1.792,2.156 0.313,0.156 10 false *3 1.479,2.917 1.792,3.073 0.313,0.156 10 false *4 0.688,0.042 1,0.198 0.313,0.156 10 false *a 0.76,4.479 1.073,4.635 0.313,0.156 10 false *b 2.99,4.458 3.302,4.615 0.313,0.156 10 false *c 4.375,4.469 4.688,4.625 0.313,0.156 10 false *d 6.573,4.438 6.885,4.594 0.313,0.156 10 false *e 6.333,0.01 6.646,0.167 0.313,0.156 10 false *a 2.635,2 2.948,2.156 0.313,0.156 10 false *3 4.417,2 4.729,2.156 0.313,0.156 10 false *3 5.573,2 5.885,2.156 0.313,0.156 10 false *3 2.646,2.917 2.958,3.073 0.313,0.156 10 false *4 4.427,2.917 4.74,3.073 0.313,0.156 10 false *4 5.573,2.917 5.885,3.073 0.313,0.156 10 false *4
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


VSC Control Operation (During Understeer)
VSC Not Activated Activated
Increase Mode Holding Mode Reduction Mode

*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions.

No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON* ON* ON*
Front Wheel RH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Front Wheel LH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel RH Pressure Holding Solenoid Valve OFF (Open) OFF (Open) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
Wheel Cylinder Pressure - Increases Holds Reduces
Rear Wheel LH Pressure Holding Solenoid Valve OFF (Open) ON (Closed) ON (Closed) ON (Closed)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - - - -



f.

Active Cornering Assist (ACA)

i.

Active Cornering Assist (ACA), by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer tendencies are controlled.


ii.

Understeer restraining control is performed by applying the brakes for the wheels on the inner circle of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking.


iii.

The operation of the solenoid valves under the Active Cornering Assist (ACA) is the same as the operation of the VSC understeer restraining control.



g.

Hill-start Assist Control

i.

Hill-start assist control temporarily maintains the brake fluid pressure of all 4 wheels to prevent the vehicle from rolling backward.

Hill-start Assist Control Operation with the Shift Lever in D (Driver Depresses Accelerator to Start Off)
X113265E07
2.073,0.875 2.344,0.417 2.344,0.417 2.573,0.417 true 2.26,2.156 2.521,1.083 2.521,1.083 2.635,1.083 true 1.052,0.448 1.604,0.635 0.552,0.188 10 false Forward 1.146,0.802 2.115,1.01 0.969,0.208 10 false Speed 0.948,1.198 1.667,1.406 0.719,0.208 10 false Backward 2.646,0.354 4.354,0.625 1.708,0.271 10 false Vehicle stopped 5.333,0.958 5.781,1.156 0.448,0.198 10 false Time 5.365,2.688 5.823,2.885 0.458,0.198 10 false Time 2.677,1.01 4.469,1.542 1.792,0.531 10 false Required brake fluid pressure to keep the vehicle stationary 4.917,1.625 6.406,1.813 1.49,0.188 10 false : Brake Pedal Operation 4.927,1.365 6.438,1.625 1.51,0.26 10 false : Brake Fluid Pressure 2.417,3.333 4.552,3.583 2.135,0.25 10 false Hill-start Assist Control Operating 2.76,2.865 4.792,3.188 2.031,0.323 10 false Accelerator pedal depressed 0.281,2.24 1.615,2.469 1.333,0.229 10 false Brake Fluid Pressure

Hill-start Assist Control Operation with the Shift Lever in D (Driver does Nothing)
X113266E01
2.281,2.156 2.417,1.073 2.417,1.073 2.531,1.073 true 2.073,0.875 2.333,0.51 2.333,0.51 2.625,0.51 true 1.042,0.469 1.594,0.677 0.552,0.208 10 false Forward 1.135,0.813 2.073,1.01 0.938,0.198 10 false Speed 0.938,1.146 1.635,1.344 0.698,0.198 10 false Backward 0.24,2.094 1.729,2.302 1.49,0.208 10 false Brake Fluid Pressure 2.667,0.458 3.885,0.729 1.219,0.271 10 false Vehicle stopped 2.583,0.99 4.385,1.542 1.802,0.552 10 false Required brake fluid pressure to keep the vehicle stationary 4.792,1.354 6.365,1.594 1.573,0.24 10 false : Brake Fluid Pressure 4.792,1.625 6.323,1.823 1.531,0.198 10 false : Brake Pedal Operation 5.375,0.938 5.823,1.146 0.448,0.208 10 false Time 5.427,2.667 5.854,2.865 0.427,0.198 10 false Time 3.708,2.75 4.698,2.979 0.99,0.229 10 false Approx. 2 sec. 2.698,3.344 4.854,3.573 2.156,0.229 10 false Hill-start Assist Control Operating

Hill-start Assist Control Operation
X114913C02
0.865,1.625 1.177,1.781 0.313,0.156 10 false *1 6.188,1.625 6.5,1.781 0.313,0.156 10 false *2 1.469,2.031 1.781,2.188 0.313,0.156 10 false *3 1.469,2.938 1.781,3.094 0.313,0.156 10 false *4 0.688,0.042 1,0.198 0.313,0.156 10 false *a 0.75,4.458 1.063,4.615 0.313,0.156 10 false *b 2.99,4.448 3.302,4.604 0.313,0.156 10 false *c 4.365,4.448 4.677,4.604 0.313,0.156 10 false *d 6.563,4.438 6.875,4.594 0.313,0.156 10 false *e 6.354,0.042 6.667,0.198 0.313,0.156 10 false *a 2.615,2.031 2.927,2.188 0.313,0.156 10 false *3 4.438,2.031 4.75,2.188 0.313,0.156 10 false *3 5.573,2.031 5.885,2.188 0.313,0.156 10 false *3 2.625,2.938 2.938,3.094 0.313,0.156 10 false *4 4.448,2.938 4.76,3.094 0.313,0.156 10 false *4 5.594,2.938 5.906,3.094 0.313,0.156 10 false *4
*1 No. 1 Master Cylinder Cut Solenoid Valve *2 No. 2 Master Cylinder Cut Solenoid Valve
*3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
*a From Brake Master Cylinder Sub-assembly *b To Front Brake Caliper RH
*c To Rear Brake Caliper LH *d To Rear Brake Caliper RH
*e To Front Brake Caliper LH - -


Hill-start Assist Control Operation
Hill-start Assist Control Not Activated Activated
Holding Mode Reduction Mode
No. 1 Master Cylinder Cut Solenoid Valve OFF (Open) ON (Closed) OFF (Open)
No. 2 Master Cylinder Cut Solenoid Valve OFF (Open) ON (Closed) OFF (Open)
Front Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - Holds Reduces
Rear Wheel Pressure Holding Solenoid Valve OFF (Open) OFF (Open) OFF (Open)
Pressure Reduction Solenoid Valve OFF (Closed) OFF (Closed) OFF (Closed)
Wheel Cylinder Pressure - Holds Reduces



h.

Brake Hold

i.

The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.



i.

VSC and Cooperative Control with EPS

i.

The operation of the solenoid valves under the VSC and cooperative control with EPS is the same as the TRC or VSC operation.



j.

Trailer Sway Control

i.

The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.



k.

Multi-terrain Select

i.

The operation of the solenoid valves under the multi-terrain select is the same as the TRC operation.