Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
NM37A0E _51 Engine / Hybrid System _086659 2GR-FKS ENGINE CONTROL _0419212 SFI SYSTEM DE DETAILS F

2GR-FKS ENGINE CONTROL  SFI SYSTEM  DETAILS  CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magnetic Resistance Element (MRE) type camshaft position sensors (intake and exhaust) are used. To detect each camshaft position, a timing rotor that is secured to the camshaft is used to generate 3 pulses for every 2 revolutions of the crankshaft. The timing rotor for each camshaft is part of the respective camshaft.

W144725E01
4.083,1.083 4.25,1.083 4.25,1.083 4.5,1.333 true 6.083,1.333 6.083,1.083 6.083,1.083 6.25,1.083 true 1.719,2.906 1.969,2.906 1.969,2.906 2.729,3.375 true 1.667,4.323 2.417,4.323 2.417,4.323 4.063,4.625 true 3.177,3.417 4.5,2.917 4.5,2.917 4.75,2.917 true 4.635,4.865 5.417,4.25 5.417,4.25 5.667,4.25 true 1.396,0.365 2.031,0.583 0.635,0.219 10 false 120° CA 2.625,0.646 3.26,0.865 0.635,0.219 10 false 120° CA 2.583,1.917 3.219,2.135 0.635,0.219 10 false 180° CA 1.104,2.406 1.74,2.625 0.635,0.219 10 false 60° CA 0.479,2.073 1.115,2.292 0.635,0.219 10 false 60° CA 0.156,0.781 0.792,1 0.635,0.219 10 false 180° CA 5.167,0.885 5.802,1.104 0.635,0.219 10 false 720° CA 3.458,0.99 4.031,1.208 0.573,0.219 10 false 120° CA 6.292,0.979 6.927,1.198 0.635,0.219 10 false 60° CA 5.188,1.354 5.823,1.573 0.635,0.219 10 false 180° CA 4.656,1.938 5.292,2.156 0.635,0.219 10 false 120° CA 5.656,1.938 6.292,2.156 0.635,0.219 10 false 60° CA 6.281,1.938 6.917,2.156 0.635,0.219 10 false 180° CA 0.063,2.802 1.677,3.323 1.615,0.521 10 false Camshaft Position Sensor (Bank 1 Exhaust) 0.031,4.208 1.677,4.74 1.646,0.531 10 false Camshaft Position Sensor (Bank 2 Intake) 4.823,2.813 6.469,3.333 1.646,0.521 10 false Camshaft Position Sensor (Bank 1 Intake) 5.74,4.146 6.906,4.917 1.167,0.771 10 false Camshaft Position Sensor (Bank 2 Exhaust)


b.

An MRE type camshaft position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the camshaft position based on this output voltage.


c.

The differences between an MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

·

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the camshaft at an early stage of cranking.

·

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.


MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126804E01
4.292,3.083 4.292,2.667 true 4.656,1.896 4.656,1.031 4.656,1.031 4.823,1.031 true 0.01,1.125 0.938,1.417 0.927,0.292 10 false Engine Speed 3.01,1.104 3.938,1.396 0.927,0.292 10 false Engine Speed 0,2.74 0.927,3.031 0.927,0.292 10 false Sensor Output 3.021,2.438 3.948,2.729 0.927,0.292 10 false Sensor Output 2.104,3.125 2.99,3.354 0.885,0.229 10 false Digital Output 1.542,3.427 2.302,3.646 0.76,0.219 10 false MRE Type 4.76,3.469 5.729,3.688 0.969,0.219 10 false Pick-up Type 3.917,3.135 5.24,3.354 1.323,0.219 10 false Non Detection Area 6.031,2.708 7,2.948 0.969,0.24 10 false Analog Output 4.896,0.948 6.198,1.188 1.302,0.24 10 false Non Detection Area