Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
NM37A0E _59 Vehicle Exterior _086696 WIPER / WASHER _0419450 WIPER AND WASHER SYSTEM CO CONTROL F

WIPER / WASHER  WIPER AND WASHER SYSTEM  CONTROL  WIPER CONTROL  


FUNCTION OF MAIN COMPONENTS


Front Wiper System
Component Function

*1: Models without rain sensing function

*2: Models with rain sensing function

Windshield Wiper Switch Assembly
·

Front Washer Switch

·

Interval Time Adjuster*1

·

Automatic Control Adjuster*2

·

Front Wiper Control Switch


·

Outputs the position signal of the windshield wiper switch assembly to the windshield wiper motor assembly via the main body ECU (multiplex network body ECU).

·

Setting the AUTO switch on will cause the rain sensing function to operate.*2


Rain Sensor*2 Senses rain when the AUTO switch (windshield wiper switch assembly) is on, and sends signals to the windshield wiper relay assembly via the main body ECU (multiplex network body ECU).
Windshield Wiper Motor Assembly Activates the front wipers in accordance with the position signal of the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Washer Motor and Pump Assembly Activates in accordance with the signal from the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Wiper Relay Assembly Receives the operation signal from the main body ECU (multiplex network body ECU), and inputs them into the windshield wiper motor assembly and windshield washer motor and pump assembly.
Combination Meter Assembly Sends the vehicle speed signal to the main body ECU (multiplex network body ECU).
Main Body ECU (Multiplex Network Body ECU) Receives signals from various sensors and ECUs and sends them to the windshield wiper relay assembly.
Steering Sensor Outputs the position signal of the windshield wiper switch assembly to the main body ECU (multiplex network body ECU).
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.

Rear Wiper System
Component Function
Windshield Wiper Switch Assembly
·

Rear Washer Switch

·

Rear Wiper Control Switch


Outputs the position signal of the windshield wiper switch assembly to the rear wiper motor assembly via the main body ECU (multiplex network body ECU).
Rear Wiper Motor Assembly Activates the rear wipers in accordance with the position signal of the windshield wiper switch assembly via the main body ECU (multiplex network body ECU).
Windshield Washer Motor and Pump Assembly Activates in accordance with the signal from the windshield wiper switch assembly via the windshield wiper relay assembly.
Windshield Wiper Relay Assembly Receives the operation signal from the main body ECU (multiplex network body ECU), and inputs them into the windshield washer motor and pump assembly.
Main Body ECU (Multiplex Network Body ECU) Receives signals from various sensors and ECUs and sends them to the windshield wiper relay assembly and rear wiper motor assembly.
Steering Sensor Outputs the position signal of the windshield wiper switch assembly to the main body ECU (multiplex network body ECU).
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.

Washer Fluid Level Warning Function (Models with Washer Fluid Level Warning Function)
Component Function
Combination Meter Assembly Warns the driver through the warning message on the multi-information display when the volume of washer fluid decreases to below a certain level.
Level Warning Switch Assembly Outputs a signal to the combination meter assembly when the volume of washer fluid decreases to below a certain level.


FUNCTION


a.

Rain Sensing Function (Models with Rain Sensing Function)

i.

When the AUTO switch (windshield wiper switch assembly) is on, the rain sensor mounted on the upper area of the windshield detects the amount of rain and the luminance of the surrounding area. When the rain sensor detects rain, it sends an optimal wiper timing signal to the windshield wiper relay assembly in accordance with the vehicle speed, luminance of the surrounding area and the amount of rain detected.


ii.

The windshield wiper relay assembly changes the operation of the windshield wiper motor assembly as shown in the following table, based on wiper operation request signals sent from the rain sensor. If a wiper HI operation request signal is received due to a sudden increase of the amount of rain, such as a splash on the windshield, the wipers are operated continuously on HI.


iii.

The rain sensor detects the luminance of the surrounding area. If the luminance changes such as when the vehicle goes in or out of a tunnel, the rain sensor sends a wiper operation request signal in accordance with the situation, enabling the wipers to operate at a comfortable setting.

Wiper Operation
Amount of Rain While Being Driven While Stopped
Large Continuously (at HI) Continuously (at LO)
↓↑ Continuously (at LO) Continuously (at LO)
↓↑ Intermittently at Approximately 0.6-second Intervals Intermittently at Approximately 0.8-second Intervals
↓↑ Intermittently at Approximately 1.2-second Intervals Intermittently at Approximately 1.6-second Intervals
↓↑ Intermittently at Approximately 2.1-second Intervals Intermittently at Approximately 3.1-second Intervals
↓↑ Intermittently at Approximately 3.5-second Intervals Intermittently at Approximately 5.4-second Intervals
↓↑ Intermittently at Approximately 5.9-second Intervals Intermittently at Approximately 9.7-second Intervals
↓↑ Intermittently at Approximately 10.1-second Intervals Intermittently at Approximately 17.5-second Intervals
Small Intermittently at Approximately 17.9-second Intervals Intermittently at Approximately 32.7-Second Intervals
No detection Not operated Not operated



b.

Rain Sensor Sensitivity Adjustment Function (Models with Rain Sensing Function)

i.

When the wiper control switch (windshield wiper switch assembly) is in AUTO, operating the sensitivity switch adjusts the sensitivity of the rain sensor to adjust the wiper operation timing.

HINT:

When the sensitivity switch is operated to the sensitive side, the wipers operate once regardless of the amount of rain.




c.

Washer-linked Wiper with Drip-prevention Function

i.

When the windshield wiper switch assembly is set to off or AUTO* and the washer switch is turned on more than 0.5 seconds, the wipers start on LO at the same time as the washer fluid is sprayed.

*: Models with rain sensing function


ii.

The wipers operate 3 times on LO after the washer switch is turned off.


iii.

When the washer switch is turned on for approximately 0.5 seconds or more and vehicle speed is approximately 7 km/h (4 mph) or less, as shown in the following diagram, after the end of this operation, the wipers operate once more.

Y137334E01
0.833,0.969 1.75,1.188 0.917,0.219 10 false Wiper Switch 0.833,2 1.844,2.219 1.01,0.219 10 false Washer Motor 0.833,3.198 1.927,3.479 1.094,0.281 10 false Wiper Operation 2.083,0.708 2.396,0.906 0.313,0.198 10 false On 2.083,1.281 2.542,1.479 0.458,0.198 10 false Off 2.76,0.333 4.615,0.667 1.854,0.333 10 false Approximately 0.5 Seconds 2.083,2.302 2.542,2.5 0.458,0.198 10 false Off 2.083,1.76 2.396,1.958 0.313,0.198 10 false On 2.083,3.49 2.542,3.688 0.458,0.198 10 false Off 2.094,2.958 2.406,3.156 0.313,0.198 10 false On 3.365,4 4.281,4.677 0.917,0.677 10 false Washer-linked Operation 4.385,3.833 5.167,4.083 0.781,0.25 10 false 3 Seconds 5.229,4 6.177,4.5 0.948,0.5 10 false Drip-prevention Operation



d.

Vehicle Speed-Sensing, Adjustable Interval Function

i.

When the windshield wiper switch assembly is in the INT position, the interval time of the wiper is controlled in 3 stages in accordance with the automatic control adjuster position*1/interval time adjuster position*2 and the vehicle speed.

*1: Models with rain sensing function

*2: Models without rain sensing function


ii.

The interval time can be controlled steplessly within each range.

Models with Rain Sensing Function
Y210310E04
3.938,3.333 3.938,3.469 3.938,3.469 5.271,3.469 false 3.802,1.677 3.802,1.531 3.802,1.531 5.073,1.531 false 2.573,4.042 3.781,4.375 1.208,0.333 10 false Vehicle Speed 2.031,2.229 4.333,2.625 2.302,0.396 10 false Automatic Control Adjustment Range 0.5,1.802 0.979,2.323 0.479,0.521 10 false Interval Time 5.125,1.448 6.813,2.042 1.688,0.594 10 false Automatic Control Adjuster Position: SLOW 5.365,3.375 7.042,3.979 1.677,0.604 10 false Automatic Control Adjuster Position: FAST 1.115,0.333 1.698,0.615 0.583,0.281 10 false Sec. 1.146,0.615 1.521,0.833 0.375,0.219 10 false 15 1.177,1.594 1.479,1.802 0.302,0.208 10 false 10 1.208,2.552 1.469,2.76 0.26,0.208 10 false 5 1.75,3.635 1.958,3.927 0.208,0.292 10 false 0 4.531,3.677 5.427,3.938 0.896,0.26 10 false km/h (mph) 2.396,3.625 3.135,3.875 0.74,0.25 10 false 20 (12) 3.177,3.646 3.823,3.885 0.646,0.24 10 false 40 (25) 3.958,3.635 4.583,3.938 0.625,0.302 10 false 60 (37)

Models without Rain Sensing Function
Y210310E05
3.938,3.333 3.938,3.469 3.938,3.469 5.271,3.469 false 3.802,1.677 3.802,1.531 3.802,1.531 5.073,1.531 false 2.573,4.042 3.781,4.375 1.208,0.333 10 false Vehicle Speed 2.052,2.26 4.438,2.719 2.385,0.458 10 false Interval Time Adjustment Range 0.5,1.802 1.104,2.448 0.604,0.646 10 false Interval Time 5.125,1.448 6.479,2.052 1.354,0.604 10 false Interval Time Adjuster Position: SLOW 5.365,3.375 6.708,3.979 1.344,0.604 10 false Interval Time Adjuster Position: FAST 1.115,0.333 1.698,0.615 0.583,0.281 10 false Sec. 1.146,0.615 1.521,0.833 0.375,0.219 10 false 15 1.177,1.594 1.479,1.802 0.302,0.208 10 false 10 1.208,2.552 1.469,2.76 0.26,0.208 10 false 5 1.75,3.635 1.958,3.927 0.208,0.292 10 false 0 4.531,3.677 5.427,3.938 0.896,0.26 10 false km/h (mph) 2.396,3.625 3.135,3.875 0.74,0.25 10 false 20 (12) 3.177,3.646 3.823,3.885 0.646,0.24 10 false 40 (25) 3.958,3.635 4.583,3.938 0.625,0.302 10 false 60 (37)



e.

Vehicle Speed Switching Function

i.

When the windshield wiper switch assembly is in the LO position and the vehicle stops moving, wiper operation is automatically switched to intermittent operation.


ii.

When the vehicle stops moving and the windshield wiper switch assembly is in the LO position, the wipers operate twice in LO. It then switches to intermittent operation with an interval time of approximately 2.5 seconds. If the vehicle starts moving during this intermittent wiper operation, the wiper automatically returns to LO operation. In addition, setting the automatic control adjuster*1/interval time adjuster*2 in the FAST position operates the wipers in LO when the vehicle stops moving.

*1: Models with rain sensing function

*2: Models without rain sensing function

Y109525E04
1.885,0.365 2.469,0.719 0.583,0.354 10 false Driving 1.771,0.99 2.427,1.396 0.656,0.406 10 false Stopped 1.75,2.875 2.375,3.229 0.625,0.354 10 false Stopped 1.677,2.24 2.427,2.615 0.75,0.375 10 false Operating 2.844,3.125 3.729,3.448 0.885,0.323 10 false LO Operation 5.906,3.146 6.823,3.479 0.917,0.333 10 false LO Operation 4.667,3.135 5.573,3.438 0.906,0.302 10 false INT Operation 3.708,1.531 4.396,2.25 0.688,0.719 10 false Twice Operation 4.521,1.51 4.802,1.781 0.281,0.271 10 false T1 5.104,1.521 5.385,1.833 0.281,0.313 10 false T1 0.479,0.615 1.604,0.948 1.125,0.333 10 false Vehicle Condition 0.552,2.583 1.625,2.948 1.073,0.365 10 false Wiper Operation 0.115,3.427 2.688,3.75 2.573,0.323 10 false T1: Approximately 2.5 seconds



f.

Door Open Linked Wiper Suspend Function (Models with Rain Sensing Function)

i.

When the front door is opened with the shift position P, the front wipers operating and the wiper control switch (windshield wiper switch assembly) in the AUTO position, operation of the front wipers is stopped in order to prevent water splashing while getting in or out of the vehicle.




FAIL-SAFE


a.

If the rain sensor detects a malfunction of the rain sensor during the operation of the rain sensing function, the following controls will be performed:

·

Continuously performs the same wiper operation performed prior to the occurrence of a malfunction.

·

Switches to intermittent operation if a malfunction of the rain sensor is detected when the ignition switch is turned from off to ON or the windshield wiper switch assembly is in the AUTO position.