OUTLINE
The following brake control functions are provided: Anti-lock Brake System (ABS), Electronic Brake force Distribution (EBD), Brake Assist, Traction Control (TRC), Vehicle Stability Control (VSC), Trailer Sway Control, Active Cornering Assist (ACA), Multi-terrain Select*1, Hill-start Assist Control, Downhill Assist Control*1, Brake Hold, VSC and Cooperative Control with EPS, Emergency Brake Signal and Secondary Collision Brake*2.
*1: 4WD/AWD models
*2: Models with pre-collision system
PRECAUTION
ABS
The ABS system cannot increase the performance limit of the tires. Always drive safely and be aware of the vehicle speed and distance to other vehicles.
Any non-standard components such as non-standard tires that are installed may have a negative effect on the ABS function.
When braking using ABS, the braking distance may be longer than vehicles without ABS in the following conditions:
When driving on a dirt road or a road covered with fresh snow
When using tire chains
When driving over a joint in the road surface
When driving on a rough road such as an unpaved or stone-paved road
Brake Assist
Brake assist cannot increase the performance limit of the fundamental brake system. Always drive safely and be aware of the vehicle speed and distance to other vehicles.
TRC, VSC
The TRC and VSC systems ensure traction and vehicle stability. Do not disable the TRC or VSC functions unless necessary.
The TRC and VSC systems cannot increase the performance limit of the tires. Always drive the vehicle carefully in conditions in which drive wheel traction or vehicle stability may be lost.
Active Cornering Assist (ACA)
Active Cornering Assist (ACA) cannot increase the performance limit or innate maneuverability of the vehicle itself.
Do not overly rely on Active Cornering Assist (ACA). Active Cornering Assist (ACA) may not operate effectively when accelerating down slopes or driving on slippery road surfaces.
When Active Cornering Assist (ACA) frequently operates, Active Cornering Assist (ACA) may temporarily stop operating to ensure proper operation of the brakes, TRC and VSC.
Multi-terrain Select
Multi-terrain select is not intended to expand the limits of the vehicle. Thoroughly check the road conditions and drive with caution.
The recommended mode selected by multi-terrain select is only a recommendation. The recommended mode may not be the most appropriate depending on the road conditions (pitch, slipperiness and undulations). Thoroughly check the road conditions before driving.
Multi-terrain select controls the vehicle so that the drive force can be maximized to improve off-road driveability. Therefore, the fuel economy will not be as efficient as when driving without multi-terrain select.
Only use multi-terrain select during off-road driving, and use normal mode at all other times.
Hill-start Assist Control
Hill-start assist control is not intended to keep the vehicle stationary on a hill for a prolonged period. As hill-start assist control only prevents the vehicle from rolling backwards for 2 seconds after the brake pedal is released, perform start-off within this period.
When hill-start assist control is operating and the ignition switch is turned off, hill-start assist control will be canceled without warning.
Hill-start assist control prevents the vehicle from rolling backwards by controlling the brake force to the 4 wheels. However, the vehicle may not remain stationary when on an extremely steep slope or a low friction surface such as ice.
Downhill Assist Control
Check that the downhill assist control indicator light is illuminated before driving. While downhill assist control is operating, the slip indicator light in the combination meter assembly blinks or the brake lights illuminate.
When downhill assist control consecutively operates, the temperature inside the brake actuator increases and downhill assist control may be temporarily canceled.
At this time, a buzzer in the combination meter assembly sounds and the downhill assist control indicator light blinks to inform the driver that downhill assist control is canceled. When the temperature inside the brake actuator assembly decreases and the downhill assist control indicator light returns to the illuminated condition, control via downhill assist control is possible.
On extremely steep slopes and extremely slippery surfaces such as snow-covered roads, it may not be possible to maintain a set vehicle speed.
Brake Hold
Brake hold is not intended to keep the vehicle parked for a prolonged period, such as the parking brake is designed to do.
When brake hold is operating and the ignition switch is turned off, brake hold will be canceled without warning.
If brake hold does not operate even though the vehicle is stopped, firmly depress the brake pedal. If brake hold still does not operate, check the operating conditions.
It may not be possible for brake hold to keep the vehicle stationary on a steep or slippery road.