CONSTRUCTION
The brake control system consists of the master cylinder cut solenoid valve, pressure holding solenoid valve, pressure reduction solenoid valve, etc., and controls the brake fluid pressure in each wheel cylinder.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | No. 1 Master Cylinder Cut Solenoid Valve |
| *5 | No. 2 Master Cylinder Cut Solenoid Valve | *6 | Pressure Holding Solenoid Valve |
| *7 | Pump | *8 | Pressure Reduction Solenoid Valve |
| *9 | Reservoir | - | - |
| *a | Front Brake Caliper RH | *b | Rear Brake Caliper LH |
| *c | Rear Brake Caliper RH | *d | Front Brake Caliper LH |
Pressure Holding Solenoid Valve and Pressure Reduction Solenoid Valve
The skid control ECU increases, holds or decreases the brake fluid pressure of each wheel cylinder by individually turning its pressure holding solenoid valve and pressure reduction solenoid valve on or off.
Master Cylinder Cut Solenoid Valve
A linear solenoid valve is used for the master cylinder cut solenoid valve, minimizing fluctuations in the brake fluid pressure during control.
The master cylinder cut solenoid valve is turned on or off to control the brake fluid pressure from the pump to the wheel cylinder.
| *1 | Master Cylinder | *2 | Pump |
| *3 | Master Cylinder Cut Solenoid Valve | *4 | Pressure Holding Solenoid Valve |
| *5 | Brake Caliper | - | - |
| *a | Not Operating | *b | Operating |
| *c | Required Brake Fluid Pressure: Low | *d | Required Brake Fluid Pressure: High |
Maser Cylinder Pressure Sensor
The master cylinder pressure sensor is built into the brake actuator assembly and detects and outputs the brake fluid pressure from the master cylinder to the skid control ECU.
OPERATION
ABS and EBD
The ABS and EBD systems control the pump, pressure holding solenoid valve and pressure reduction solenoid valve to control the brake fluid pressure of each wheel cylinder.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *a | Pressure Increase Mode | *b | Pressure Holding Mode |
| *c | Pressure Reduction Mode | *d | To Reservoir |
| *e | To Brake Caliper | *f | Port 2 |
| *g | Port 1 | - | - |
| Pressure Mode | Increase Mode | Holding Mode | Reduction Mode |
|---|---|---|---|
| Pressure Holding Solenoid Valve | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | ON (Open) |
| Port 1 | Open | Closed | Closed |
| Port 2 | Closed | Closed | Open |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
Brake Assist
Brake assist controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply brake fluid pressure higher than that of the master cylinder from the pump of the brake actuator assembly to each wheel cylinder.
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| Brake Assist | Not Activated | Activated |
|---|---|---|
|
*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions. |
||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* |
| Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) |
| Wheel Cylinder Pressure | Equivalent to Master Cylinder Brake Fluid Pressure | Higher Pressure Required than Master Cylinder Brake Fluid Pressure |
TRC
TRC limits the drive force from the engine and controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply more brake fluid pressure from the pump of the brake actuator assembly to the wheel cylinder of each drive wheel to reduce slippage.
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| TRC | Not Activated | Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
|
*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions. |
|||||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| Front Wheel | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Rear Wheel | Pressure Holding Solenoid Valve | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | - | - | - | |
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| TRC | Not Activated | Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
|
*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions. |
|||||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| Front Wheel | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Rear Wheel | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
VSC (for Oversteer)
The VSC system controls the brake fluid pressure of each wheel cylinder in order to control rear wheel skidding.
When the vehicle is oversteering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction solenoid valve as shown in the illustration, in order to control rear wheel skidding.
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| VSC | Not Activated | Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
|
*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions. |
|||||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| Front Wheel RH | Pressure Holding Solenoid Valve | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | - | - | - | |
| Front Wheel LH | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Rear Wheel RH | Pressure Holding Solenoid Valve | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | - | - | - | |
| Rear Wheel LH | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
VSC (for Understeer)
The VSC system controls the brake fluid pressure of each wheel cylinder in order to control rear wheel skidding.
When the vehicle is oversteering while turning to the right, the VSC system controls each pressure holding solenoid valve and pressure reduction solenoid valve as shown in the illustration, in order to control rear wheel skidding.
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| VSC | Not Activated | Activated | |||
|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||
|
*: The solenoid valve controls the brake fluid pressure by continually opening and closing the valve in accordance with the operating conditions. |
|||||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON* | ON* | ON* | |
| Front Wheel RH | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Front Wheel LH | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Rear Wheel RH | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| Wheel Cylinder Pressure | - | Increases | Holds | Reduces | |
| Rear Wheel LH | Pressure Holding Solenoid Valve | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | - | - | - | |
Active Cornering Assist (ACA)
Active Cornering Assist (ACA), by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer tendencies are controlled.
Understeer restraining control is performed by applying the brakes for the wheels on the inner circle of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking.
The operation of the solenoid valves under the Active Cornering Assist (ACA) is the same as the operation of the VSC understeer restraining control.
Hill-start Assist Control
Hill-start assist control temporarily maintains the brake fluid pressure of all 4 wheels to prevent the vehicle from rolling backward.
| *1 | No. 1 Master Cylinder Cut Solenoid Valve | *2 | No. 2 Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | From Brake Master Cylinder Sub-assembly | *b | To Front Brake Caliper RH |
| *c | To Rear Brake Caliper LH | *d | To Rear Brake Caliper RH |
| *e | To Front Brake Caliper LH | - | - |
| Hill-start Assist Control | Not Activated | Activated | ||
|---|---|---|---|---|
| Holding Mode | Reduction Mode | |||
| No. 1 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON (Closed) | OFF (Open) | |
| No. 2 Master Cylinder Cut Solenoid Valve | OFF (Open) | ON (Closed) | OFF (Open) | |
| Front Wheel | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | OFF (Open) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | Holds | Reduces | |
| Rear Wheel | Pressure Holding Solenoid Valve | OFF (Open) | OFF (Open) | OFF (Open) |
| Pressure Reduction Solenoid Valve | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| Wheel Cylinder Pressure | - | Holds | Reduces | |
Brake Hold
The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.
VSC and Cooperative Control with EPS
The operation of the solenoid valves under the VSC and cooperative control with EPS is the same as the TRC or VSC operation.
Trailer Sway Control
The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.
Multi-terrain Select
The operation of the solenoid valves under the multi-terrain select is the same as the TRC operation.