FUNCTION OF MAIN COMPONENTS
The main components of the airbag system have the following functions:
| Component | Function | |
|---|---|---|
|
*1: Models with telematics transceiver *2: HV models *3: Gasoline models *4: Models with airbag cut off switch cylinder *5: Models with pre-collision system *6: Models with rear seat belt pretensioners |
||
| Airbag Sensor Assembly | ·
In the event of a frontal collision, the airbag sensor assembly receives the signal from either of the front airbag sensors or main sensor built into the airbag sensor assembly. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving signals from the safing sensor and at least one of the front airbag sensors and main sensor built into the airbag sensor assembly, the airbag sensor assembly determines whether the driver airbag, front passenger airbag, driver knee airbag and curtain shield airbags should be deployed, and the front seat belt pretensioners and rear seat belt pretensioners*6 should be activated. The airbag sensor assembly also diagnosis system malfunctions. ·
In the event of a side or rear side collision, the airbag sensor assembly receives signals from the side airbag sensor assembly, rear airbag sensor. The airbag sensor assembly receives the side airbag sensor assembly, rear airbag sensor signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving signals from at least one of the side sensors and either of the safing sensors (safing sensor built into the airbag sensor assembly), the airbag sensor assembly determines whether the front seat airbag and curtain shield airbags should be deployed, and the front seat belt pretensioners and rear seat belt pretensioners*6 should be activated. The airbag sensor assembly also diagnosis system malfunctions. ·
Sends the collision detection signal to the ECM through the Controller Area Network (CAN) to operate fuel pump control. ·
Sends the collision detection signal to the main body ECU (multiplex network body ECU) to operate the collision door lock release function. ·
Sends a signal indicating a collision has occurred to the main body ECU (multiplex network body ECU) via CAN communication to illuminate the interior lights. ·
Sends the brake control request signal to the No. 2 skid control ECU*2 or skid control ECU*3 through the Controller Area Network (CAN) to operate the secondary collision brake. ·
Sends the collision detection signal to the telematics transceiver (data communication module) for the emergency call of automatic collision notification service.*1 ·
Sends the collision detection signal to the hybrid vehicle control ECU to shut down the hybrid system power supply.*2 ·
Sends a signal indicating a collision has occurred to the combination meter assembly via CAN communication to flash the hazard lights. ·
Prepares the seat belt pretensioners to operate when the PCS (Pre-Collision System) determines that the possibility of a collision with another vehicle is high. |
|
| Horn Button Assembly | Used as supplements to the seat belts to help reduce impact to the occupants. | |
| Instrument Panel Passenger Airbag without Door Assembly | ||
| Lower No. 1 Instrument Panel Airbag Assembly | ||
| Front Seat Airbag Assembly LH/RH | ||
| Curtain Shield Airbag Assembly LH/RH | ||
| Spiral Cable Sub-assembly | Transmits ignition signals from the airbag sensor assembly to the SRS driver airbag. | |
| Front Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a frontal collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Side Airbag Sensor Assembly LH/RH | Detects deformation of the front doors during a side collision using the pressure sensor and sends signals for the airbag sensor assembly to determine if deployment of SRS components is necessary. | |
| Rear Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a rear side collision, distortion is created in the sensor and is converted into an electrical signal. | |
| Front Seat Outer Belt Assembly LH/RH | Used to help reduce impact to the occupants. | |
| Rear Seat Outer Belt Assembly LH/RH*6 | ||
| Hybrid Vehicle Control ECU*2 | Receives the collision detection signal from the airbag sensor assembly during a collision and shuts down the hybrid system power supply by turning the System Main Relays (SMRs) off, in order to ensure safety. | |
| ECM | Receives the collision detection signal from the airbag sensor assembly and stops to the fuel pump. | |
| Main Body ECU (Multiplex Network Body ECU) | ·
Receives the collision detection signal from the airbag sensor assembly and operates the collision door lock release function. ·
Illuminates the map light assembly after receiving a collision detection signal from the airbag sensor assembly. |
|
| Brake Actuator Assembly*5 | No. 2 Skid Control ECU*2 | Receives the brake control request signal from the airbag sensor assembly, and sends brake control signals to the brake actuator to reduce damage of the secondary collision. |
| Skid Control ECU*3 | ||
| Combination Meter Assembly | SRS Warning Light | Turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system. |
| Multi-information Display | Displays a warning message to inform the driver of a malfunction in the airbag system. | |
| Buzzer | Sounds to warn the driver of a malfunction in the airbag system. | |
| Hazard Lights | Flashes the hazard lights after receiving a collision detection signal from the airbag sensor assembly. | |
| Telltale Light Assembly | AIRBAG OFF Indicator Light*4 | Inform the occupants of the airbag cut off switch cylinder sub-assembly status. |
| AIRBAG ON Indicator Light*4 | ||
| Telematics Transceiver (Data Communication Module)*1 | Receives the collision detection signal from the airbag sensor assembly, and automatically makes the emergency call of automatic collision notification service. | |
| Forward Recognition Camera*5 | Detects vehicles, pedestrians and bicycles in front of the vehicle and sends detection information to the airbag sensor assembly via CAN communication. | |
| Millimeter Wave Radar Sensor Assembly*5 | Radiates millimeter wave radar forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the forward recognition camera. | |
| Airbag Cut Off Switch Cylinder Sub-assembly*4 | Suspends the instrument panel passenger airbag without door assembly and front seat airbag assembly RH operations in the event of a frontal collision. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication. | |
| Yawrate Sensor*2 | Sends yawrate sensor signals to the airbag sensor assembly via CAN communication. | |
SYSTEM CONTROL
Airbag for Frontal Collision
There are 5 airbags which deploy in the event of a frontal collision: the horn button assembly, instrument panel passenger airbag without door assembly, lower No. 1 instrument panel airbag assembly and curtain shield airbag assemblies. These airbags deploy simultaneously. The instrument panel passenger airbag without door assembly. In addition, each front pretensioner contained in a front seat outer belt assembly, and each rear pretensioner contained in a rear seat outer belt assembly* are also activated.
*: Models with rear seat belt pretensioners
The airbag sensor assembly detects the information in the table below from various sources.
| Airbag | Information | Source |
|---|---|---|
| Driver | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag Sensor Assembly |
| Front Passenger | Extent of Impact | ·
Front Airbag Sensor LH or RH ·
Airbag Sensor Assembly |
For a frontal collision, if a front airbag sensor detects an impact, it informs the airbag sensor assembly. The airbag sensor assembly causes the horn button assembly, instrument panel passenger airbag without door assembly, lower No. 1 instrument panel airbag assembly and curtain shield airbag assemblies to deploy. Additionally, the airbag sensor assembly activates the seat belt pretensioners for the driver, front passenger and rear passengers*.
*: Models with rear seat belt pretensioners
Deceleration sensors used for the airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag and pretensioner based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. Frontal collision signals are used to deploy all the airbags except all the side airbags and activate all the pretensioners as indicated in the table below.
Airbag for Side/Rear Side Collision
There are 3 airbags which deploy in the event of a severe side collision: the front seat airbag assembly and curtain shield airbag assemblies. These airbags deploy simultaneously. Additionally, at the same time, the front seat belt pretensioners and rear seat belt pretensioners* are also activated.
*: Models with rear seat belt pretensioners
For a side collision, if the side airbag sensor assembly detect an impact, they inform the airbag sensor assembly, and the airbag sensor assembly causes the front seat airbag assembly and curtain shield airbag assemblies to deploy simultaneously, and activate the front seat belt pretensioners and rear seat belt pretensioners*.
*: Models with rear seat belt pretensioners
The front seat airbag assembly and curtain shield airbag assemblies are deployed and each front pretensioner in a front seat outer belt assembly and each rear pretensioner in a rear seat outer belt assembly* are activated based on signals from the side airbag sensor assembly and airbag sensor assembly.
*: Models with rear seat belt pretensioners
For a rear side collision, if the rear airbag sensor detect an impact, they inform the airbag sensor assembly, and the airbag sensor assembly causes the curtain shield airbag assemblies to deploy simultaneously, and activate the rear seat belt pretensioners*.
*: Models with rear seat belt pretensioners
The curtain shield airbag assemblies are deployed and each rear pretensioner in a rear seat outer belt assembly* are activated based on signals from the rear airbag sensor and airbag sensor assembly.
*: Models with rear seat belt pretensioners
Airbag for Roll Over (Models for Russia)
If the vehicle is tilted and rolls over, the airbag sensor assembly activates the front seat belt pretensioners and deploys the curtain shield airbags based on signals that show the vehicle's roll angle and rotation speed.
If the vehicle rolls over in a side collision, the airbag sensor assembly causes the front seat airbag assembly and curtain shield airbag assemblies to deploy and activates the pretensioners based on signals from the side airbag sensor assembly and rear airbag sensor.
Primary Check Illumination Control
After the ignition switch is turned to ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If a malfunction is detected during the primary check, the SRS warning light will remain on even after 6 seconds have elapsed.
After the ignition switch is turned to ON, the airbag sensor assembly operates the AIRBAG ON/OFF indicator lights as shown below to check for an open in the indicator light circuits.
FAIL-SAFE
If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly illuminates the SRS warning light, displays the warning message on the multi-information display and sounds the buzzer to alert the driver of the malfunction.
DIAGNOSIS
If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly stores the malfunction data in memory as Diagnostic Trouble Codes (DTCs).
The airbag sensor assembly outputs malfunction data and 5-digit Diagnostic Trouble Codes (DTCs) to the GTS.
The 5-digit DTCs can be read by connecting the GTS to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag sensor assembly will turn on the SRS warning light. However, unlike an ordinary malfunction, a DTC will not be stored. The SRS warning light cannot be manually turned off. It is necessary to replace the airbag sensor assembly with a new one.