Home › Engine / Hybrid System › 2GR-FKS (IDLING STOP CONTROL) › STOP AND START › from 2020.11
NM37A0E _51 Engine / Hybrid System _096486 2GR-FKS IDLING STOP CONTROL _0453093 STOP AND START DE DETAILS F

2GR-FKS IDLING STOP CONTROL  STOP AND START  DETAILS  COMBINATION METER  


OPERATION


a.

The combination meter assembly receives the idling on/off signals from the engine stop and start ECU.


b.

By changing the display mode of the multi-information display by operating the multi-information switch on the steering pad switch assembly, the amount of time idling stop was performed since the ignition switch was turned to ON to when the ignition switch was turned off or the amount of time idling stop was performed since the reset switch was last pressed can be displayed.


c.

The system operation status or warning information is indicated to the driver through the following means:

·

Illuminating or flashing the stop and start indicator light and stop and start cancel indicator light on the multi-information display in the combination meter assembly.

·

Sounding a buzzer.

·

Displaying other information on the multi-information display.


Models with 4.2 Inch Multi-information Display
W144809C01
1.76,0.313 2.01,0.313 2.01,0.313 2.76,0.896 true 2.917,1.01 3.417,0.344 3.417,0.344 3.75,0.344 true 3.583,2.333 3.583,1.667 true 1.563,0.188 1.75,0.385 0.188,0.198 10 false *a 3.781,0.24 3.969,0.438 0.188,0.198 10 false *b 3.51,2.354 3.698,2.552 0.188,0.198 10 false *c
*a Stop and Start Indicator Light *b Stop and Start Cancel Indicator Light
*c Multi-information Display - -


Models with 7 Inch Multi-information Display
W144810C01
3.583,2.5 3.583,2 true 3.188,0.521 3.385,0.729 0.198,0.208 10 false *a 3.802,0.542 4,0.74 0.198,0.198 10 false *b 3.521,2.531 3.719,2.719 0.198,0.188 10 false *c
*a Stop and Start Indicator Light *b Stop and Start Cancel Indicator Light
*c Multi-information Display - -


Stop and Start Indicator Light Operation
Item Condition Stop and Start Indicator Light Buzzer
System Operating (Engine is stopped) The vehicle is operating normally. Illuminates Does not sound
The driver's door is opened with the shift lever in D. Blinks Sounds

Stop and Start Cancel Indicator Light Operation
Condition Stop and Start Cancel Indicator Light

*: The blinking interval is 0.5 seconds.

The vehicle is stopped and system operation conditions are met. OFF
When the stop and start system cancel switch (ecorun cancel switch assembly) is ON. Illuminates
When any Diagnostic Trouble Code (DTCs) are detected. Blinks*
When the number of times the starter assembly has been operated exceeds the threshold.


d.

Multi-information Display Operation

i.

An indicator and/or messages are displayed on the multi-information display to indicate condition of the stop and start system when certain vehicle conditions are met.

Stop and Start System Condition Multi-information Display Message*1 Vehicle Condition
When the engine cannot be stopped by the stop and start system
V115706

*2
"Press Brake More to Activate" The brake pedal is not depressed enough.
"Non-Dedicated Battery" A non-specified battery for the stop and start system may have been installed.
"Battery Charging"
·

The battery charge amount may be low.

·

A refresh charge may be occurring.


"Stop & Start Unavailable" The engine may have been started with the hood opened.
"In Preparation"
·

The brake booster load decreased.

·

The vehicle is operated at a high elevation.


"For Climate Control"
·

The air conditioning system is being used when the ambient temperature is high or low.

·

Windshield defogger is pressed.


When the engine automatically restarts while stopped by the stop and start system
V115706

*2
"In Preparation" The brake pedal is strongly depressed further or pumped.
"For Climate Control"
·

The air conditioning system is turned on or the air conditioning is being used.

·

Windshield defogger is turned on.


"Battery Charging" The battery charge amount may be low.
The system may be malfunctioning - "Stop & Start System Malfunction. Visit Your Dealer" -

HINT:

*1: Message are listed in the order of priority.

*2: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.