Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2020.11
NM37A0E _59 Vehicle Exterior _086696 WIPER / WASHER _0419450 WIPER AND WASHER SYSTEM GE GENERAL F

WIPER / WASHER  WIPER AND WASHER SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Front Wiper System

i.

The windshield wiper motor assembly and wiper link assembly are mounted in a modular frame, reducing wiper operation sound and reducing variations in the wiping range.


ii.

Diffuser type washer nozzle sub-assemblies are provided under the engine hood to ensure a good appearance.


iii.

A graphite coating is applied to the surface of the wiper rubber, reducing inversion noise and wiper flutter while the wipers are operating.


iv.

A rain sensing function is provided on some models for the front wiper system. This function controls the wiping timing in accordance with the amount of rain detected when the front wiper switch is in the AUTO position.


v.

The front wiper system has the following functions:

Function

*: Models with rain sensing function

Mist function
Front wiper intermittent interval adjustment function
Washer-linked wiper with drip-prevention function
Vehicle speed-sensing, adjustable interval function
Vehicle speed switching function
Door open linked wiper suspend function*
Wiper system with rain sensing function*
Rain sensor sensitivity adjustment function*



b.

Rear Wiper System

i.

The rear wiper system has a washer-linked wiper function and intermittent interval function.


ii.

By using a resin rear wiper arm, a unified rear wiper blade look has been achieved.



c.

Washer Fluid Level Warning Function (Models with Washer Fluid Level Warning Function)

i.

A warning message display function, which shows a warning message on the combination meter assembly when the washer fluid is low, is provided on some models.



d.

Headlight Cleaner System (Models with Headlight Cleaner System)

i.

A headlight cleaner system is provided on some models.


ii.

A headlight cleaner system is used to allow optimal lighting effectiveness to be maintained.



e.

Camera Cleaner System

i.

A camera cleaner system is used.


ii.

The camera cleaner system uses a nozzle installed on top of the inner mirror camera assembly* and rear television camera assembly to spray washer fluid onto the surface of the camera lens, cleaning off foreign matter that is attached to it (such as water, mud, snow and snow-melting agents) and improving the visibility of the camera image.

*: Models with digital rear-view mirror system




PRECAUTION


a.

Camera Cleaner System

i.

Knowledge

1.

If there is a sufficient amount of washer fluid but it does not spray out, check the nozzle for blockages.

2.

The camera cleaner system cleans off foreign matter that is attached to the surface of the camera lens. Therefore, it cannot clean off ice, snow, or other foreign matter that is displayed in the camera image if the foreign matter is attached to surfaces near the camera.

3.

Do not subject the camera to sudden temperature changes such as by pouring hot water into the camera under cold weather.

4.

The washer tank is shared with the windshield washer, so if the camera cleaner system is frequently used, the washer fluid will need to be replaced more often.



ii.

Cautions

1.

Inner Mirror Camera Assembly (Models with Digital Rear-view Mirror System)

(a)

During camera cleaner system operation, the sprayed washer fluid may make it difficult to see the camera image. Drive carefully while confirming the safety of your surroundings.

(b)

If washer fluid remains on the surface of the camera lens after the camera cleaner system operates, the image may become difficult to see at night depending on the headlight height and angle of vehicles to the rear.


2.

Rear Television Camera Assembly

(a)

During camera cleaner system operation, the sprayed washer fluid may make it difficult to see the camera image. Directly check the surrounding conditions in order to ensure safe driving.

(b)

If washer fluid remains on the surface of the camera lens after the camera cleaner system operates, the image may become difficult to see at night depending on the headlight height and angle of vehicles to the rear.

(c)

Do not apply excessive force to the nozzle or subject it to a strong impact. If excessive force is applied to the nozzle or it is subjected to a strong impact, it may become misaligned.




iii.

Handling Guide

1.

Depending on the type of foreign matter attached to the surface of the camera lens, the camera cleaner system may not completely clean the camera lens. If this occurs, wash the camera lens with a large amount of water and wipe the lens with a wet soft cloth.



iv.

Notice

1.

If washer fluid does not spray out, do not continue to operate the rear washer switch. Doing so may damage the pump.

2.

In order to prevent the washer fluid from freezing, use a washer fluid that is appropriate for the outside air temperature.

3.

Do not allow water to directly contact the nozzle when washing the vehicle with a high pressure washer. The camera may stop operating normally if subject to impact from high pressure water. Also, water may enter the nozzle injection opening and freeze, causing the washer fluid to not spray properly.