OUTLINE
The automatic air conditioning system uses left and right independent temperature control and neural network control to enhance comfort.
An inside-and-outside dual air layer type air conditioning unit is used.
S-FLOW control is used to concentrate the air outlets on the driver seat or front seats when the S-FLOW switch is turned on. (Models with S-FLOW Switch)
HFO-1234yf refrigerant is used.
SPECIFICATION
Front Air Conditioning System (HV Models)
| Component | Specifications | |
|---|---|---|
|
*1: Models for Near and Middle East *2: Models for Europe and Australia |
||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 263.9 mm x 120 mm x 27 mm
(10.4 in. x 4.72 in. x 1.06 in.) |
|
| Fin Pitch | 1.8 mm (0.07 in.) | |
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite Brushless |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | Upper side: 122 mm x 55 mm (4.80 in. x 2.17 in.)
Lower side: 125 mm x 38 mm (4.92 in. x 1.50 in.) |
|
| Cooler Condenser Assembly | Type | Multi-Flow IV (MF-IV) Sub-cool |
| Size (W x H x L) | 706 mm x 344.6 mm x 22 mm
(27.8 in. x 13.6 in. x 0.866 in.) |
|
| Fin Pitch | 2.7 mm (0.106 in.) | |
| Compressor Assembly | Type | ESB34C*1
ESB27C*2 |
| Refrigerant | Type | HFO-1234yf |
| No. 1 Cooler Evaporator Sub-assembly | Type | Beneficial Refrigerant Stream (BRS)*1
Ejector Cycle System (ECS)*2 |
| Size (W x H x L) | 279.7 mm x 231 mm x 38 mm
(11.0 in. x 9.09 in. x 1.50 in.) |
|
| Fin Pitch | 3 mm (0.118 in.) | |
Front Air Conditioning System (Gasoline Models)
| Component | Specifications | |
|---|---|---|
|
*1: Models for Australia *2: Models for Russia |
||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 263.9 mm x 120 mm x 27 mm
(10.4 in. x 4.72 in. x 1.06 in.) |
|
| Fin Pitch | 1.8 mm (0.0709 in.) | |
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite Brushless |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | Upper side: 122 mm x 55 mm (4.80 in. x 2.17 in.)
Lower side: 125 mm x 38 mm (4.92 in. x 1.50 in.) |
|
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC) |
| Size (W x H x L) | 700 mm x 529.8 mm x 11.5 mm
(27.6 in. x 20.9 in. x 0.453 in.) |
|
| Fin Pitch | 2.5 mm (0.098 in.) | |
| Cooler Compressor Assembly | Type | 7SAS17C |
| Refrigerant | Type | HFO-1234yf |
| No. 1 Cooler Evaporator Sub-assembly | Type | Cold Storage (CS)*1
Beneficial Refrigerant Stream (BRS)*2 |
| Size (W x H x L) | 279.7 mm x 231 mm x 38 mm
(11.0 in. x 9.09 in. x 1.50 in.) |
|
| Fin Pitch | 3 mm (0.118 in.) | |
Rear Air Conditioning System
| Component | Specifications | |
|---|---|---|
| Rear Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 191.1 mm x 130 mm x 21 mm
(7.5 in. x 5.12 in. x 0.83 in.) |
|
| Fin Pitch | 1.8 mm (0.07 in.) | |
| Rear Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | 140 mm x 58.4 mm (5.51 in. x 2.30 in.) | |
| Rear Cooler Evaporator Sub-assembly | Type | Revolutionary Super-slim (RS) |
| Size (W x H x L) | 145.7 mm x 255 mm x 50 mm
(5.7 in. x 10.04 in. x 1.97 in.) |
|
| Fin Pitch | 3.4 mm (0.134 in.) | |
MAIN FEATURES
The air conditioning system has the following features:
|
*1: HV models *2: Gasoline models *3: HV models for Near and Middle East *4: Gasoline models for Russia *5: HV models for Europe and Australia *6: Gasoline models for Australia |
|
| High Performance | ·
Neural network control is used so passengers can finely control the air conditioning for maximum comfort. ·
A high efficiency type clean air filter, which has a pollen removal effect, is used. ·
The rear outlets are installed on the roof headlining assembly and front deck side trim cover RH to ensure comfortable cooling performance for the rear passengers. ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control. ·
Using the following features of the compressor (continuously variable capacity compressor), high cooling performance and a quiet cabin have been achieved:*2 -
Oil Separator -
Variable Suction Side Throttle -
Solenoid Valve with Built-in Crank Chamber to Suction Passage (CS) Valve |
| Lightweight | ·
An air conditioning harness assembly with a built-in communication/driver IC is used in a lightweight wire harness design to allow a reduced number of wires. ·
The use of this type of connector means that pulse pattern type servo motors can be used. |
| Compact | A blower motor with a built-in blower motor controller is used to achieve a compact construction. |
| Others | The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
·
Semi-center Location Air Conditioning Unit ·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly ·
Multi-Flow IV (MF-IV) Sub-cool Condenser*1 ·
Global Inner-fin Condenser (GIC) Sub-cool Condenser*2 ·
Beneficial Refrigerant Stream (BRS) Evaporator*3, *4 ·
Ejector Cycle System (ECS) Evaporator*5 ·
Cold Storage (CS) Evaporator*6 |
PRECAUTION
Precaution for Refrigerant HFO-1234yf (R1234yf)
Compatibility
The parts used in the refrigerant cycle, the compressor oil, etc. of the HFO-1234yf (R1234yf) system are not compatible with the conventional HFC-134a (R134a) system.
Always use HFO-1234yf (R1234yf) as the refrigerant.
Do not charge the system with refrigerant near open flames, as HFO-1234yf (R1234yf) is combustible.
When charging the system with refrigerant, make sure the area is well ventilated (especially be careful in areas where the gas can easily accumulate such as under lifts and in garage pits, as the gas is heavier than air).
Follow any local regulations regarding combustible gases.
Be sure to use a refrigerant recovery unit that is compatible with HFO-1234yf (R1234yf) systems.
The shape of the service port for refrigerant charging has an exclusive design conforming to international standards for HFO-1234yf (R1234yf) to prevent improper refrigerant charging.
Compressor Oil (Gasoline Models)
Always use ND-OIL 12 as the compressor oil.
When parts of the air conditioning system are removed, quickly block off any areas that are exposed to the outside air with plugs, vinyl tape, etc., as the oil used for HFO-1234yf (R1234yf) systems absorbs moisture easily.
Do not allow the compressor oil to spray, as the oil used for HFO-1234yf (R1234yf) systems has harmful effects on acrylic resins.
Compressor Oil (HV Models)
Always use ND-OIL 11 as the compressor oil.
When parts of the air conditioning system are removed, quickly block off any areas that are exposed to the outside air with plugs, vinyl tape, etc., as the oil used for HFO-1234yf (R1234yf) systems absorbs moisture easily.
Do not allow the compressor oil to spray, as the oil used for HFO-1234yf (R1234yf) systems has harmful effects on acrylic resins.