FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*: Models with hands free power back door function |
||
| Power Back Door ECU (Multiplex Network Door ECU) | ·
Controls the power back door system in accordance with the signals received from the switches, sensors and ECUs. ·
Receives the signals from the Hall IC to detect the back door position and the opening and closing speed of the back door. ·
Informs the user by sounding the buzzer and flashing the hazard warning light when each operation switch is pressed. |
|
| Power Back Door Unit Assembly Set | Back Door Drive Motor | Opens and closes the back door when actuated by the power back door ECU (multiplex network door ECU). |
| Hall IC | Detects the operation conditions of the back door and outputs a pulse signal to the power back door ECU (multiplex network door ECU). | |
| Back Door Lock with Courtesy light Switch Assembly | Back Door Closer Motor | Latches and unlatches the back door when actuated by the power back door ECU (multiplex network door ECU). |
| Latch Switch | Detects if the back door is ajar. | |
| Position Switch | Detects the initial (neutral) position of the driven gear of the back door lock motor. This switch turns on when the driven gear is in the neutral position and turns off when the driven gear is in any position other than neutral. | |
| Back Door Courtesy Switch | Detects whether the back door is open or closed. This switch turns on when the back door is open or ajar and turns off when the back door is closed. | |
| No. 1 Power Back Door Control Switch | The power back door closes when the No. 1 power back door control switch (on the back door jamb) is turned on. | |
| Back Door Opener Switch Assembly | ·
The back door opens when the back door opener switch assembly on the outside of the vehicle is turned on. ·
Outputs signals to the certification ECU (smart key ECU assembly). |
|
| Power Back Door Control Switch | ·
The back door opens and closes when the power back door control switch is turned on. ·
Outputs signals to the power back door ECU (multiplex network door ECU). |
|
| Touch Sensor (Power Back Door Sensor Assembly) | Detects if an object is jammed in the back door during the closing operation of the back door. | |
| Power Back Door Warning Buzzer | When the power back door system starts to operate, the power back door warning buzzer sound to inform the user that the system is operating. | |
| Combination Meter Assembly | ·
Receives a signal to blink the hazard warning light. ·
Outputs a customization signal to the main body ECU (multiplex network body ECU). |
|
| Electrical Key and Tire Pressure Warning ECU and Receiver | Receives the power back door button signal and transmits it to the certification ECU (smart key ECU assembly). | |
| Main Body ECU (Multiplex Network Body ECU) | Sends a back door lock/unlock control signal, vehicle speed signal and shift position P signal to the power back door ECU via the Controller Area Network (CAN). | |
| Electrical Key Transmitter Sub-assembly
·
Power Back Door Button |
Sends the power back door button signal to the electrical key and tire pressure warning ECU and receiver. | |
| Kick Door Control Sensor* | Detects kick operations and outputs signals to the power back door ECU (multiplex network door ECU). | |
SYSTEM CONTROL
The power back door opener function operates when all of the following conditions are met:
The power back door system is on.
The back door is unlocked.
The vehicle speed is approximately 3 km/h (2 mph) or less (only when the ignition switch is ON).
The brake pedal is depressed, the shift position is in P or the parking brake is on (only when the ignition switch is ON).
The power back door closer function operates when all of the following conditions are met:
The power back door system is on.
The vehicle speed is approximately 3 km/h (2 mph) or less (only when the ignition switch is ON).
The brake pedal is depressed, the shift position is in P or the parking brake is on (only when the ignition switch is ON).
Opener Function 1
When the power back door control switch or the power back door button of the electrical key transmitter sub-assembly is operated, the opener function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | After the power back door control switch or the power back door button of the electrical key transmitter sub-assembly is pressed for approximately 0.8 seconds, the power back door buzzer sounds for 0.8 seconds and the hazard warning light blinks twice*. |
| 2 | The back door lock with courtesy light switch assembly (back door closer motor) releases the latch. |
| 3 | The back door courtesy switch is turned on and the motor in the power back door unit assembly set starts to operate. |
| 4 | The back door closer motor is returned to the initial position and the latch switch is turned on. |
| 5 | After the power back door ECU detects a back door stop position pulse, the motor in the power back door unit assembly set is stopped. |
Opener Function 2
When the back door opener switch assembly is operated, the opener function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | After the back door opener switch assembly is pressed, the power back door buzzer sounds for 0.8 seconds and the hazard warning light blinks twice*. |
| 2 | The back door lock with courtesy light switch assembly (back door closer motor) releases the latch. |
| 3 | The back door courtesy switch is turned on and the motor in the power back door unit assembly set starts to operate. |
| 4 | The back door closer motor is returned to the initial position and the latch switch is turned on. |
| 5 | After the power back door ECU detects a back door stop position pulse, the motor in the power back door unit assembly set is stopped. |
Opener Function 3 (Models with Hands Free Power Back Door Function)
When the kick door control sensor detects a kick operation, the opener function operates as follows:
| 1 | When a foot is brought near the kick door control sensor, the back door buzzer sounds for 0.8 seconds and the hazard warning lights blink twice.
Also, if the power back door is locked when a foot is brought near the kick door control sensor, the power back door unlocks. |
| 2 | The back door lock with courtesy light switch assembly (back door closer motor) releases the latch. |
| 3 | The back door courtesy switch is turned on and the motor in the power back door unit assembly set starts to operate. |
| 4 | The back door closer motor is returned to the initial position and the latch switch is turned on. |
| 5 | After the power back door ECU detects a back door stop position pulse, the motor in the power back door unit assembly set is stopped. |
Opener Function 4
When the power back door control switch or power back door button of the electrical key transmitter sub-assembly is operated, the opener function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | When the power back door control switch or power back door button of the electrical key transmitter sub-assembly is pressed while the back door is closing, the power back door buzzer sounds for approximately 0.2 seconds and the back door stops. |
| 2 | When the power back door control switch or power back door button of the electrical key transmitter sub-assembly is pressed for approximately 0.8 seconds again, the power back door buzzer sounds for approximately 0.8 seconds and the hazard warning lights flashes 2 times*. |
| 3 | The motor in the power back door unit assembly set starts to operate. |
| 4 | The power back door ECU detects a back door stop position pulse and the motor in the power back door unit assembly set stops. |
Opener Function 5
When the No. 1 power back door control switch is operated, the opener function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | When the No. 1 power back door control switch is pressed while the back door is closing, the power back door buzzer sounds for approximately 0.2 seconds and the back door stops. |
| 2 | When the No. 1 power back door control switch is pressed again, the power back door buzzer sounds for approximately 0.8 seconds and the hazard warning lights flashes 2 times*. |
| 3 | The motor in the power back door unit assembly set starts to operate. |
| 4 | The power back door ECU detects a back door stop position pulse and the motor in the power back door unit assembly set stops. |
Closer Function 1
When the power back door control switch or the power back door button of the electrical key transmitter sub-assembly is operated, the closer function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | After the power back door control switch or the power back door button of the electrical key transmitter sub-assembly is pressed for approximately 0.8 seconds, the power back door buzzer sounds for 0.8 seconds and the hazard warning light blinks twice*. |
| 2 | The motor in the power back door unit assembly set starts to operate. |
| 3 | When the latch switch is turned off, the voltage of the motor is reduced. |
| 4 | The back door lock with courtesy light switch assembly (back door closer motor) performs the closing operation 1 second after the latch switch is turned off, and stops the operation when the back door courtesy switch is turned off. |
Closer Function 2
When the No. 1 power back door control switch is operated, the closer function operates as follows:
|
*: Models with Power Back Door Hazard Warning Light |
|
| 1 | When the No. 1 power back door control switch is turned on, the power back door buzzer sounds for 0.8 seconds and the hazard warning light blinks twice*. |
| 2 | The motor in the power back door unit assembly starts to operate. |
| 3 | When the latch switch is turned off, the voltage of the motor is reduced. |
| 4 | The back door lock with courtesy light switch assembly (back door closer motor) performs the closing operation 1 second after the latch switch is turned off, and stops the operation when the back door courtesy switch is turned off. |
Closer Function 3 (Models with Hands Free Power Back Door Function)
When the kick door control sensor detects a kick operation, the closer function operates as follows:
| 1 | When a foot is brought near the kick door control sensor, the power back door warning buzzer sounds for 0.8 seconds and the hazard warning lights blink twice. |
| 2 | The motor in the power back door unit assembly set starts to operate. |
| 3 | When the latch switch is turned off, the voltage of the motor is reduced. |
| 4 | The back door lock with courtesy light switch assembly (back door closer motor) performs the closing operation 1 second after the latch switch is turned off, and stops the operation when the back door courtesy switch is turned off. |
FUNCTION
The power back door system has the following functions:
| Function | Outline |
|---|---|
|
*1: Models with wireless one motion function *2: Models with hands free power back door function |
|
| Opener Function | ·
Upon receiving an on signal from the power back door control switch or the back door opener switch assembly with the back door unlocked, the power back door ECU (multiplex network door ECU) actuates the back door closer motor and the power back door unit assembly set in order to release the latch of the back door and open the back door. |
| Closer Function | ·
Upon receiving an on signal from the power back door control switch, the No. 1 power back door control switch or the power back door button on the electrical key transmitter sub-assembly with the back door open, the power back door ECU (multiplex network door ECU) actuates the power back door unit assembly set and the back door closer motor in order to close the back door and engage the latch of the back door lock. |
| Hands Free Power Back Door Open Function*2 | When the back door is closed, the power back door ECU (multiplex network door ECU) releases the back door latch and opens the back door by operating the back door closer motor and power back door unit assembly when the ECU (multiplex network door ECU) receives a kick operation signal from the kick door control sensor. |
| Hands Free Power Back Door Close Function*2 | When the back door is open, the power back door ECU (multiplex network door ECU) closes the back door and engages the back door latch by operating the back door closer motor and power back door unit assembly when the ECU (multiplex network door ECU) receives a kick operation signal from the kick door control sensor. |
| Jam Protection Function | Upon receiving signals from a touch sensor or the Hall ICs of the power back door unit assembly set, when the power back door ECU detects that an object is jammed in the back door, the door operation is stopped after moving back a certain distance upward during the closing operation and suspended during the opening operation. The power back door buzzer sounds twice when a jammed object is detected. |
| Back Door Open/Close Speed Control Function | In accordance with the signals received from the Hall ICs, the power back door ECU performs control the opening and closing speeds of the back door. |
| Suspending Control Function | By conducting any of the following operations during the opening or closing operation of the power back door, the operation will be canceled:
·
The power back door system is turned off. ·
The power back door button on the electrical key transmitter sub-assembly is pressed. ·
The back door control switch is pressed. ·
The back door opener switch assembly is pressed. ·
The power back door control switch is pressed. ·
The No. 1 power back door control switch is pressed. ·
A kick operation is detected by the kick door control sensor.*2 |
| Memory Function | ·
By pressing the No. 1 power back door control switch for 2 seconds while holding the back door at the desired opening angle by hand, the power back door buzzer sounds 4 times as an answer back and the power back door ECU memorizes the angle. From the next time the back door is opened, the back door will stop at the set angle. ·
By pressing the No. 1 power back door control switch for 7 seconds after the set angle is memorized, the memorized position is initialized. |
| Assist Function | When the back door is stopped and then manually operated in the closing direction, the power back door ECU drives the power back door unit assembly set to operate the back door until it is fully closed. |
| Customization Function | By using the multi-information display, the following items can be customized.
·
Opening angle of the back door. ·
On/Off setting of the power back door system and hands free power back door function*2. ·
Volume of the power back door warning buzzer. |
| Switch Operation Function | When each operation switch is operated, the following operations are performed in accordance with the back door condition:
·
When the power back door control switch or the power back door button on the electrical key transmitter sub-assembly is pressed, opening the operation is performed when the back door is closed and the closing operation is performed when the back door is open. ·
When the back door opener switch assembly is pressed, the opening operation of the back door is performed. ·
When the No. 1 power back door control switch is pressed, the closing operation of the back door is performed. |
| Hands Free Operation Function*2 | ·
When a kick operation is detected by the kick door control sensor, the back door closes if open, and opens if closed. ·
When the back door is closing and a kick operation is detected by the kick door control sensor, the back door stops. ·
When the back door is closing and a kick operation is detected by the kick door control sensor, the back door stops. When another kick operation is detected, a back door close operation is performed. |
| Wireless One Motion Function*1 | ·
When the power back door button on the electrical key transmitter sub-assembly is pressed with the back door locked, the back door is unlocked and opened. ·
Although this function is disabled by default, the function can be set via the customization function. For details, refer to the Repair Manual. |
If the power supply is stopped such as when the cable is disconnected from the negative (-) terminal, initialization is required. The back door should be fully closed when performing initialization.