Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for HV Model) › from 2020.11
NM37A0E _58 Vehicle Interior _088156 THEFT DETERRENT / KEYLESS ENTRY _0420652 ENTRY AND START SYSTEM(for HV Model) CO CONTROL F

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for HV Model)  CONTROL  ENTRY AND START CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components for the start function have the following functions:

Component Function
Power Switch
·

Transmits the power switch signal to the certification ECU (smart key ECU assembly).

·

Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is too weak to respond to the tuner based on the signals from the room antennas.


Electrical Key Transmitter Sub-assembly Receives the signals from the antennas and returns the ID code to the electrical key and tire pressure warning ECU and receiver.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor), No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor), No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle.
Electrical Key and Tire Pressure Warning ECU and Receiver Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly).
Certification ECU (Smart Key ECU Assembly)
·

Certifies the ID code received from the electrical key and tire pressure warning ECU and receiver and transmits the certification results to the steering lock ECU (steering lock actuator or upper bracket assembly).

·

Transmits the steering wheel lock/unlock signals.

·

Transmits the immobiliser set/unset request signals.

·

Switches the power source ("ignition switch") among 4 modes (off, ACC, ON, start) in accordance with the shift position and the brake pedal signal.

·

Controls the entry and start system in accordance with the signals received from the switches and each ECU.


Stop Light Switch Assembly Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly).
Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) Receives the steering wheel unlock/lock request signal from the certification ECU (smart key ECU assembly), and activates the steering lock motor.
Combination Meter Assembly Multi Buzzer Sounds to inform the driver of malfunctions in the entry and start system.
Multi-information Display Informs the driver of power source or system abnormalities by displaying a warning message.


b.

The main components for the entry function have the following functions:

Component Function

*1: Models with power back door system

*2: Models with hands free power back door

Electrical Key Transmitter Sub-assembly
·

Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door antennas are received.

·

Outputs a request signal when the lock, unlock, panic, or power back door button on the electrical key transmitter sub-assembly is pushed.

·

Outputs information such as the key ID and vehicle ID when the radio wave signal that is output by the transponder key amplifier in the power switch is received.

·

Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.


Main Body ECU (Multiplex Network Body ECU)
·

Receives the request signal from the certification ECU (smart key ECU assembly), and actuates the door lock motors to unlock or lock all the doors.

·

Transmits the condition of each door to the certification ECU (smart key ECU assembly).


Certification ECU (Smart Key ECU Assembly)
·

Certifies the ID code received from the electrical key and tire pressure warning ECU and receiver and transmits the certification results to the steering lock ECU (steering lock actuator or upper bracket assembly).

·

Controls the antennas and lock/unlock sensor

·

Transmits the door lock/unlock request signals during the entry function.


Front Door Outside Door Handle Assembly Door Electrical Key Antenna Receives a request signal from the certification ECU (smart key ECU assembly) and creates an actuation area around the front doors.
Lock Sensor Transmits door lock request signals to the certification ECU (smart key ECU assembly).
Unlock Sensor Detects when a person touches the inside of an outside door handle.
Electrical Key Antenna (Outside Luggage Compartment) Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area around the back door.
No. 1 Indoor Electrical Key Antenna Assembly (Front Floor), No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor), No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle.
Electrical Key and Tire Pressure Warning ECU and Receiver Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly).
Combination Meter Assembly Multi Buzzer Sounds to inform the driver of malfunctions in the entry and start system.
Multi-information Display Informs the driver of power source or system abnormalities by displaying a warning message.
Wireless Door Lock Buzzer
·

Sounds as an answer back for entry lock/unlock and wireless lock/unlock to inform the driver.

·

Sounds to inform the driver of malfunctions in the entry and start system.


Power Back Door ECU (Multiplex Network Door ECU)*1 Controls the power back door system.
No. 1 Power Back Door Control Switch*1
·

Closes the back door when the No. 1 power back door control switch is pressed.

·

Outputs No. 1 power back door control switch signals to the power back door ECU (multiplex network door ECU).


Kick Door Control Sensor*2 Detects touchless kick actuation operations and outputs signals to the power back door ECU.



OPERATION


a.

The special functions of the entry and start system only work when the electrical key transmitter sub-assembly is in the actuation area formed by the antennas.


b.

The No. 1, No. 2 and No. 3 indoor electrical key antenna assemblies form the actuation area of the start function.


c.

The door electrical key antennas and the electrical key antenna form the actuation area of the entry function.

Y259914C01
2.167,2.25 2.333,2.25 2.333,2.25 2.969,1.458 true 4.333,2.333 4.167,2.333 4.167,2.333 3.354,1.458 true 4.948,2.26 4.781,2.26 4.781,2.26 4.177,1.458 true 5.615,1.948 5.448,1.948 5.448,1.948 4.865,1.313 true 3.917,2.583 3.75,2.583 3.75,2.583 3.302,2.021 true 3.833,0.167 3.667,0.167 3.667,0.167 3.323,0.76 true 2.25,2.583 2.604,2.583 2.604,2.583 2.917,2.333 true 2.281,0.24 2.635,0.24 2.635,0.24 2.948,0.406 true 5.885,0.469 5.552,0.469 5.552,0.469 5.302,0.969 true 5.927,0.375 6.24,0.573 0.313,0.198 10 false *a 2.073,0.125 2.385,0.323 0.313,0.198 10 false *a 2.073,2.479 2.385,2.677 0.313,0.198 10 false *a 1.979,2.135 2.292,2.344 0.313,0.208 10 false *1 4.375,2.24 4.688,2.448 0.313,0.208 10 false *2 4.99,2.156 5.302,2.365 0.313,0.208 10 false *3 5.646,1.833 5.958,2.042 0.313,0.208 10 false *4 3.948,2.49 4.26,2.698 0.313,0.208 10 false *5 3.875,0.063 4.188,0.271 0.313,0.208 10 false *6
*1 No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) *2 No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)
*3 No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) *4 Electrical Key Antenna (Outside Luggage Compartment)
*5 Front Door Outside Handle Assembly LH
·

Door Electrical Key Antenna


*6 Front Door Outside Handle Assembly RH
·

Door Electrical Key Antenna


*a Approximately 0.7 m to 1.0 m (2.3 ft. to 3.3 ft.) - -
V100145

Interior Actuation Area
V100144

Exterior Actuation Area


Actuation Area Detail

*: Models with hands free power back door

Interior The interior actuation area of the indoor electrical key antennas (front, center, rear) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when a lock sensor is on.
Exterior The exterior actuation area formed by the front door electrical key antennas (LH, RH) and electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside door handle or the center of the rear bumper.
Around Front Doors The exterior actuation area of the door electrical key antennas is formed by transmitting a request signal every 0.25 seconds while the ignition switch is off and each door is locked. In this way, the presence of an electrical key transmitter sub-assembly is detected. When locking the door using the lock sensor on the outside door handle, the actuation area is formed when the lock sensor is touched.
Around Back Door The exterior actuation area of the electrical key antenna is formed when the back door lock or back door unlock switch is on.*



SYSTEM CONTROL


a.

Start Function

i.

The start function has different power source change patterns to suit the brake pedal state and shift lever position.

Pattern Brake Pedal Shift Lever Position Power Source Change Pattern
A Depressed P When the power switch is pushed once.
·

Off → ON (after hybrid system is started)


B Not Depressed P Each time the power switch is pushed.
·

Off → ACC → ON → off


C Except P Each time the power switch is pushed.
·

Off → ACC → ON → ACC


D - P When the power switch is pushed in the ON condition.
·

ON (hybrid system is started or not started) → off


E - Except P When the power switch is pushed in the ON condition.
·

ON (hybrid system is started or not started) → ACC



Y218338E03
0.115,0.094 3.198,0.448 3.083,0.354 12 false Transition of Power Source Modes: 0.208,0.583 1.531,0.823 1.323,0.24 10 false Shift Lever Position 0.583,0.979 1.24,1.229 0.656,0.25 10 false Pattern 0.375,1.375 1.406,1.583 1.031,0.208 10 false Power Switch 0.417,1.771 1.281,2.021 0.865,0.25 10 false Brake Pedal 0.625,2.177 1.229,2.438 0.604,0.26 10 false Time 0.104,3.146 0.563,3.688 0.458,0.542 10 false Power Source 0.948,2.615 1.302,2.823 0.354,0.208 10 false Off 0.771,3.01 1.51,3.271 0.74,0.26 10 false On (ACC) 0.823,3.417 1.531,3.677 0.708,0.26 10 false On (IG) 0.813,3.823 1.448,4.073 0.635,0.25 10 false READY 3.333,0.573 3.802,0.813 0.469,0.24 10 false P 5.823,0.573 6.583,0.854 0.76,0.281 10 false Except P 1.917,0.979 2.677,1.26 0.76,0.281 10 false B or D 3.25,0.979 4.01,1.26 0.76,0.281 10 false A or D 1.885,1.375 2.646,1.656 0.76,0.281 10 false Pushed 3.104,1.792 3.865,2.073 0.76,0.281 10 false Depressed 5.406,0.969 6.167,1.25 0.76,0.281 10 false C or E 4.615,0.948 5.031,1.188 0.417,0.24 10 false - 4.625,1.365 5.042,1.604 0.417,0.24 10 false - 4.625,1.75 5.042,1.99 0.417,0.24 10 false - 5.573,1.75 5.99,1.99 0.417,0.24 10 false - 6.521,0.958 6.938,1.198 0.417,0.24 10 false - 6.229,1.792 6.99,2.073 0.76,0.281 10 false Depressed 5.563,2.167 5.979,2.406 0.417,0.24 10 false - 6.552,2.167 6.969,2.406 0.417,0.24 10 false - 2.063,1.75 2.479,1.99 0.417,0.24 10 false - 2.063,2.167 2.479,2.406 0.417,0.24 10 false - 3.396,2.167 3.813,2.406 0.417,0.24 10 false - 4.25,2.188 4.51,2.417 0.26,0.229 10 false *1 4.563,2.188 4.823,2.417 0.26,0.229 10 false *2 4.885,2.188 5.146,2.417 0.26,0.229 10 false *3 3.208,1.385 3.969,1.667 0.76,0.281 10 false Pushed 5.365,1.385 6.125,1.667 0.76,0.281 10 false Pushed 6.323,1.385 7.083,1.667 0.76,0.281 10 false Pushed 5.542,3.042 5.802,3.271 0.26,0.229 10 false # 5.844,3.042 6.104,3.271 0.26,0.229 10 false # 6.813,3.031 7.073,3.26 0.26,0.229 10 false # 0.646,4.417 2.479,4.615 1.833,0.198 10 false : Transition 0.635,4.813 3.719,5.063 3.083,0.25 10 false : Only when key certification is OK. 0.656,5.198 6.531,5.865 5.875,0.667 10 false : Only when the vehicle is stopped. (While driving, if the power switch is pressed for 2 seconds or more or pressed 3 times or more in a row, the hybrid system is stopped and the power source mode changes to on (ACC).) 0.646,6.146 6.906,6.552 6.26,0.406 10 false : Power source transition to off is possible only when the power source mode has changed to on (ACC), such as the power source transition indicated by #, and the shift lever has been moved to P. 0.313,6.833 3.396,7.083 3.083,0.25 10 false *1: Not operated for 20 minutes 0.313,7.167 2.729,7.417 2.417,0.25 10 false *2: Not operated for 1 hour 0.313,7.5 5.146,7.75 4.833,0.25 10 false *3: Power source turned off according to hybrid system request

NOTICE:
·

Normally, the operation of the power switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the power switch for approximately 2 seconds or more or pushing the power switch 3 times or more in a row, the driver can stop the hybrid system while the vehicle is in motion.

·

If no signals are transmitted to the certification ECU (smart key ECU assembly) due to malfunctions in the stop light switch assembly, the hybrid system may not start when the power switch is pushed with the brake pedal depressed. In such cases, performing the following procedure may enable the hybrid system to start: 1) push the power switch to turn the power source from off to ACC, and 2) push the power switch again and hold it for 15 seconds or more.

·

The above 2 operations must be applied only in emergency situations. Under normal conditions, the hybrid system must not be stopped by pushing the power switch while driving. Also, it should not be started without depressing the brake pedal or when a shift state other than park (P) has been selected





b.

Entry Unlock

i.

When the electrical key transmitter sub-assembly is in the actuation area formed by the door electrical key antenna, holding the outside door handle assembly of the driver seat and touching the built-in touch sensor unlocks the driver door only, and holding any of the passenger side outside handle assemblies and touching the built-in touch sensor unlocks all the doors. (Driver door mode)


ii.

When the electrical key transmitter sub-assembly is in the actuation area formed by the door electrical key antenna, holding any of the outside door handle assemblies and touching the built-in touch sensor unlocks all the doors. (All door mode)


iii.

When the doors are unlocked, the hazard warning lights flash twice and the buzzer sounds twice as an answer back.

HINT:

If the doors are locked by wireless operation, the entry and start system or key linked power door lock operation, it may not be possible to unlock the doors using the entry and start system. In this situation, use the wireless function of the electrical key transmitter sub-assembly to unlock the doors.


Y259915C01
2.667,0.417 2.833,0.417 2.833,0.417 3.5,1 true 2.469,0.302 2.781,0.5 0.313,0.198 10 false *a
*a Unlock Sensor (Backside) - -




c.

Entry Lock

i.

When the electrical key transmitter sub-assembly is in any of the exterior actuation areas, all doors are locked by touching the lock sensor of the front outside door handle assembly or by pressing the back door lock switch of the back door.


ii.

After all doors have been locked, the wireless door lock buzzer sounds once as an answer back and the hazard lights flash once at the same time.

Y259916C01
2.667,0.25 3.146,0.542 false 2.5,0.25 2.667,0.25 2.667,0.25 3.146,0.74 false 2.313,0.135 2.625,0.333 0.313,0.198 10 false *a
*a Lock Sensor - -



iii.

When the electrical key transmitter sub-assembly is in the back door exterior actuation area with all the doors closed, all doors are locked by pressing the back door lock switch.

Y259918C01
3.781,2.188 3.781,1.938 3.781,1.938 3.948,1.938 false 3.719,1 4.031,1.198 0.313,0.198 10 false *a 3.969,1.833 4.281,2.031 0.313,0.198 10 false *1
*1 Back Door Opener Switch Assembly (Lock Switch) - -
*a 0.3 m (0.984 ft.) - -




d.

Entry Back Door Unlock Function

i.

When the electrical key transmitter sub-assembly is in the actuation area surrounding the back door, pressing the back door unlock switch will unlock the back door.

Y259917C01
3.594,2.177 3.594,1.927 3.594,1.927 3.76,1.927 false 3.792,1.823 4.104,2.021 0.313,0.198 10 false *1 3.688,0.99 4,1.188 0.313,0.198 10 false *a
*1 Back Door Opener Switch Assembly (Open Switch) - -
*a 0.7 to 1 m (2.30 to 3.28 ft.) - -




e.

Reserve Lock Function (Models with power back door system)

i.

When a door other than the power back door is closed and the door lock is operated by lock sensor of door outside handle within the exterior actuation area during back door auto close operation, a door lock operation is performed at that time. The door lock operation completes when the back door close operation ends.



f.

Hands Free Power Back Door Function (Models with hands free power back door)

i.

When the electrical key is in the actuation area surrounding the back door, performing a touchless kick actuation operation towards the center of the rear bumper will open or close the back door.

Y259508C01
3.021,3.156 2.667,3.74 2.667,3.74 2.5,3.74 true 4.115,3.927 3.979,3.667 true 3.802,4.042 3.698,3.75 true 2.354,3.667 2.667,3.823 0.313,0.156 10 false *1 4.115,3.948 4.427,4.104 0.313,0.156 10 false *b 3.75,4.063 4.063,4.219 0.313,0.156 10 false *c 5,4.115 5.313,4.271 0.313,0.156 10 false *a 3.063,3.479 3.375,3.635 0.313,0.156 10 false *d
*1 Kick Door Control Sensor - -
*a The user carrying an electrical key stands around the center of the rear bumper while maintaining a certain distance (approximately equal to the length of the arm) from the rear bumper. *b The user waves a foot within approximately 100 mm (3.94 in.) from the surface of the rear bumper.
*c The user moves the foot away from the surface of the rear bumper. *d Approximately 100 mm (3.94 in.)




g.

Warning

i.

When any of the situations below occur, the entry and start system sounds the wireless door lock buzzer and a buzzer in the combination meter assembly and displays a message on the multi-information display in order to alert the driver.

Situation Condition
A The hybrid system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
B The hybrid system is left running and the shift lever is in P when the driver gets out of the vehicle.
C The hybrid system is left running when a passenger gets out of the vehicle while holding the electrical key transmitter sub-assembly.
D The electrical key transmitter sub-assembly is not within the actuation areas.
E The vehicle is driven without an electrical key transmitter sub-assembly.
F The electrical key transmitter sub-assembly is left in the vehicle.
G A door is ajar.
H The key reminder sounds.
I The key battery is weak.
J Steering lock does not release.
K A malfunction has been detected in a vehicle speed signal, etc.
L The hybrid system cannot be started (system/driver error).
M Immobiliser system certification confirmation occurs.
N An electrical key transmitter sub-assembly has been registered to the vehicle.
O Hybrid system start operation guide ACC
P Hybrid system start operation guide ON
Q The ignition switch cannot be turned off (shift lever in any position except P).
R The ignition switch cannot be turned off (shift lever in P).
S Auto power off operation occurs.
T Hybrid system emergency stop operation is performed.
U The user performed an emergency engine stop while driving.
V Power switch is operated while driving.
W Power switch is operated while driving.
X While the vehicle is stationary, the shift lever is moved to a position other than P or N with the ignition switch ON and the hybrid system stopped.
Y While the vehicle is stationary, with a shift position N selected, the ignition switch ON and the hybrid system stopped.
Z The vehicle started to roll away with the ignition switch ON and the hybrid system stopped.
AA Accessory state
AB Ignition on state


ii.

Situation A

There are 2 patterns for situation A.

Pattern 1:

When the shift lever is in a position other than P, the power switch is in a mode other than off and the driver opens the door and attempts to get out of the vehicle, the following control is performed:

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away (vehicle creep, such as when N is selected)
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC or ON.

·

The shift lever is in any position except P.

·

The driver door is opened.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

"Shift to P Before Exiting Vehicle"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The shift lever is moved to P.

·

The driver door is closed.

·

The vehicle speed is above 5 km/h (3 mph).



Pattern 2:

Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly. In this situation, the following control is performed:

Possible Effects without Warning Sudden vehicle movement, vehicle theft, vehicle roll-away
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC or ON.

·

The shift lever is in any position except P.

·

The driver door is opened → closed.

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display The following warning messages are alternately displayed:
·

"Shift to P Before Exiting Vehicle"

·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer Sounds continuously
Buzzer and Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).


"Shift to P Before Exiting Vehicle" Message Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).





iii.

Situation B

There are 3 patterns for situation B.

Pattern 1:

When the shift lever is in P and the power switch is in a mode other than off (the steering remains unlocked), the driver door is opened and the driver attempts to leave the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC.

·

The driver door is open.


Condition 2
The warning is activated when all of the following conditions are met for 1 second:
·

The ignition switch is turned off.

·

The steering lock remains unlocked.

·

The driver door is open.


Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously at short and even intervals
Multi-information Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned to ON.

·

The driver door is closed.

·

The ignition switch is turned off and the steering wheel lock control is performed.



Pattern 2:

Under the situation of pattern 1, the driver opens and closes the driver door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC or ON.

·

The shift lever is in P.

·

The driver door is opened → closed.

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer Sounds 8 times
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).



Pattern 3:

Under the situation of pattern 2, the driver touches the lock sensor on the door outside handle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC or ON.

·

The shift lever is in P.

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails), but detected in an outside detection area (exterior key certification result is OK).

·

The lock sensor on the outer door handle is on (touched).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning messages are alternately displayed:
·

"Turn Off Vehicle"

·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following condition is met:
·

5 seconds elapse.

·

The ignition switch is turned off.

·

The shift lever is moved to any position except P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).

·

Any door is opened or closed.


"Turn off Vehicle" Message Warning Stop Condition The warning is stopped when any of the following condition is met:
·

60 seconds elapse.

·

The ignition switch is turned off.

·

The shift lever is moved to any position except P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).





iv.

Situation C

When the hybrid system is left running, a passenger leaves the vehicle while holding the electrical key transmitter sub-assembly. In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ACC or ON.

·

A door other than the driver door is opened → closed.

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer Sounds 8 times
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).





v.

Situation D

When the electrical key transmitter sub-assembly is not in the vehicle, the driver attempts to turn the ignition switch to ON (emergency key operation* is included). In this situation, the following control is performed:

*: Emergency key operation is an operation that changes the power source by touching the power switch with the electrical key transmitter sub-assembly.

Possible Effects without Warning User becomes confused
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The immobiliser system is set.

·

The electrical key transmitter sub-assembly is not in the vehicle (interior key certification fails and transponder certification fails).

·

No records of unlock operation using a mechanical key and key certification failure when the ignition switch was turned to ON.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

15 seconds elapse.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since a door was opened using a door outside door handle.





vi.

Situation E

The vehicle starts moving without a registered electrical key transmitter sub-assembly in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is ON.

·

The warning is activated in situation C.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails).


Warning Method Combination Meter Assembly Multi Buzzer Sounds 9 times
Multi-information Display The following warning message is displayed:
·

"Key Not Detected Check Key Location"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The ignition switch is turned off.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).





vii.

Situation F

The lock sensor on a door outside handle is touched to perform entry lock with the electrical key transmitter sub-assembly left in the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is off.

·

All doors are closed.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK).

·

The lock sensor on the outer door handle is on (touched).

·

Any door is unlocked.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Key Detected in Vehicle"


Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

5 seconds elapse.

·

The ignition switch is turned to ACC or ON.

·

The vehicle speed is above 5 km/h (3 mph).

·

Any door is opened.

·

Lock operation is detected.


"Key detected in vehicle" Message Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

60 seconds elapse.

·

The ignition switch is turned to ACC or ON.

·

The vehicle speed is above 5 km/h (3 mph).

·

Lock operation is detected.





viii.

Situation G

The lock sensor on the door outside handle is pushed to perform entry lock, however, a door is ajar. In this situation, the following control is performed:

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is off.

·

Any door is open other than the door where the entry lock operation is performed.

·

The lock sensor on the outer door handle is on (touched), the lock button on the electrical key transmitter sub-assembly or the back door lock switch is pressed.

·

The electrical key transmitter sub-assembly is in an outside detection area (exterior key certification result is OK).


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display -
Wireless Door Lock Buzzer Sounds continuously
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

5 seconds elapse.

·

The ignition switch is turned to ACC or ON.

·

All doors are closed.

·

Unlock operation is performed using the wireless door lock remote function.

·

Unlock operation is performed using the touch sensor on the inside of an outer door handle.





ix.

Situation H

The door is locked with the electrical key transmitter sub-assembly left in the vehicle. In this situation, the following control is performed:

*: Keyless lock operation is door lock operation without using the electrical key transmitter sub-assembly. First, set the lock position (door lock knob) when the door is open, and close the door while pulling the door handle to lock the door.

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The door is locked using the keyless lock operation.*

·

The electrical key transmitter sub-assembly is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Key Detected in Vehicle"


Wireless Door Lock Buzzer Sounds continuously
Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following condition is met:
·

5 seconds elapse.

·

The power switch is turned to other mode.

·

Any door is opened.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Left inside Vehicle" Message Warning Stop Condition The warning is stopped when any of the following condition is met:
·

60 seconds elapse.

·

The power switch is turned to another mode.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).





x.

Situation I

The vehicle is driven using an electrical key transmitter sub-assembly that has a low battery. In this situation, the following control is performed:

*: Warning performed after 20 minutes of the ignition switch being turned to ON

Possible Effects without Warning Usability function, hybrid system cannot be restarted
Warning Active Condition Condition 1
The warning is activated when all of the following conditions are met:
·

The ignition switch is turned off after being left ON for more than 20 minutes.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key transmitter sub-assembly is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2
The warning is activated when all of the following conditions are met:
·

The hybrid system is stopped → restarted.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key transmitter sub-assembly is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.

·

The low key battery warning for condition 1 was performed.*


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Key Battery Low"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

15 seconds elapse.

·

The vehicle speed is above 5 km/h (3 mph).





xi.

Situation J

The steering lock cannot be released or the shift lever is moved to a position other than P before the steering lock is unlocked. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the following condition is met:
The steering lock cannot be released (the steering lock ECU judgment).
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Push Power Switch while Turning the Steering Wheel in Either Direction"


Wireless Door Lock Buzzer -
Warning Stop Condition The power switch is pushed while the steering wheel is turned left and right.
The warning is stopped when any of the following condition is met:
·

15 seconds elapse.

·

The steering lock is released.





xii.

Situation K

A vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator or upper bracket assembly) operation has been detected. In this situation, the following control is performed:

Possible Effects without Warning Malfunction detection
Warning Active Condition The warning is activated when any of the following condition is met:
·

The steering lock ECU (steering lock actuator or upper bracket assembly) or steering lock/unlock position switch is malfunctioning.

·

The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Smart Entry & Start System Malfunction See Owner's Manual"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

15 seconds elapse.

·

The system returns to normal.





xiii.

Situation L

When the driver attempts to start the hybrid system after unlocking the driver door using the mechanical key, the electrical key transmitter sub-assembly cannot be detected in the vehicle or cannot be detected in the vehicle 2 times in a row. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the power switch is pressed with any of the following conditions met:
·

The immobiliser system is set.

·

The electrical key transmitter sub-assembly is not detected in the vehicle (interior key certification fails).

·

The doors were unlocked using a mechanical key or when the power switch is pressed, a certification error occurs 2 times in a row.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed for 60 seconds (and then automatically turned off):
·

"Press Brake Pedal and Touch Power Switch with Key"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

60 seconds elapse.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since the door was opened using a door outside door handle.





xiv.

Situation M

The power switch is touched with an electrical key transmitter sub-assembly when the transmitter battery voltage is low, smart operation is canceled or radio interference occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition Transponder certification result is OK.
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Press brake and power to start"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

10 seconds elapse.

·

The electrical key transmitter sub-assembly is detected in the vehicle (interior key certification results is OK).

·

The hybrid system is started.

·

The immobiliser system is set and interior certification is stopped or key certification fails.





xv.

Situation N

An electrical key transmitter sub-assembly has been registered to the vehicle. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The ignition switch is turned off.

·

The driver door is unlocked by an unlock operation from the outside of the vehicle, and then opened.


Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"A New Key has been Registered Contact Your Dealer for Details"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

60 seconds have elapsed since the warning started.

·

All doors are closed and locked.

·

The ignition switch is turned off.





xvi.

Situation O

The system recognizes the situation that indicates the driver may start the hybrid system (when the driver enters the vehicle or the ignition switch is ACC). In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted
Warning Active Condition The warning is activated when any of the following condition is met:
·

When the door is unlocked from the outside of the vehicle with the ignition switch off, the driver door is closed → opened.

·

Each time the power source mode is changed from off to ACC without the brake pedal depressed.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Press brake and power to start"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

19 seconds have elapsed since the warning started.

·

The hybrid system is started.

·

Door lock operation is performed from the outside of the vehicle.

·

Wireless operation is performed from the inside of the vehicle or door lock operation is performed using a keyless lock function.





xvii.

Situation P

The system recognizes the situation that indicates the driver may start the hybrid system (when the ignition switch is ON). In this situation, the following control is performed:

Possible Effects without Warning Hybrid system cannot be restarted
Warning Active Condition The warning is activated when any of the following condition is met:
·

Each time the power source mode is changed from off to ON (the hybrid system is not started) with the shift lever in P and without the brake pedal depressed.

·

When the ignition switch is ON (the hybrid system is not started) with the shift lever in a position other than P, the shift lever is moved to P.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Press brake and power to start"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The power source mode is changed to any mode other than ON.

·

The vehicle speed is above 5 km/h (3 mph).

·

The shift lever is in a position other than P.





xviii.

Situation Q

The driver attempts to turn the ignition switch off with the shift lever in any position other than P. In this situation, the following control is performed:

Possible Effects without Warning Discharged vehicle auxiliary battery, vehicle roll-away.
Warning Active Condition The ignition switch is turned off when the shift lever in a position other than P. (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.)
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Shift to P Before Exiting Vehicle"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to P.

·

The ignition switch is turned to a mode other than ACC.





xix.

Situation R

Under situation P, the shift lever is moved to P. In this situation, the following control is performed:

Possible Effects without Warning Discharged vehicle auxiliary battery.
Warning Active Condition The shift lever is moved to P.
Warning Method Combination Meter Assembly Multi Buzzer Sounds once
Multi-information Display The following warning message is displayed:
·

"Turn Off Vehicle"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The power source mode is changed to a mode other than ACC.

·

The shift lever is in any position other than P.





xx.

Situation S

Automatic power off operation occurs. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The shift lever is in P.

·

The ignition switch is ACC or ON.

·

The vehicle speed is not detected and the hybrid system is stopped.

·

The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the ignition switch ACC or for 1 hour with the ignition switch ON).


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Auto Power Off to Conserve Battery"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

10 seconds have elapsed since the warning started.

·

The ignition switch is turned to ACC or ON.





xxi.

Situation T

The driver stopped the hybrid system using emergency operation while driving. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when any of the following condition is met:
·

The hybrid system is stopped by emergency stop operation while driving.

·

After emergency stop operation, the ignition switch is turned to ON, the vehicle speed is detected and the hybrid system is not started.


Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Shift to N and Push POWER Switch to Restart"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to P.

·

The vehicle speed is not detected (after the ignition switch is turned to ON using power switch operation).

·

The power switch is operated.

·

The hybrid system has started.





xxii.

Situation U

The user performed an emergency hybrid system stop while driving. In this situation, the following control is performed:

Possible Effects without Warning The driver may not notice that the hybrid system has been stopped while driving.
Warning Active Condition The hybrid system is stopped using the emergency engine stop function.
Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
Multi-information Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to P.

·

The vehicle speed is not detected (after the ignition switch is turned to ON using power switch operation).

·

The hybrid system has started.





xxiii.

Situation V

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Wrong operation is prevented
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Multi Buzzer Sounds intermittently
Multi-information Display -
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

1.8 seconds have elapsed since the power switch operation was stopped.

·

The ignition switch is turned off.





xxiv.

Situation W

The driver pressed the power switch while driving. In this situation, the following control is performed:

Possible Effects without Warning Wrong operation is prevented
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the power switch is pressed.
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display The following warning message is displayed:
·

"Push and Hold Power Switch for Emergency Stop"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

10 seconds elapse.

·

The ignition switch is turned off.





xxv.

Situation X

While the vehicle is stationary, the shift lever is moved to a position other than P or N with the ignition switch ON and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is stopped, the shift lever is moved to a position other than P or N with the ignition switch ON.
Warning Method Combination Meter Assembly Buzzer Sounds continuously
Multi-information Display The following warning message is displayed:
·

"Hybrid System Stopped Shift into P"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to P or N.

·

The ignition switch is turned off.

·

The vehicle speed is detected.





xxvi.

Situation Y

While the vehicle is stationary, the shift lever is moved to a position N with the ignition switch ON and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition While the vehicle is stopped, the shift lever is moved to a position N with the ignition switch ON.
Warning Method Combination Meter Assembly Buzzer -
Multi-information Display The following warning message is displayed:
·

"Shift to P to Start"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to other than N.

·

The ignition switch is turned off.

·

The vehicle speed is detected.





xxvii.

Situation Z

The vehicle started to roll away with the ignition switch ON and the hybrid system stopped. In this situation, the following control is performed:

Possible Effects without Warning Vehicle roll-away
Warning Active Condition While the vehicle is moving, the shift lever is in a position other than P or N with the ignition switch ON and the hybrid system stopped.
Warning Method Combination Meter Assembly Buzzer Sounds intermittently
Multi-information Display The following warning message is displayed:
·

"Hybrid System Stopped Stop in a Safe Place"


Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The shift lever is moved to N.

·

The ignition switch is turned off.

·

The hybrid system has started.

·

The vehicle speed is not detected.





xxviii.

Situation AA

The power source is changed to ACC. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to ACC.
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display "ACCESSORY"
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when the following condition is met:
·

The power source is changed to a mode other than ACC.





xxix.

Situation AB

The power source is changed to ON. In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to ON.
Warning Method Combination Meter Assembly Multi Buzzer -
Multi-information Display "IGNITION ON"
Wireless Door Lock Buzzer -
Warning Stop Condition The warning is stopped when any of the following condition is met:
·

The power source is changed to a mode other than ON.

·

The display in the odometer area is changed due to user operation.






h.

Auxiliary Battery Saving

i.

Auxiliary battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key transmitter sub-assembly is left in the exterior actuation area.

Condition Control Reinstatement Condition
When the vehicle remains parked for a long time. Control 1:
No response from electrical key transmitter sub-assembly for more than 5 days
·

Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.


When the ignition switch is turned to ON, the control is canceled and the system is returned to normal.
Control 2:
No response from electrical key transmitter sub-assembly for more than 14 days
·

Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.

·

Door lock sensors and unlock sensors for seats other than the driver seat are disabled.


When the ignition switch is turned to ON, the control is canceled and the system is returned to normal.
when any of the following condition is met, the control is returned to control 1:
·

The doors are locked or unlocked using wireless remote control.

·

The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.

·

A door is locked or unlocked using the mechanical key.

·

Door is opened → closed.


When the electrical key transmitter sub-assembly is left in the exterior detection area. This state continues longer than 10 minutes
·

Electrical key antenna that is detecting the electrical key transmitter sub-assembly stops emitting signals for creating the actuation area.


The control is stopped when any of the following condition is met:
·

The doors are locked or unlocked using wireless remote control.

·

The doors are locked or unlocked by touching the lock/unlock sensor on the front door.

·

A door is locked or unlocked using the mechanical key.




ii.

In addition to the above functions, the auto power off function helps to reduce drain on the vehicle auxiliary battery by turning the power source mode to off when approximately 60 minutes have elapsed since the shift lever was moved to P with the power source ACC, or the hybrid system was turned off with the shift lever in P, the power source ON and the vehicle stationary.



i.

Auxiliary Battery Saving Function of Electrical Key Transmitter Sub-assembly

i.

This function cancels the signal reception waiting state of the electrical key transmitter sub-assembly, reducing the consumption of current from its auxiliary battery.


ii.

The electrical key transmitter sub-assembly can be placed into and taken out of auxiliary battery saving mode. When the electrical key transmitter sub-assembly is in auxiliary battery saving mode, the entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The function of the entry and start system will not operate if the electrical key transmitter sub-assembly is in auxiliary battery saving mode.


iii.

Pressing the unlock button of the electrical key transmitter sub-assembly twice while pressing the lock button (the indicator light of the electrical key transmitter sub-assembly blinks 4 times) selects auxiliary battery saving mode for the electrical key transmitter sub-assembly.


iv.

Auxiliary battery saving mode can be canceled by pressing any switch on the electrical key transmitter sub-assembly.



j.

Entry Unlock Mode Switching Function (Manual Operation)

i.

The following entry unlock modes can be selected when using the entry unlock mode switching function.

·

All door unlock mode: When the sensor of a door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

·

Driver door unlock mode (Default): When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.



ii.

When customizing through manual operation:

1.

Turn the ignition switch off.

2.

Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.

3.

Check the current setting.

HINT:
·

The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

·

The answer back (wireless door lock buzzer, multi buzzer in the combination meter assembly) operation for each mode is indicated in the table below.



Currently Selected Mode Answer back (Wireless Door Lock Buzzer) Answer back (Multi Buzzer in Combination Meter Assembly)
All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once

4.

Release the lock and unlock buttons of the electrical key transmitter sub-assembly.

5.

Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

HINT:

Repeat the procedure as necessary to select the desired mode.


6.

Unlock the doors with the wireless operation, and then open any door.

Y191645E01
0.323,1.74 1.229,2.125 0.906,0.385 10 false Driver Door 0.365,2.865 1.271,3.25 0.906,0.385 10 false All Doors 1.677,0.594 3.573,1.073 1.896,0.479 10 false Wireless Door Lock Buzzer 4.594,0.292 6.781,0.948 2.188,0.656 10 false Combination Meter Assembly 4.323,0.906 6.135,1.458 1.813,0.552 10 false Multi-information Display 6.469,0.906 7.073,1.344 0.604,0.438 10 false Buzzer 4.875,1.656 6.083,2.448 1.208,0.792 10 false Driver door "OPEN" indication 4.906,2.76 6.042,3.302 1.135,0.542 10 false All doors "OPEN" indication 1.969,2.125 3.281,2.531 1.313,0.406 10 false Sounds 3 times 1.979,3.198 3.208,3.573 1.229,0.375 10 false Sounds 2 times 1.448,2.771 1.896,3 0.448,0.229 10 false ON 1.344,1.927 1.74,2.354 0.396,0.427 10 false OFF 6.448,2.219 6.938,2.885 0.49,0.667 10 false Sounds once 1.417,1.667 1.906,1.885 0.49,0.219 10 false ON 1.396,3.031 1.896,3.344 0.5,0.313 10 false OFF




k.

Key Cancel

i.

The following system functions can be deactivated by using the key cancel procedure.

·

Entry Lock

·

Entry Unlock

·

Back Door Open

·

Prevention of Key Confinement

·

Warning



ii.

The system functions can be deactivated by using the following key cancel procedure when the ignition switch is off and the driver door is closed and unlocked.

*: Perform all these 3 steps within 30 seconds of the previous step.

Key Cancel Procedure The procedure is as follows:
·

Press the unlock switch of the electrical key transmitter sub-assembly once.

·

Within 5 seconds of the step above, open the driver door (Driver Door: Close → Open).

·

Within 5 seconds of the step above, press the unlock switch of the electrical key transmitter sub-assembly twice.

·

Repeat close → open for the driver door twice* (Driver Door: Open → Close → Open → Close → Open).

·

Press the unlock switch of the electrical key transmitter sub-assembly twice.*

·

Repeat close → open for the driver door once* (Driver Door: Open → Close → Open).

·

Within 5 seconds of the step above, close the driver door.


When the cancel procedure is complete, the buzzer sounds twice. Meanwhile, when the procedure is performed again to resume the system, the buzzer sounds once.



l.

Key Code Registration Function

i.

The table below shows the 3 special ID code registration function modes through which up to 7 different transmitter recognition codes can be registered. For details, refer to the Repair Manual.

Mode Function
Rewrite Clears all previously registered codes and registers only the newly received codes. This mode is used whenever the certification ECU (smart key ECU assembly) is replaced.
Add Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter.
Confirm Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.




FUNCTION


a.

Entry Function

i.

The entry function consists of the following functions:

Function Outline
Wireless Door Lock Control This function is a convenient system for locking and unlocking all the doors at a distance. The operation of this function is the same as that in the wireless door lock control system.
Entry Illumination When an electrical key transmitter sub-assembly enters the exterior actuation area of the door electrical key antennas, the interior light illuminates.
Entry Unlock When an electrical key transmitter sub-assembly is located in the exterior actuation area of any door electrical key antenna, the door will unlock after the inner part of an outside door handle is touched.
Entry Unlock Mode Switching Allows switching between 2 modes that can be operated with the entry unlock function.
·

Driver Door Mode

·

All Door Mode


Entry Lock When an electrical key transmitter sub-assembly is located in the exterior actuation area of an electrical key antenna and the ignition switch is off, all doors can be locked by simply touching the lock sensor or pressing the back door lock switch.
Entry Back Door Unlock The back door is unlocked by pressing the back door unlock switch of the back door.
Prevention of Key Confinement The key confinement prevention function prevents the vehicle from being locked with an electrical key transmitter sub-assembly left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor).
Warning When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound the multi buzzer in the combination meter and the wireless door lock buzzer, and indicates a warning on the multi-information display in order to alert the driver.
·

An exit warning is activated if the shift lever is in any position other than P.

·

An exit warning is activated if the shift lever is in P and the power switch is in a mode other than off.

·

A warning is activated if the occupant leaves with the electrical key transmitter sub-assembly in inappropriate circumstances.

·

A warning is activated if the power switch is operated while the electrical key transmitter sub-assembly is outside the actuation area.

·

A warning is activated if the lock button is operated while the electrical key transmitter sub-assembly is inside the vehicle.

·

A warning is activated if the key battery is weak.


Auxiliary Battery Saving To prevent the electrical key transmitter sub-assembly auxiliary battery and the vehicle auxiliary battery from becoming discharged, the auxiliary battery saving function activates when the vehicle remains unused for a long period of time or the electrical key transmitter sub-assembly has been detected in the exterior actuation area for more than 10 minutes.
Key Cancel The following key functions can be canceled by following the specified procedure.
·

Entry unlock/lock

·

Back door open

·

Prevention of key confinement

·

Warning


Key Code Registration A total of 7 electrical key transmitter sub-assemblies can be registered.



b.

Wireless Door Lock Control Function

i.

The wireless door lock control system has the following functions:

Function Outline

*: Models with power back door system

All Doors Lock Pressing the lock button of the electrical key transmitter sub-assembly locks all doors.
All Doors Unlock (2-step Unlock) Pressing the unlock button of the electrical key transmitter sub-assembly twice within 5 seconds unlocks all doors after it first unlocks the driver's door.
All Doors Unlock (1-step Unlock) Pressing the unlock button of the electrical key transmitter sub-assembly once unlocks all doors.
Power Back Door Open or Close* Pressing the power back door button for approximately 1 second opens and closes the power back door.
Answer Back When the doors are being locked or unlocked using the electrical key transmitter sub-assembly, the wireless door lock buzzer sounds and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function.
Automatic Relock If none of the doors are opened within 60 seconds after they are unlocked using the wireless door lock remote control, all the doors will be locked again automatically.
Repeat If a door is not locked in response to the locking operation of the electrical key transmitter sub-assembly, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses.
Security Sends a door lock/unlock operation request signal as a rolling code.
Door Ajar Warning If any door is open or ajar, pushing the lock button of the electrical key transmitter sub-assembly will cause the wireless door lock buzzer to sound for about 5 seconds as a warning.




DIAGNOSIS


a.

Start Function

i.

The certification ECU (smart key ECU assembly) can detect malfunctions in the entry and start system when the power source is ON.


ii.

When the ECU detects a malfunction, a message is displayed on the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.


iii.

The indicator light warning continues for 15 seconds even after the ignition switch is turned off.


iv.

The 5-digit DTCs can be read after connecting the GTS to the DLC3.


v.

The entry and start system may not operate successfully if a malfunction occurs.