Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2021.10
NM37A0E _58 Vehicle Interior _087497 HEATING / AIR CONDITIONING _0419983 AIR CONDITIONING SYSTEM CO CONTROL F

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  CONTROL  AIR CONDITIONING CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The air conditioning system consists of the following parts:

Component Function

*1: Gasoline Models

*2: HV Models

*3: Models with PTC heater

*4: Gasoline Models (LHD)

*5: Gasoline Models (RHD)

*6: Models with Automatic Air Conditioning System

Air Conditioning Control Assembly Allows operation and adjustment of the air conditioning system via switches.
No. 2 Air Conditioning Control Assembly
Air Conditioning Amplifier Assembly Transmits and receives data to and from the switches and sensors, and controls the air conditioning system.
Compressor and Magnetic Clutch*1
·

Cooler Compressor Assembly


Performs suction, compression and discharge of refrigerant gas.
HINT:

A continuously variable capacity type cooler compressor is used to steplessly control the refrigerant discharge capacity.


Compressor with Motor Assembly*2 Performs suction, compression and discharge of refrigerant gas.
HINT:

The compressor with motor assembly is driven by an electric motor.


Blower Motor with Fan Sub-assembly Controlled according to the target airflow volume calculated by the air conditioning amplifier assembly to blow air toward the cabin and circulate the air inside the cabin.
Rear Blower Motor With Fan Sub-assembly
No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
·

PTC HTR No. 1 Relay*3

·

PTC HTR No. 2 Relay*3


Supplies power to the PTC heater (quick heater assembly) according to the request from the air conditioning amplifier assembly.
PTC Heater (Quick Heater Assembly)*3 Uses electricity to heat passing ambient air.
No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Damper Servo (Front Right Side Air Outlet Mode)*2, *4 Controlled by the air conditioning amplifier assembly to move the front right side air outlet mode control damper and switch the registers.
Damper Servo (Front Side Air Outlet Mode)*5 Controlled by the air conditioning amplifier assembly to move the front side air outlet mode control damper and switch the registers.
Damper Servo (Front Right Side Air Mix) Controlled by the air conditioning amplifier assembly to move the right side air mix control damper.
Damper Servo (Front Left Side Air Mix) Controlled by the air conditioning amplifier assembly to move the left side air mix control damper.
No. 2 Air Conditioning Radiator Damper Servo Sub-assembly*2, *4 Damper Servo (Front Left Side Air Outlet Mode) Controlled by the air conditioning amplifier assembly to move the front left side air outlet mode control damper and switch the registers.
No. 1 Blower Damper Servo Sub-assembly Damper Servo (Fresh/Recirculation Damper) Driven by the air conditioning amplifier assembly to move the fresh/recirculation damper.
Rear Air Mix Damper Servo Sub-assembly Damper Servo (Rear Side Air Mix) Controlled by the air conditioning amplifier assembly to move the rear passenger seat air mix control damper.
Rear Mode Damper Servo Sub-assembly Damper Servo (Rear Side Air Outlet Mode) Controlled by the air conditioning amplifier assembly to move the rear side air outlet mode control damper and switch the registers.
Evaporator Temperature Sensor (No. 1 Cooler Thermistor) Detects the temperature of the cool air past the No. 1 cooler evaporator sub-assembly and transmits the data to the air conditioning amplifier assembly.
Rear Evaporator Temperature Sensor (No. 2 Air Conditioning Harness Assembly) Detects the temperature of the cool air past the rear evaporator sub-assembly and transmits the data to the air conditioning amplifier assembly.
Ambient Temperature Sensor (Thermistor Assembly) Detects ambient temperature and outputs it to the air conditioning amplifier assembly.
·

Room Temperature Sensor (Cooler Thermistor)*6

·

No. 2 Room Temperature Sensor (Cooler Thermistor)*6


Detects room temperature and outputs it to the air conditioning amplifier assembly.
Solar Sensor (Automatic Light Control Sensor)*6 Detects the changes in the amount of solar radiation and outputs them to the air conditioning amplifier assembly via the main body ECU (multiplex network body ECU).
Air Conditioner Pressure Sensor Detects the refrigerant pressure and outputs it to the air conditioning amplifier assembly.
ECM Receives the signals from the engine coolant temperature sensor and transmits them to the air conditioning amplifier assembly.
Hybrid Vehicle Control ECU*2
·

Sends the drive mode control signal to the air conditioning amplifier assembly.

·

Controls the compressor with motor assembly in accordance with the state of the air conditioning system and hybrid control system.


Combination Meter Assembly Transmits the vehicle speed signal to the air conditioning amplifier assembly.
Airbag Sensor Assembly Transmits the front passenger seat occupant status and front passenger seat belt buckle switch status signal to the air conditioning amplifier assembly.
Power Steering ECU (Rack and Pinion Power Steering Gear Assembly) Sends the loading control level signal to the air conditioning amplifier assembly.
Main Body ECU (Multiplex Network Body ECU)
·

Receives the signals from the solar sensor (automatic light control sensor) and transmits them to the air conditioning amplifier assembly.





SYSTEM CONTROL


a.

The automatic air conditioning system uses the following controls:

Control Outline

*1: Gasoline models

*2: HV models

*3: Models with PTC heater

*4: Models with driver seat air outlet mode

*5: Models with Automatic Air Conditioning System

Neural Network Control This control is capable of performing complex control by artificially simulating the information processing method of the nervous system of living organisms in order to establish a complex input/output relationship that is similar to a human brain.
S-FLOW Control
·

When the system judges that the rear doors have not been opened or closed while passengers are riding in the vehicle, the system automatically switches to front seat air outlet mode and begins operating according to the number of occupants and signals from each of the sensors.

·

Automatically switches to driver seat air outlet mode when the temperature inside the passenger compartment is stable while in front seat air outlet mode, or when the system judges that only the driver seat is occupied when the cooling or heating load is low.*4

HINT:

When all of the following conditions are met, the system judges that only the driver seat is occupied.

·

The passenger side door is closed

·

The front passenger side mode setting switch and front passenger temperature setting switch is not operated




Outlet Air Temperature Control
·

Based on the temperature set by the temperature control switches, the neural network control calculates the outlet air temperature based on the input signals from various sensors.

·

The temperature setting for the driver and front passenger is controlled independently in order to provide a separate vehicle interior temperature for the right and left sides of the vehicle. Thus, air conditioning control that accommodates occupant preferences has been achieved.


Blower Control Controls the blower motor in accordance with the airflow volume that has been calculated by neural network control based on the input signals from various sensors.
Air Outlet Control
·

Automatically switches the air outlets in accordance with the outlet mode that has been calculated by neural network control based on the input signals from various sensors.

·

In accordance with the engine coolant temperature, outside air temperature, amount of sunlight, required blower, outlet temperature and vehicle speed conditions, this control automatically switches the blower outlet to FOOT/DEF mode to prevent the windows from becoming fogged when the outside air temperature is low.


Air Inlet Control
·

Automatically controls the air inlet control damper to achieve the calculated outlet air temperature that is required.

·

Drives the No. 1 blower damper servo sub-assembly (fresh/recirculation damper) in accordance with the operation of the air inlet control switch and moves the dampers to the FRESH or RECIRC position.


ECO Drive Mode Control When ECO drive mode is selected, the air conditioning amplifier assembly enters ECO air conditioning mode.
Refrigerant Volume Detection Control Judges a shortage of refrigerant volume based on signals from various sensors and informs the user by turning off the indicator light of the A/C switch.
Compressor Control*1
·

The air conditioning amplifier assembly controls the compressor discharge capacity by adjusting the position of the solenoid control valve. The target discharge capacity of the compressor is calculated from signals from various sensors, including:

-

Room temperature sensor*5

-

Ambient temperature sensor

-

Evaporator temperature sensor

-

Solar sensor*5


·

Turns the air conditioning on automatically when the AUTO button is pressed when the blower is on and the air conditioning is off.


Compressor Control*2
·

The air conditioning amplifier assembly controls the compressor motor speed. The target speed of the compressor is calculated from signals from various sensors, including:

-

Room temperature sensor

-

Ambient temperature sensor

-

Evaporator temperature sensor

-

Solar sensor


·

Turns the air conditioning on automatically when the AUTO button is pressed when the blower is on and the air conditioning is off.

·

Decreases the compressor speed in order to ensure quietness when the vehicle is stopped or the engine is off.


Odor Suppression Control
·

When the air conditioning system is started, the compressor with motor assembly is operated with the blower off for approximately 6 seconds to cool the No. 1 cooler evaporator assembly. As a result, the odor inside the air conditioning unit is adsorbed in the water that forms on the surface of the evaporator.

·

From approximately 6 to 11 seconds after the system is started, the air outlet mode is set to FOOT mode and the blower operates at low speeds to discharge the air inside the air conditioning unit into the footwell. From approximately 11 to 17 seconds after the system is started, the system returns to the previously set control mode. These controls prevent the air inside the air conditioning unit from blowing out toward the face area when the air conditioning system is started, reducing feelings of discomfort.


Parking Fresh Control By automatically switching to fresh air mode when the vehicle is parked, ventilation of the parked vehicle is facilitated and outside air is introduced into the air conditioner unit assembly.
PTC Heater Control*3 When the ignition switch is turned on (IG) and the blower motor is turned on, the air conditioning amplifier assembly turns on the PTC heater (quick heater assembly) if the following conditions are met:
·

Engine coolant temperature is below the specified temperature.

·

Ambient temperature is below the specified temperature.

·

Tentative air mix damper opening angle is above the specified value (MAX HOT).




b.

Neural Network Control

i.

In the previous automatic air conditioning system, the air conditioning amplifier assembly determined the required outlet air temperature and blower air volume in accordance with a calculation formula that had been obtained based on information received from the sensors. However, because the senses of a person are rather complex, a given temperature is sensed differently depending on the environment in which the person is situated. For example, a given amount of solar radiation can feel comfortably warm in a cold climate, but extremely uncomfortable in a hot climate. Therefore, as a technique for performing a high level of control, a neural network is used in the automatic air conditioning system. With this technique, the data that has been collected under varying environmental conditions is stored in the air conditioning amplifier assembly, which effects control to provide enhanced air conditioning comfort.


ii.

The neural network control consists of neurons in an input layer, an intermediate layer, and an output layer. The input layer neurons process the input data of the ambient temperature, the amount of sunlight and the room temperature based on the signals of the switches and sensors, and output them to the intermediate layer neurons. Based on this data, the intermediate layer neurons adjust the strength of the links among the neurons. The sum of this data is then calculated by the output layer neurons in the form of the required outlet temperature, solar correction, target airflow volume and outlet mode control volume. Accordingly, the air conditioning amplifier assembly controls the servo motors and blower motor with fan sub-assembly in accordance with the control volumes that have been calculated by neural network control.

Y128416E01
2.99,0.073 4.208,0.396 1.219,0.323 10 false Intermediate Layer 3.958,0.385 5.177,0.708 1.219,0.323 10 false Output Layer 2.396,0.385 3.615,0.708 1.219,0.323 10 false Input Layer 4.594,0.74 6.354,1.094 1.76,0.354 10 false Target Output Temperature 1.188,0.74 2.948,1.094 1.76,0.354 10 false Ambient Temperature 1.323,1.406 2.677,1.781 1.354,0.375 10 false Amount of Sunlight 1.333,2.01 2.688,2.385 1.354,0.375 10 false Room Temperature 2.677,3.125 3.177,3.438 0.5,0.313 10 false Control 0.313,4.083 1.448,4.427 1.135,0.344 10 false Input Processing 2.333,3.563 3.531,3.865 1.198,0.302 10 false Neural Networking 2.49,4.104 3.333,4.521 0.844,0.417 10 false Target Outlet Temperature 0.385,5.25 1.198,5.802 0.813,0.552 10 false Temperature Setting 0.375,6.51 1.208,6.823 0.833,0.313 10 false Sensor Input 0.385,7.583 1.219,7.896 0.833,0.313 10 false Switch Input 0.594,8.458 2.698,8.771 2.104,0.313 10 false : Neural network operation range 2.313,4.896 3.5,5.344 1.188,0.448 10 false Amount of Sunlight Correction 2.479,5.698 3.344,6.271 0.865,0.573 10 false Target Airflow Volume 2.51,6.531 3.313,6.823 0.802,0.292 10 false Outlet Mode 2.583,7.281 3.24,7.563 0.656,0.281 10 false Inlet Mode 2.531,7.823 3.375,8.104 0.844,0.281 10 false Compressor 3.969,4.583 5.24,5.052 1.271,0.469 10 false Temperature Control Correction 3.865,5.708 5.365,6.208 1.5,0.5 10 false Various Types of Airflow Volume Corrections 3.906,6.427 5.344,6.938 1.438,0.51 10 false Various Types of Mode Corrections 4.063,7.167 5.135,7.698 1.073,0.531 10 false Various Types of Corrections 5.792,4.094 6.927,4.438 1.135,0.344 10 false Output Correction 5.885,4.635 6.833,5.125 0.948,0.49 10 false Air Mix Control Damper 5.917,5.833 6.813,6.135 0.896,0.302 10 false Blower Motor 5.938,6.438 6.771,6.958 0.833,0.521 10 false Mode Control Damper 5.854,7.146 6.823,7.656 0.969,0.51 10 false Air Inlet Control Damper 5.958,7.875 6.802,8.156 0.844,0.281 10 false Compressor



c.

S-FLOW Control

i.

The S-FLOW system increases air conditioner efficiency by concentrating airflow on only the occupied seats in the vehicle. When S-FLOW is on, airflow will be concentrated on the front seats, reducing the airflow and air conditioning effect on the rear seats. Additionally, when the front passenger seat is unoccupied, airflow will be concentrated on the driver's seat only. Depending on the set temperature or ambient temperature, airflow may not always be concentrated on the driver's seat only. Whenever airflow is concentrated on the driver's seat only, the temperature indicator for the front passenger side will turn off.


ii.

The following S-FLOW modes are available:

·

Automatic S-FLOW Mode

(a)

In this mode, when the rear seat is unoccupied, S-FLOW will be automatically turned on. When a rear passenger is detected, S-FLOW will be automatically turned off.

(b)

The S-FLOW indicator on the air conditioning control screen will illuminate whenever S-FLOW is on.

(c)

To override the automatic S-FLOW setting and enter manual S-FLOW mode, select the S-FLOW button on the air conditioning control screen.


·

Manual S-FLOW Mode

(a)

When the S-FLOW button is selected, S-FLOW will be manually turned on/off.

(b)

The S-FLOW indicator on the air conditioning control screen will illuminate whenever S-FLOW is on.


·

Changing from Manual S-FLOW Mode to Automatic S-FLOW Mode

(a)

Select the S-FLOW button on the air conditioning control screen to turn S-FLOW off (S-FLOW indicator is not illuminated).

(b)

Turn the ignition switch off.

(c)

After 60 minutes have elapsed, change the ignition switch to ON mode.



S-Flow Operation
Y218821E09
0.813,0.51 2.083,1.01 1.271,0.5 10 false Manual S-FLOW On (Indicator On) 5.375,0.448 6.458,1 1.083,0.552 10 false Manual S-FLOW Off (Indicator Off) 2.896,0.625 4.458,1 1.563,0.375 10 false S-FLOW switch pressed 2.958,1.625 4.5,1.948 1.542,0.323 10 false S-FLOW switch pressed 0.302,2.156 1.323,2.604 1.021,0.448 10 false S-FLOW switch pressed 6.052,1.958 7.052,2.51 1,0.552 10 false 60 minutes after ignition switch off 5.365,3.219 6.5,3.719 1.135,0.5 10 false Auto S-FLOW On (Indicator On) 3.042,4.281 4.375,4.635 1.333,0.354 10 false Rear door is opened 0.865,3.188 1.979,3.646 1.115,0.458 10 false Auto S-FLOW Off (Indicator Off) 2.594,3.5 4.802,3.823 2.208,0.323 10 false 60 minutes after ignition switch off


iii.

The system judges if a passenger is in the vehicle as follows:

·

Front Passenger Seat

(a)

The front passenger seat is judged to be occupied when the system detects an object on the front passenger seat, fastening of the front passenger seat belt, changing of the set temperature for the front passenger seat, changing of the setting for the front passenger seat seat heater system, changing of the setting for the front passenger seat climate control seat system or the opening and closing of the front passenger door. (However, when only opening and closing of the front passenger door is detected, the system will judge that the passenger seat is unoccupied after the vehicle speed reaches approximately 12 mph (20 km/h) or more.)

(b)

If the front passenger seat is judged to be occupied, the system will retain that judgment until the ignition switch is turned off.

Front Passenger Determination Method
Y231524E09
0.198,1.656 1.385,2.177 1.188,0.521 10 false No front passenger in vehicle 5.885,1.583 6.927,2.198 1.042,0.615 10 false Front passenger in vehicle 1.75,4.26 2.917,4.552 1.167,0.292 10 false Ignition switch off 3.052,5.188 4.354,5.469 1.302,0.281 10 false Ignition switch off 3.094,1.927 4.208,2.625 1.115,0.698 10 false Either front passenger or luggage in vehicle 1.594,1.969 2.927,2.615 1.333,0.646 10 false Front passenger door is opened 1.5,2.99 2.948,3.719 1.448,0.729 10 false Front passenger door is closed and speed is over 20 km/h (12 mph) 1.615,0.688 5.719,1.104 4.104,0.417 10 false Passenger seat belt is fastened, occupant detected in passenger seat, passenger temperature switch is pressed, 4.344,2.031 5.729,3.583 1.385,1.552 10 false Passenger seat belt is fastened, occupant detected in passenger seat, passenger temperature switch is pressed, 1.615,1.052 5.719,1.573 4.104,0.521 10 false changing of the setting for the front passenger seat seat heater system or changing of the setting for the front passenger seat climate control seat system 4.344,3.052 5.729,4.604 1.385,1.552 10 false changing of the setting for the front passenger seat seat heater system or changing of the setting for the front passenger seat climate control seat system


·

Rear Seats (automatic S-FLOW mode only):

(a)

The rear seat is judged to be occupied when the system detects the opening and closing of a rear door.

(b)

If a rear seat is judged to be occupied, the system will retain that judgment for 60 minutes after the ignition switch is turned off.

Rear Passenger Determination Method
Y218820E05
0.854,0.427 2,0.906 1.146,0.479 10 false No rear passenger in vehicle 2.646,0.542 4.583,0.917 1.938,0.375 10 false Rear passenger door is opened 2.625,1.406 4.667,1.76 2.042,0.354 10 false 60 minutes after power switch off 5.313,0.365 6.479,0.802 1.167,0.438 10 false Rear passenger in vehicle





d.

ECO Drive Mode Control

i.

During ECO drive mode, the air conditioning amplifier assembly restricts air conditioning system performance under specified conditions, thus improving fuel economy.


ii.

The ECO drive mode control is activated when the integration control and panel assembly (drive mode select) is operated, and then restricts air conditioning system performance as described below:

Control Outline

*: HV models

Inside/Outside Air Switch Control If the outside air temperature exceeds a certain limit, the mode switches to inside air recirculation.
Blower Level Control In AUTO mode, the blower level is lowered to the specified value and control is performed. Also, when in warm-up control, the blower level decreases.
Heater and Compressor Control* The operation of the heater or the compressor with motor assembly is decreased, to a reserved operation level.



e.

Refrigerant Volume Detection Control

i.

The air conditioning amplifier assembly judges the volume of refrigerant from the ambient temperature, refrigerant pressure and the temperature of the cool air just past the No. 1 cooler evaporator sub-assembly. When the air conditioning amplifier assembly judges that there is a refrigerant shortage, it turns off the indicator light of the A/C switch. At that time, the compressor assembly stops operating.



f.

Parking Fresh Control

i.

While parking, fresh air introduction mode is automatically selected to enhance ventilation and reduce any odor remaining in the air conditioning unit, thus odor during engine start-up is minimized.

Timing Chart (Sample)
Y167022E30
1.229,2.854 3.521,3.104 2.292,0.25 10 false : When last mode is fresh air mode 1.229,3.146 3.917,3.542 2.688,0.396 10 false : When last mode is recirculated air mode 2.188,2.302 2.854,2.656 0.667,0.354 10 false Ingintion Switch Off 2.99,2.302 3.594,2.531 0.604,0.229 10 false 1 Minute 4.458,2.313 5.156,2.698 0.698,0.385 10 false Ignition Switch ON 5.792,2.354 6.24,2.604 0.448,0.25 10 false Time 3.365,0.25 4.719,0.667 1.354,0.417 10 false Fresh air introduction while parking mode 1.688,0.365 2.51,0.615 0.823,0.25 10 false Last Mode 0.958,1.031 1.781,1.281 0.823,0.25 10 false Fresh air 0.573,1.542 2.083,1.771 1.51,0.229 10 false Recirculated air 0.094,1.25 0.865,1.479 0.771,0.229 10 false Air Inlet




DIAGNOSIS


a.

The air conditioning amplifier assembly has a self-diagnosis function. It stores any operation malfunctions in the air conditioning system or heater system in memory in the form of Diagnostic Trouble Codes (DTCs). For details, refer to the Repair Manual.