Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.10
NM37A0E _51 Engine / Hybrid System _086616 HYBRID / BATTERY CONTROL _0415276 HYBRID CONTROL SYSTEM GE GENERAL F

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The hybrid system of this hybrid vehicle employs the Toyota Hybrid System-II (THS-II) under the "Hybrid Synergy Drive" concept*.


b.

Hybrid vehicles use a combination of 2 kinds of power sources, such as an engine and HV battery, so as to take advantage of the benefits provided by each power source while compensating for each other's shortcomings. As a result, efficient operation is achieved.


c.

Hybrid vehicles do not need their batteries to be charged externally unlike existing electric-only vehicles. Therefore, special infrastructure is not required to use hybrid vehicles.


d.

Technical development of power sources (such as engines and fuel cells) is advancing in various fields. The hybrid system is a flexible system that uses a high-efficiency power unit and electric motors.


e.

Hybrid vehicles have high-voltage electrical circuits. Hybrid vehicles have been developed with consideration given to the protection of drivers and technicians against electrocution.


f.

This hybrid vehicle uses THS-II to drive the front wheels and adds the E-Four system to drive the rear wheels. (4WD/AWD models)

HINT:

*: The "Hybrid Synergy Drive" concept consists of 4 key benefits: Fuel efficiency, low emissions, seamless acceleration, and silent performance.




SPECIFICATION


a.

Motor Generator

Item Specification
MG1 MG2 MGR*

*: 4WD/AWD models

Type Permanent Magnet Motor Permanent Magnet Motor Permanent Magnet Motor
Function Generate, Engine Starter Generate, Drive Wheels Generate, Drive Wheels
Maximum System Voltage V DC 650 DC 650 DC 650
Maximum Output kW (HP) - 134 (180) 40 (54)
Maximum Torque N*m (ft.*lbf) - 270 (199) 121 (89)
Cooling System Liquid Liquid Air


b.

Inverter with Converter Assembly

Item Specification
Boost Converter Rated Voltage (Inverter Side) V DC 650
Rated Voltage (HV Battery Side) V DC 288
DC-DC Converter Rated Output Voltage V DC 11.0 to 15.5
Maximum Output Current A 150


c.

Cooling System (for Inverter with Converter Assembly and Hybrid Vehicle Transaxle Assembly)

Item Specification
Inverter Water Pump with Motor Assembly Motor Type Brushless
Discharge Volume Liter (US qts, Imp. qts) 12 (10.6, 8.8)/min. or greater
Coolant Type Toyota Genuine Super Long Life Coolant (SLLC)
Color Pink
Capacity Liter (US qts, Imp. qts) 1.9 (2.0, 1.7)
Maintenance Intervals First Time km (miles) 240000 (150000)
Subsequent km (miles) Every 80000 (50000)



MAIN FEATURES


a.

The THS-II control has the following features.

Item Outline
Idle Stop Idling of the engine is automatically stopped (idle stop) to reduce energy loss.
EV Drive
(Efficient Drive Control)
This allows the vehicle to be driven using only the electric motor when engine efficiency is low. Additionally, electricity is generated when engine efficiency is high. Control is performed to maximize the total efficiency of the vehicle.
EV Drive Mode If the driver operates the switch and the operating conditions are being met, the vehicle can run on only the electric motor.
Motor Assist The electric motor supplements the engine power when accelerating.
Regenerative Braking
(Energy Regeneration)
During deceleration and while depressing the brake pedal, part of the energy that normally would be lost as heat is collected as electrical energy to be reused, such as for motor power.


b.

The E-Four system has the following features. (4WD/AWD models)

Features Outline
Ensures Traction Performance The E-Four system achieves an appropriate level of start-off stability and acceleration on snow-covered or other slippery road surfaces.
Ensures Fuel Efficiency The E-Four system usually uses the front wheel drive only in order to ensure fuel economy. Using Motor Generator Rear (MGR), it distributes motive force to the rear wheels in accordance with driving conditions.


c.

The mechanism of the THS-II is as follows.

i.

The THS-II consists of mainly the engine, hybrid vehicle transaxle assembly, inverter with converter assembly and HV battery, and employs a series/parallel-type hybrid system. In addition, 4WD/AWD models use an E-Four system that has a combined rear drive unit (rear traction motor with transaxle assembly) and series-type hybrid system.

W142304C01
2.479,1.156 2.76,1.354 0.281,0.198 10 false *1 1.521,1.708 1.802,1.906 0.281,0.198 10 false *2 3.24,1.813 3.521,2.01 0.281,0.198 10 false *3 2.479,2.479 2.76,2.677 0.281,0.198 10 false *4 2.458,1.75 2.74,1.948 0.281,0.198 10 false *5 2.458,1.948 2.74,2.146 0.281,0.198 10 false *6 3.458,2.49 3.74,2.688 0.281,0.198 10 false *7 4.854,1.833 5.135,2.031 0.281,0.198 10 false *10 4.583,1.563 5.073,1.74 0.49,0.177 10 false *9 (*A) 4.469,2.469 4.75,2.667 0.281,0.198 10 false *8
*A 4WD/AWD Models - -
*1 Engine *2 Hybrid Vehicle Transaxle Assembly
*3 Motor Generator No. 1 (MG1) *4 Motor Generator No. 2 (MG2)
*5 Power Split Planetary Gear Unit (Compound Gear Unit) *6 Motor Speed Reduction Gear Unit (Compound Gear Unit)
*7 Inverter with Converter Assembly *8 HV Battery
*9 Rear Drive Unit (Rear Traction Motor with Transaxle Assembly) *10 Rear Motor (MGR)
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


HINT:

Generally, there are 3 types of hybrid systems: series-type hybrid system, parallel-type hybrid system and series/parallel-type hybrid system.


·

In a series-type hybrid system, the motor rotates the wheels, and the engine, using a generator, acts as an electric power source for the motor.

W101596C02
1.042,1.313 1.313,1.51 0.271,0.198 10 *1 2.01,1.313 2.281,1.51 0.271,0.198 10 *2 3.604,1.323 3.875,1.521 0.271,0.198 10 *4 3.604,0.802 3.875,1 0.271,0.198 10 *3 5.167,1.323 5.438,1.521 0.271,0.198 10 *5
*1 Engine *2 Generator
*3 Inverter *4 HV Battery
*5 Motor - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


·

In a parallel-type hybrid system, both the engine and the motor generator directly rotate the wheels. In addition to supplementing the power of the engine, the motor generator can also serve as a generator to charge the HV battery while the vehicle is in motion. Driving the vehicle only with the motor generator is also possible.

W101597C02
3.073,0.792 3.344,0.99 0.271,0.198 10 *1 3.75,0.792 4.021,0.99 0.271,0.198 10 *2 1.146,1.854 1.417,2.052 0.271,0.198 10 *3 2.333,1.875 2.604,2.073 0.271,0.198 10 *4 3.802,1.854 4.073,2.052 0.271,0.198 10 *5
*1 Engine *2 Transmission
*3 HV Battery *4 Inverter
*5 Motor Generator - -
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -


·

In a series/parallel-type hybrid system, aspects of both a series-type hybrid system and a parallel-type hybrid system are combined. The system has 2 motor generators. Electricity can be generated by motor generator No. 1 using engine power. The generated electricity is used to charge the HV battery and also to power motor generator No. 2.

W101598C02
4.906,0.667 5.177,0.865 0.271,0.198 10 *1 1.146,1.615 1.417,1.813 0.271,0.198 10 *3 2.354,1.604 2.625,1.802 0.271,0.198 10 *4 4.948,2.01 5.219,2.208 0.271,0.198 10 *6 3.813,1.24 4.083,1.438 0.271,0.198 10 *5 4.917,1.229 5.188,1.427 0.271,0.198 10 *2
*1 Engine *2 Power Split Planetary Gear Unit
*3 HV Battery *4 Inverter
*5 Motor Generator No. 1 (MG1) *6 Motor Generator No. 2 (MG2)
V100143

Electrical Power Path (DC)
V100155

Electrical Power Path (AC)
V100144

Mechanical Power Path - -




ii.

This system optimally performs cooperative control of the engine, and Motor Generator No. 1 (MG1) and Motor Generator No. 2 (MG2) in the P810 hybrid vehicle transaxle assembly that provides excellent transmission performance. On the 4WD/AWD models, the E-Four system also controls Motor Generator Rear (MGR) through the Q610 rear drive unit (rear traction motor with transaxle assembly) that provides excellent traction performance.


iii.

The system has 2 batteries, which are used for different purposes. One is the HV battery (nominal voltage of DC 288 V) which stores electrical power to drive the vehicle, and the other is the auxiliary battery (nominal voltage of DC 12 V) which supplies electrical power to the electrical components.


iv.

Furthermore, this system uses a variable-voltage system consisting of the high-output HV battery (nominal voltage of DC 288 V), a boost converter that boosts the operating voltage of MG1, MG2 and MGR* to a maximum voltage of DC 650 V, and an inverter which converts direct current and alternating current.


v.

Since hybrid vehicles are not equipped with a conventional alternator, the high-voltage from the HV battery is stepped down to approximately DC 14 V using a DC-DC converter in order to charge the auxiliary battery. Also, the HV battery regularly charges and discharges within the constant State of Charge (SOC) range while the vehicle is running. As a result, recharging from external power sources is not necessary.

*: 4WD/AWD models


W144673C01
0.094,0.188 7.083,4.385 6.99,4.198 0.104,4.521 7.094,8.719 6.99,4.198 2.073,2.708 2.208,0.896 true 1.563,6.792 0.927,5.323 true 1.906,3.323 0.75,4.01 true 4.979,3.844 4.531,2.5 true 6.552,3.396 5.198,1.75 true 2.031,7 2.135,5.104 true 1.542,2.469 0.958,1.094 true 1.938,7.646 0.719,8.292 true 4.833,8.094 4.417,6.719 true 6.677,7.365 5.25,6.042 true 6.031,8 5.042,6.813 true 0.167,0.26 0.719,0.5 0.552,0.24 12 false *A: 0.208,4.604 0.76,4.844 0.552,0.24 12 false *B: 2.135,0.677 2.573,1.052 0.438,0.375 10 false *1 0.573,4.01 0.885,4.208 0.313,0.198 10 false *3 6.594,3.448 6.906,3.646 0.313,0.198 10 false *5 4.802,8.125 5.115,8.323 0.313,0.198 10 false *4 6.042,8.042 6.354,8.24 0.313,0.198 10 false *6 6.708,7.385 7.021,7.583 0.313,0.198 10 false *5 0.833,0.896 1.271,1.271 0.438,0.375 10 false *2 2.063,4.906 2.344,5.073 0.281,0.167 10 false *1 4.969,3.896 5.281,4.094 0.313,0.198 10 false *4 0.813,5.156 1.25,5.531 0.438,0.375 10 false *2 0.552,8.302 0.865,8.5 0.313,0.198 10 false *3
*A 2WD Models *B 4WD/AWD Models
*1 Inverter with Converter Assembly
·

Inverter

·

Boost Converter

·

DC-DC Converter


*2 Engine
*3 Hybrid Vehicle Transaxle Assembly
·

Motor Generator No. 1 (MG1)

·

Motor Generator No. 2 (MG2)


*4 HV Battery
*5 Auxiliary Battery *6 Rear Drive Unit (Rear Traction Motor with Transaxle Assembly)
·

Motor Generator Rear (MGR)





vi.

A cooling system that is independent from the engine cooling system is provided to cool the inverter with converter assembly and ATF.

W144674C01
1.031,6.5 1.917,5.104 1.917,5.104 2.146,5.104 true 1.969,1.813 2.229,1.813 2.229,1.813 2.844,2.458 true 1.094,2.729 1.438,2.729 1.438,2.729 2.281,2.917 true 5.802,2.042 6.042,1.583 6.042,1.583 6.292,1.583 true 5.063,5.24 4.917,5.24 4.917,5.24 4.823,4.24 true 2.583,0.99 2.781,0.99 2.781,0.99 3.104,1.333 true 2.385,0.906 2.698,1.104 0.313,0.198 10 false *1 1.729,1.719 2.042,1.917 0.313,0.198 10 false *2 2.208,5 2.521,5.198 0.313,0.198 10 false *2 0.917,2.635 1.229,2.833 0.313,0.198 10 false *3 5.177,5.156 5.49,5.354 0.313,0.198 10 false *4 6.365,1.5 6.677,1.698 0.313,0.198 10 false *5
*1 Inverter Reserve Tank Assembly *2 Inverter Water Pump with Motor Assembly
*3 Radiator Assembly *4 Hybrid Vehicle Transaxle Assembly
·

Oil Cooler


*5 Inverter with Converter Assembly
·

Inverter

·

Boost Converter

·

DC-DC Converter


- -
V100135

HV Coolant Flow - -





PRECAUTION


a.

Hybrid Vehicle High-voltage Safety Measures

i.

High-voltage safety is comprised of 2 points: "Insulation of High-voltage Circuits" and "Cut-off of High-voltage Circuits". The hybrid system also detects whether or not a decrease in insulation resistance has occurred between the high-voltage system and body ground.



b.

Insulation of High-voltage Circuits

i.

High-voltage circuits are used between the HV battery assembly, inverter with converter assembly, hybrid transaxle, rear drive unit (rear traction motor with transaxle assembly)* and compressor with motor assembly. Each of these items is connected by a power cable and electrically insulated using cases and covers.


ii.

The power cable is also shielded using a mesh conductor built into the electrical insulation of the wires. The shielding is grounded to the chassis of the vehicle and its main purpose is to prevent electromagnetic interference.

*: 4WD/AWD models


W144675C01
0.135,0.125 7.01,3.448 6.875,3.323 0.135,3.594 7.01,6.74 6.875,3.146 1.813,1.417 1.385,0.615 1.385,0.615 1.146,0.615 true 1.802,1.76 1.177,1.76 true 1.917,2.052 1.448,2.76 1.448,2.76 1.188,2.76 false 2.052,2.156 2.052,2.865 true 4.385,2.146 4.385,2.865 true 3.583,1.51 3.583,0.656 true 1.802,4.688 1.375,3.885 1.375,3.885 1.135,3.885 true 1.792,5.031 1.167,5.031 true 1.917,5.313 1.448,6.021 1.448,6.021 1.188,6.021 false 2.104,5.469 2.104,6.177 true 4.365,5.438 4.365,6.156 true 3.573,4.76 3.573,3.906 true 4.75,4.958 5.198,3.854 5.198,3.854 5.49,3.854 false 0.219,0.188 0.531,0.385 0.313,0.198 10 false *A 0.219,3.698 0.531,3.896 0.313,0.198 10 false *B 0.948,0.531 1.26,0.729 0.313,0.198 10 false *1 0.938,1.688 1.25,1.885 0.313,0.198 10 false *2 0.938,2.698 1.25,2.896 0.313,0.198 10 false *3 1.979,2.927 2.292,3.125 0.313,0.198 10 false *4 4.302,2.917 4.615,3.115 0.313,0.198 10 false *5 3.51,0.438 3.823,0.635 0.313,0.198 10 false *6 0.917,3.802 1.229,4 0.313,0.198 10 false *1 0.917,4.948 1.229,5.146 0.313,0.198 10 false *2 0.948,5.938 1.26,6.135 0.313,0.198 10 false *3 2.01,6.271 2.323,6.469 0.313,0.198 10 false *4 4.292,6.24 4.604,6.438 0.313,0.198 10 false *5 3.479,3.708 3.792,3.906 0.313,0.198 10 false *6 5.615,3.76 5.927,3.958 0.313,0.198 10 false *7
*A 2WD Models *B 4WD/AWD Models
*1 Compressor with Motor Assembly *2 Power Cable (HV Air Conditioning Wire)
*3 Inverter with Converter Assembly *4 Hybrid Vehicle Transaxle Assembly
*5 HV Battery *6 Power Cable (HV Floor Under Wire)
*7 Rear Drive Unit (Rear Traction Motor with Transaxle Assembly) - -




c.

Cut-off of High-voltage Circuits

i.

When any of the conditions below occur, the System Main Relays (SMRs) are automatically shut off by the hybrid vehicle control ECU.

·

The ignition switch is turned off.

·

Any airbag is deployed.

·

Inverter cover is removed (interlock circuit is opened).

·

The power cable (HV floor under wire) is disconnected from the inverter with converter (interlock circuit is opened).*

·

Service plug grip handle is unlocked (interlock circuit is opened).

·

A specified malfunction occurs.

*: 4WD/AWD models



W144676E04
5.667,1.927 5.99,1.719 true 5.625,2.875 5.99,2.573 true 2.073,5.552 1.885,5.24 1.885,5.24 1.688,5.24 true 2.198,6.521 1.958,6.365 1.958,6.365 1.781,6.365 false 2.323,7.073 2.135,7.344 2.135,7.344 1.896,7.344 true 0.531,0.385 1.635,0.667 1.104,0.281 10 false Ignition Switch 0.281,0.906 1.792,1.385 1.51,0.479 10 false Certification ECU (Smart Key ECU Assembly) 0.417,2 1.677,2.385 1.26,0.385 10 false Airbag ECU (Airbag Sensor Assembly) 3.063,1.333 4.479,1.719 1.417,0.385 10 false Hybrid Vehicle Control ECU 0.844,7.26 2.146,7.635 1.302,0.375 10 false Interlock Switch 0.958,6.24 1.865,6.75 0.906,0.51 10 false Service Plug Grip 0.958,5.146 1.708,5.5 0.75,0.354 10 false HV Battery 3.458,3.927 4.104,4.198 0.646,0.271 10 false SMRB 3.458,5.01 4.104,5.281 0.646,0.271 10 false SMRP 3.458,6.188 4.104,6.458 0.646,0.271 10 false SMRG 5.031,5.667 6.698,6.188 1.667,0.521 10 false To Power Cable (HV Under Floor Wire) 5.031,4.354 6.708,4.979 1.677,0.625 10 false To Power Cable (HV Under Floor Wire) 6.052,0.646 6.927,1.063 0.875,0.417 10 false MG ECU 4.667,1.948 5.958,2.313 1.292,0.365 10 false Interlock Switch (For Inverter Cover) 4.917,7.458 6.604,7.76 1.688,0.302 10 false : CAN communication line 4.677,2.906 5.958,3.875 1.281,0.969 10 false Interlock Switch (For Power Cable (HV Floor Under Wire))*1 4.792,7 6.188,7.354 1.396,0.354 10 false *1: 4WD/AWD models