Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM37A0E _59 Vehicle Exterior _086891 MIRROR (EXT) _0416361 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Seat Position Memory System)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.

Disconnect the outer rear view mirror assembly RH connector.


ii.
B565338C01
1.885,3.167 2.052,2.667 true 1.667,3.167 1.917,2.667 true 1.896,2.354 1.646,1.854 true 1.333,2 1.646,2.198 0.313,0.198 10 false *a 1.438,1.719 1.75,1.917 0.313,0.198 10 false MV 1.813,3.167 2.125,3.365 0.313,0.198 10 false M+ 1.5,3.167 1.813,3.365 0.313,0.198 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 13 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 13 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 14 (MH)
Auxiliary battery negative (-) → Terminal 13 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 13 (M+)
Auxiliary battery negative (-) → Terminal 14 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.
B565340C01
0.802,2.354 0.719,1.854 true 0.719,3.188 0.802,2.688 true 2.802,0.052 3.115,0.208 0.313,0.156 10 false *a 2.917,0.646 3.229,0.802 0.313,0.156 10 false *b 3.031,1.219 3.344,1.375 0.313,0.156 10 false *c 2.698,1.771 3.01,1.927 0.313,0.156 10 false *d 2.354,2.292 2.667,2.448 0.313,0.156 10 false *e 0.083,1.75 0.396,1.906 0.313,0.156 10 false *f 0.5,1.667 0.813,1.865 0.313,0.198 10 false MR 0.5,3.167 0.813,3.365 0.313,0.198 10 false MF
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Seat Position Memory System)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.

Disconnect the outer rear view mirror assembly LH connector.


ii.
B565342C01
1.885,3.167 2.052,2.667 true 1.667,3.167 1.917,2.667 true 1.896,2.354 1.646,1.854 true 1.333,2 1.646,2.198 0.313,0.198 10 false *a 1.771,3.167 2.083,3.365 0.313,0.198 10 false M+ 1.521,3.167 1.833,3.365 0.313,0.198 10 false MH 1.438,1.719 1.75,1.917 0.313,0.198 10 false MV
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Auxiliary Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 13 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 13 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 14 (MH)
Auxiliary battery negative (-) → Terminal 13 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 13 (M+)
Auxiliary battery negative (-) → Terminal 14 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.
B565344C01
0.719,3.198 0.802,2.698 true 0.802,2.375 0.719,1.875 true 1.615,0.01 1.927,0.167 0.313,0.156 10 false *a 1.427,0.604 1.74,0.76 0.313,0.156 10 false *b 1.333,1.219 1.646,1.375 0.313,0.156 10 false *c 1.698,1.75 2.01,1.906 0.313,0.156 10 false *d 2,2.26 2.313,2.417 0.313,0.156 10 false *e 0.083,1.75 0.396,1.906 0.313,0.156 10 false *f 0.5,1.719 0.813,1.917 0.313,0.198 10 false MR 0.5,3.208 0.813,3.406 0.313,0.198 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 12 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 12 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Seat Position Memory System)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.

Disconnect the outer rear view mirror assembly RH connector.


ii.
B565339C01
1.583,3.208 1.833,2.875 true 1.833,2.583 1.583,2.083 true 1.854,3.208 2.021,2.875 true 1.333,2.167 1.646,2.323 0.313,0.156 10 false *a 1.417,1.917 1.729,2.115 0.313,0.198 10 false MV 1.417,3.219 1.729,3.417 0.313,0.198 10 false MH 1.75,3.219 2.063,3.417 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MV)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 1 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.
B565341C01
0.667,2.573 0.583,2.073 true 0.583,3.24 0.667,2.906 true 2.792,0.073 3.104,0.229 0.313,0.156 10 false *a 2.917,0.656 3.229,0.813 0.313,0.156 10 false *b 3.031,1.208 3.344,1.365 0.313,0.156 10 false *c 2.667,1.781 2.979,1.938 0.313,0.156 10 false *d 2.365,2.229 2.677,2.385 0.313,0.156 10 false *e 0.083,1.917 0.396,2.073 0.313,0.156 10 false *f 0.354,1.917 0.667,2.115 0.313,0.198 10 false MR 0.354,3.219 0.667,3.417 0.313,0.198 10 false MF
*a (A) Forward Position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted Position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor RH.



Hide 87940 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Seat Position Memory System)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.

Disconnect the outer rear view mirror assembly LH connector.


ii.
B565343C01
1.583,3.208 1.833,2.875 true 1.833,2.583 1.583,2.083 true 1.854,3.208 2.021,2.875 true 1.333,2.167 1.646,2.323 0.313,0.156 10 false *a 1.417,1.917 1.729,2.115 0.313,0.198 10 false MV 1.417,3.219 1.729,3.417 0.313,0.198 10 false MH 1.75,3.219 2.063,3.417 0.313,0.198 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Apply auxiliary battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1 (MV)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 1 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (MH)
Auxiliary battery negative (-) → Terminal 10 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 10 (M+)
Auxiliary battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the retractable mirror.

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.
B565345C01
0.667,2.583 0.583,2.083 true 0.583,3.219 0.667,2.885 true 1.594,0.01 1.906,0.167 0.313,0.156 10 false *a 1.5,0.604 1.813,0.76 0.313,0.156 10 false *b 1.344,1.208 1.656,1.365 0.313,0.156 10 false *c 1.677,1.719 1.99,1.875 0.313,0.156 10 false *d 2,2.188 2.313,2.344 0.313,0.156 10 false *e 0.083,1.917 0.396,2.073 0.313,0.156 10 false *f 0.333,1.917 0.646,2.115 0.313,0.198 10 false MR 0.333,3.167 0.646,3.365 0.313,0.198 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 3 (MR)
Auxiliary battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 11 (MF)
Auxiliary battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer mirror retractor LH.