Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST PIPE
RM37A0E _51 Engine / Hybrid System _086854 2GR-FKS INTAKE / EXHAUST _0416462 EXHAUST PIPE A

2GR-FKS INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 2)

Hide 89465A 2.INSTALL HEATED OXYGEN SENSOR (for Bank 1)

Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front exhaust pipe assembly.


b.

Temporarily install the front exhaust pipe assembly with 4 new nuts.


c.

Tighten the 4 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the 2 compression springs.

Standard Length 40 mm (1.57 in.)
Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front exhaust pipe assembly.


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipes when connecting them.




d.

Connect the center exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the center exhaust pipe assembly (TWC: Rear Catalyst) to the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C28
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



f.
A449083C01
2.833,0.521 3,0.396 3,0.396 2.781,0.917 true 2.344,0.76 2.677,0.76 true 3.042,0.25 3.26,0.5 0.219,0.25 10 true *b 2.115,0.656 2.313,0.927 0.198,0.271 10 true *a
*a Tube
*b Wire Harness Clamp


Connect the heated oxygen sensor (for Bank 2) connector.


g.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


h.
A454812C01
0.76,1.042 1.042,1.198 1.042,1.198 1.063,0.75 true 0.625,0.469 0.813,0.469 0.813,0.469 0.865,0.844 true 0.385,0.375 0.604,0.573 0.219,0.198 10 true *a 0.99,1.219 1.24,1.406 0.25,0.188 10 true *b
*a Tube
*b Wire Harness Clamp


Connect the heated oxygen sensor (for Bank 1) connector.


i.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


Hide 17430 5.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the 2 compression springs.

Standard Length 40 mm (1.57 in.)
Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the center exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the center exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipes when connecting them.




d.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C28
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Tail Exhaust Pipe Assembly
*2 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the tail exhaust pipe assembly and center exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 6.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform Inspection After Repair after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION