Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (EMISSION CONTROL) › EGR VALVE › 2020.02–2021.10
RM37A0E _51 Engine / Hybrid System _086908 A25A-FXS EMISSION CONTROL _0416572 EGR VALVE A

A25A-FXS EMISSION CONTROL  EGR VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 25620 1.INSTALL EGR VALVE ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Using an 8 mm socket wrench, install the EGR valve assembly to the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A453182C01
2.24,1.052 2.469,0.438 2.469,0.438 2.604,0.438 true 1.583,1.396 1.125,1.146 1.125,1.146 0.958,1.146 true 1.75,1.635 2.292,1.896 2.292,1.896 2.24,1.25 true 0.729,1.063 0.938,1.26 0.208,0.198 10 true *a 2.635,0.344 2.948,0.802 0.313,0.458 10 true *a 2.344,1.875 2.552,2.073 0.208,0.198 10 true *a
*a Claw


Install a new EGR valve gasket to the EGR valve assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.



c.
A454290C01
2.313,0.802 2.552,0.448 2.552,0.448 2.677,0.448 true 2.333,0.938 2.552,0.938 true 2.604,0.844 2.917,1.042 0.313,0.198 10 true *a 2.74,0.313 3.052,0.51 0.313,0.198 10 true *b
*a Pin
*b Hole


Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing.


d.

Using an 8 mm socket wrench, install the EGR valve assembly with the EGR valve bracket to the camshaft housing with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

for EGR Valve Bracket Connection Type:

i.

Using an 8 mm socket wrench, connect the fuel pipe sub-assembly to the EGR valve bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



f.

Connect the No. 4 water by-pass hose and No. 8 water by-pass hose to the EGR valve assembly and slide the 2 clips to secure them.


Hide 25601 2.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Install a new EGR inlet gasket to the intake manifold.


b.

Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.


c.

Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25680 3.CONNECT EGR COOLER ASSEMBLY

a.

Connect the EGR cooler assembly to the EGR valve assembly with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 4.CONNECT ENGINE WIRE

a.

Engage the 2 wire harness clamps to connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the EGR valve assembly connector.


d.
A457797C01
1.5,1.417 1.698,1 1.698,1 1.917,1 true 0.99,1.969 1.24,1.969 1.24,1.969 1.385,1.615 true 1.969,0.906 2.208,1.083 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Engage the 3 hose clamps to connect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


Hide 8.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION