Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (EMISSION CONTROL) › EGR VALVE › 2020.02–2021.10
RM37A0E _51 Engine / Hybrid System _086908 A25A-FXS EMISSION CONTROL _0416572 EGR VALVE A

A25A-FXS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT (for Engine)

Hide 2.DISCONNECT ENGINE WIRE

a.
A457797C01
1.5,1.417 1.698,1 1.698,1 1.917,1 true 0.99,1.969 1.24,1.969 1.24,1.969 1.385,1.615 true 1.969,0.906 2.208,1.083 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Disengage the 3 hose clamps and disconnect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


b.
A457798

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25680 3.DISCONNECT EGR COOLER ASSEMBLY

a.
A454284

Remove the 2 bolts and disconnect the EGR cooler assembly from the EGR valve assembly.


Hide 25601 4.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A454285

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A402226

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 5.REMOVE EGR VALVE ASSEMBLY

a.
A454286C01
2.177,1.052 2.177,0.698 true 1.333,1.479 1.031,1.479 true 2.104,1.083 2.302,1.271 0.198,0.188 10 true *1 0.781,1.417 0.969,1.604 0.188,0.188 10 true *2
*1 No. 4 Water By-pass Hose
*2 No. 8 Water By-pass Hose


Slide the 2 clips and disconnect the No. 4 water by-pass hose and No. 8 water by-pass hose from the EGR valve assembly.


b.
A454287

for EGR Valve Bracket Connection Type:

i.

Using an 8 mm socket wrench, remove the bolt and disconnect the fuel pipe sub-assembly from the EGR valve bracket.



c.
A454288

Using an 8 mm socket wrench, remove the bolt.


d.
A454289C01
2.323,0.938 2.802,0.938 true 2.333,0.813 2.594,0.563 2.594,0.563 2.771,0.563 true 2.813,0.854 3.042,1.042 0.229,0.188 10 true *a 2.813,0.479 3.031,0.688 0.219,0.208 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket from the camshaft housing vertically.


e.
A453182

Remove the EGR valve gasket from the EGR valve assembly.


f.
A402235

Using an 8 mm socket wrench, remove the bolt and EGR valve assembly from the EGR valve bracket.