Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C427158E01
0.406,1.521 3.125,1.792 2.719,0.271 10 false No. 9 Global CAN Junction Connector 0.083,1.521 2.052,1.833 1.969,0.313 10 false M96 1.563,0.5 2.229,0.74 0.667,0.24 10 false 4 1.521,1.021 1.865,1.26 0.344,0.24 10 false 10 5.646,0.5 6.333,0.75 0.688,0.25 10 false CANH 5.646,1.26 6.333,1.51 0.688,0.25 10 false CANL 5.375,0.5 6.063,0.75 0.688,0.25 10 false 32 5.375,1.031 6.063,1.281 0.688,0.25 10 false 31 1.719,1.958 3.198,2.302 1.479,0.344 10 false from Auxiliary Battery 1.74,2.74 3.135,3.042 1.396,0.302 10 false from IG2-NO. 2 Relay 3.854,1.854 5.083,2.156 1.229,0.302 10 false ECU-DCC NO. 2 4,2.604 4.802,2.823 0.802,0.219 10 false METER-IG2 5.375,1.865 6.063,2.115 0.688,0.25 10 false 40 5.646,1.979 6.333,2.229 0.688,0.25 10 false B 5.375,2.615 6.063,2.865 0.688,0.25 10 false 39 5.646,2.729 6.333,2.979 0.688,0.25 10 false IG+ 5.375,3.333 6.063,3.583 0.688,0.25 10 false 21 5.427,3.896 6.115,4.146 0.688,0.25 10 false 2 5.656,3.438 6.344,3.688 0.688,0.25 10 false ES 5.656,4.01 6.344,4.26 0.688,0.25 10 false EP 5.573,4.833 6.76,5.24 1.188,0.406 10 false Combination Meter Assembly 5.26,4.844 5.948,5.094 0.688,0.25 10 false H21

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H21 combination meter assembly connector.


c.
C427159C01
1.552,0.615 1.938,0.896 0.385,0.281 1.635,2.917 1.771,2.917 1.771,2.917 1.771,2.125 true 2.073,2.917 1.917,2.917 1.917,2.917 1.917,2.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.229,2.844 1.813,3.146 0.583,0.302 10 false CANL 1.635,0.677 2.219,0.979 0.583,0.302 10 false H21 2.146,2.833 2.729,3.135 0.583,0.302 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-32 (CANH) - H21-31 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427159C02
1.552,0.615 1.938,0.896 0.385,0.281 0.708,1.083 0.542,1.083 0.542,1.083 0.542,1.833 true 2.708,2.625 2.875,2.625 2.875,2.625 2.875,2.125 true 0.604,2.604 0.406,2.604 0.406,2.604 0.406,2.125 true 2.833,2.948 3,2.948 3,2.948 3,2.115 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.688,2.521 1.271,2.823 0.583,0.302 10 false ES 1.625,0.667 2.208,0.969 0.583,0.302 10 false H21 2.677,2.885 3.26,3.188 0.583,0.302 10 false B 0.781,1.01 1.365,1.313 0.583,0.302 10 false EP 2.448,2.542 3.031,2.844 0.583,0.302 10 false IG+
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-2 (EP) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H21-21 (ES) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
H21-40 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)