Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Certification ECU (smart key ECU assembly) branch line or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C427515E01
0.396,1.823 3.333,2.156 2.938,0.333 10 false No. 3 Global CAN Junction Connector 0.083,1.823 0.531,2.094 0.448,0.271 10 false H91 1.708,0.75 2.156,1.021 0.448,0.271 10 false 3 1.667,1.354 2.115,1.625 0.448,0.271 10 false 13 5.583,0.875 6.156,1.146 0.573,0.271 10 false CANH 5.604,1.469 6.177,1.74 0.573,0.271 10 false CANL 5.615,2.479 6.188,2.75 0.573,0.271 10 false +B 5.594,3.26 6.167,3.531 0.573,0.271 10 false E 5.375,0.74 5.823,1.01 0.448,0.271 10 false 1 5.385,1.344 5.833,1.615 0.448,0.271 10 false 2 5.396,2.375 5.844,2.646 0.448,0.271 10 false 4 5.323,3.135 5.771,3.406 0.448,0.271 10 false 18 5.521,4.042 7.042,4.594 1.521,0.552 10 false Certification ECU (Smart Key ECU Assembly) 5.208,4.042 5.656,4.313 0.448,0.271 10 false H48 4.042,2.313 4.49,2.583 0.448,0.271 10 false AM2 1.646,2.458 3.135,2.74 1.49,0.281 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.
C427160C01
1.5,0.385 1.865,0.667 0.365,0.281 1.063,1.604 1.063,0.844 1.063,0.844 1.24,0.844 true 0.917,1.594 0.917,0.833 0.917,0.833 0.75,0.833 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.573,0.448 2.104,0.813 0.531,0.365 10 false H48 0.313,0.771 0.948,0.969 0.635,0.198 10 false CANH 1.323,0.771 1.958,0.969 0.635,0.198 10 false CANL
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-1 (CANH) - H48-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427160C02
1.5,0.385 1.865,0.667 0.365,0.281 0.896,2.125 0.896,2.875 0.896,2.875 1.063,2.875 true 2.49,1.594 2.49,0.865 2.49,0.865 2.667,0.865 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.563,0.448 1.979,0.75 0.417,0.302 10 false H48 1.146,2.802 1.781,3 0.635,0.198 10 false E 2.75,0.781 3.385,0.979 0.635,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H48-18 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H48-4 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)