Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Communication stop for "Panoramic View Monitor / Circumference Monitoring Camera Control Module" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C427498E01
0.49,1.927 3.188,2.271 2.698,0.344 10 false No. 5 Global CAN Junction Connector 0.188,1.927 0.604,2.146 0.417,0.219 10 false H94 1.74,0.854 2.156,1.073 0.417,0.219 10 false 6 1.698,1.448 2.115,1.667 0.417,0.219 10 false 16 5.635,0.958 6.208,1.177 0.573,0.219 10 false CANH 5.635,1.542 6.208,1.76 0.573,0.219 10 false CANL 5.635,2.448 6.208,2.667 0.573,0.219 10 false +B 5.667,2.99 6.24,3.208 0.573,0.219 10 false IG 5.635,3.521 6.208,3.74 0.573,0.219 10 false ACC 5.635,4.104 6.208,4.323 0.573,0.219 10 false GND1 5.354,0.865 5.771,1.083 0.417,0.219 10 false 11 5.354,1.458 5.771,1.677 0.417,0.219 10 false 12 5.406,2.313 5.823,2.531 0.417,0.219 10 false 1 5.406,2.865 5.646,3.094 0.24,0.229 10 false 3 5.417,3.417 5.833,3.635 0.417,0.219 10 false 2 5.417,3.979 5.833,4.198 0.417,0.219 10 false 4 3.896,2.313 4.854,2.583 0.958,0.271 10 false ECU-B NO. 2 3.865,2.865 5.01,3.177 1.146,0.313 10 false ECU-IG1 NO. 4 4.01,3.406 4.76,3.625 0.75,0.219 10 false ECU-ACC 5.563,4.76 6.906,5.031 1.344,0.271 10 false Parking Assist ECU 5.229,4.76 5.698,5.01 0.469,0.25 10 false H20 1.635,2.448 3.188,2.719 1.552,0.271 10 false from Auxiliary Battery 2.042,3.521 3.24,3.875 1.198,0.354 10 false from ACC Relay 1.719,2.99 3.427,3.323 1.708,0.333 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H20 parking assist ECU connector.


c.
C369144C88
1.5,0.167 1.917,0.417 0.417,0.25 1.708,2.677 1.875,2.677 1.875,2.677 1.875,2.094 true 2.208,2.677 2.042,2.677 2.042,2.677 2.042,2.094 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.594,0.208 1.917,0.438 0.323,0.229 10 false H20 1.292,2.573 1.771,2.781 0.479,0.208 10 false CANH 2.292,2.594 2.771,2.802 0.479,0.208 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H20-11 (CANH) - H20-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (PARKING ASSIST ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369144C89
1.5,0.167 1.917,0.417 0.417,0.25 2.615,0.729 2.781,0.729 2.781,0.729 2.781,1.729 true 2.281,0.979 2.448,0.979 2.448,0.979 2.448,1.729 true 0.823,0.729 0.656,0.729 0.656,0.729 0.656,1.729 true 1.146,0.969 0.979,0.969 0.979,0.969 0.979,1.719 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.594,0.208 1.917,0.438 0.323,0.229 10 false H20 0.906,0.635 1.229,0.865 0.323,0.229 10 false +B 2.198,0.646 2.698,0.896 0.5,0.25 10 false GND1 2.083,0.906 2.583,1.156 0.5,0.25 10 false IG 1.219,0.885 1.625,1.135 0.406,0.25 10 false ACC
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H20-4 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-1 (+B) - Body ground Ignition switch off 11 to 14 V
H20-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V
H20-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)