Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check CAN Communication Connection  


DESCRIPTION

Symptom Trouble Area
Check CAN Communication Connection
·

CAN branch line or connector

·

Power source circuit of central gateway ECU (network gateway ECU)

·

Central gateway ECU (network gateway ECU) ground circuit

·

Central gateway ECU (network gateway ECU)

·

Power source circuit of DLC3

·

DLC3 ground circuit



WIRING DIAGRAM

C428442E01
2.125,0.313 2.583,0.51 0.458,0.198 10 false OBD 1.583,1.896 2.042,2.094 0.458,0.198 10 false DLC3 1.26,1.896 1.719,2.094 0.458,0.198 10 false H56 3.271,0.427 4.729,0.729 1.458,0.302 10 false from Auxiliary Battery 1.229,1.031 1.688,1.229 0.458,0.198 10 false BAT 1.229,1.552 1.688,1.75 0.458,0.198 10 false CG 1.646,1.031 2.104,1.229 0.458,0.198 10 false CANH 1.656,1.563 2.115,1.76 0.458,0.198 10 false CANL 1.021,1.438 1.479,1.635 0.458,0.198 10 false 4 0.969,0.906 1.427,1.104 0.458,0.198 10 false 16 2.198,0.906 2.604,1.208 0.406,0.302 10 false 6 2.167,1.458 2.573,1.76 0.406,0.302 10 false 14 5.875,0.927 6.333,1.125 0.458,0.198 10 false CA6H 6.156,1.26 6.615,1.458 0.458,0.198 10 false 60 Ω 5.865,1.677 6.323,1.875 0.458,0.198 10 false CA6L 5.604,0.927 6.01,1.229 0.406,0.302 10 false 14 5.635,1.438 6.042,1.74 0.406,0.302 10 false 5 5.896,2.188 6.354,2.385 0.458,0.198 10 false BATT 5.885,2.813 6.344,3.01 0.458,0.198 10 false ACC 5.885,3.458 6.344,3.656 0.458,0.198 10 false IG1 5.896,4.115 6.354,4.313 0.458,0.198 10 false IG2 5.875,4.635 6.333,4.833 0.458,0.198 10 false GND 5.615,4.51 6.073,4.708 0.458,0.198 10 false 10 5.656,2.073 6.063,2.375 0.406,0.302 10 false 1 5.656,2.688 6.063,2.99 0.406,0.302 10 false 2 5.594,3.354 6,3.656 0.406,0.302 10 false 11 5.594,4 6,4.302 0.406,0.302 10 false 12 4.208,3.323 5.281,3.594 1.073,0.271 10 false ECU-IG1 NO. 4 2.198,3.469 3.583,3.802 1.385,0.333 10 false from IG1-NO. 1 Relay 4.365,2.677 5.438,2.948 1.073,0.271 10 false ECU-ACC 2.5,2.813 3.646,3.083 1.146,0.271 10 false from ACC Relay 4.271,2.063 5.417,2.333 1.146,0.271 10 false ECU-B NO. 2 2.188,2.188 3.604,2.469 1.417,0.281 10 false from Auxiliary Battery 4.24,3.969 5.313,4.24 1.073,0.271 10 false ECU-IG2 NO. 3 2.208,4.115 3.625,4.448 1.417,0.333 10 false from IG2-NO. 2 Relay 5.156,5.115 7.094,5.531 1.938,0.417 10 false Central Gateway ECU (Network Gateway ECU) 4.844,5.125 5.302,5.323 0.458,0.198 10 false H59

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK GTS OPERATION
a.

Connect the GTS to the DLC3 of another vehicle.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check that the GTS and ECUs can communicate with the ignition switch ON.


HINT:
·

ECUs and sensors are not displayed on the "Communication Bus Check" screen when the GTS cannot communicate with the vehicle.

·

If communication between the GTS and ECUs is not possible, either the GTS or vehicle has a malfunction.

·

If communication between the GTS and ECUs is still not possible even when the GTS is connected to another vehicle, the GTS has a malfunction. Perform the self tests described in the GTS operator's manual. (The GTS may be malfunctioning or its battery may be discharged.)



Result:
Result Proceed to
OK (Communication between the GTS and the vehicle is not possible but communication is possible when connected to another vehicle.) A
NG (Communication is not possible between the GTS and the vehicle, nor between the GTS and another vehicle.) B



A

2.CONFIRM PROBLEM SYMPTOMS (CONFIRM ERROR ON GTS SCREEN)

B

REFER TO GTS OPERATOR'S MANUAL

2.CONFIRM PROBLEM SYMPTOMS (CONFIRM ERROR ON GTS SCREEN)
a.

Confirm error on the GTS screen.


Result:
Result Proceed to
"A communication error with Engine ECU occurred. Please confirm that Engine ECU is properly installed." is displayed. A
Cannot proceed to vehicle selection screen. B



A

3.CHECK BUS 2 MAIN LINE (CANH - CANL)

B

4.CHECK HARNESS AND CONNECTOR (DLC3 POWER SOURCE CIRCUIT)
3.CHECK BUS 2 MAIN LINE (CANH - CANL)
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C427770C11
1.625,0.198 2.094,0.448 0.469,0.25 5.052,0.177 5.469,0.448 0.417,0.271 6.156,2.125 5.99,2.125 5.99,2.125 5.99,1.646 true 1.823,1.396 1.823,2.479 1.823,2.479 1.656,2.479 true 1.917,1.396 1.917,2.479 1.917,2.479 2.083,2.479 true 4.969,0.583 5.135,0.583 5.135,0.583 5.135,1.083 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.729,0.25 2.125,0.448 0.396,0.198 10 false H59 2.167,2.396 2.719,2.594 0.552,0.198 10 false CA4L 6.25,2.052 6.802,2.25 0.552,0.198 10 false BAT 1.24,2.396 1.792,2.594 0.552,0.198 10 false CA4H 5.125,0.229 5.438,0.427 0.313,0.198 10 false H56 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 4.698,0.51 5.01,0.708 0.313,0.198 10 false CG
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition Result
H59-18 (CA4H) - H59-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
H59-18 (CA4H) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
H59-17 (CA4L) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
H59-18 (CA4H) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
H59-17 (CA4L) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK (CAN bus main lines are normal) A
NG (There is an open or short in a CAN bus main line of a suspected bus) B



A

GO TO SFI System
HINT:

Inspect the ECM supply power or VC voltage.



B

4.CHECK HARNESS AND CONNECTOR (DLC3 POWER SOURCE CIRCUIT)
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.
C428443C01
0.073,1.094 0.49,1.344 0.417,0.25 2.802,1.885 2.635,1.885 2.635,1.885 2.635,1.385 true 1.417,0.146 1.583,0.146 1.583,0.146 1.583,0.729 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *1 0.135,1.125 0.583,1.354 0.448,0.229 10 false H56 2.875,1.802 3.292,2.021 0.417,0.219 10 false BAT 1.177,0.073 1.677,0.271 0.5,0.198 10 false CG
*1 DLC3


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H56-16 (BAT) - Body ground Ignition switch off 11 to 14 V



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-4 (CG) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK OPEN IN CAN BUS LINES

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 POWER SOURCE CIRCUIT)

5.CHECK OPEN IN CAN BUS LINES
a.
C428443C02
0.073,1.094 0.49,1.344 0.417,0.25 2.281,1.885 2.115,1.885 2.115,1.885 2.115,1.385 true 2.281,0.146 2.115,0.146 2.115,0.146 2.115,0.729 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *1 0.135,1.125 0.583,1.354 0.448,0.229 10 false H56 2.365,0.073 2.865,0.271 0.5,0.198 10 false CANH 2.365,1.802 2.865,2 0.5,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-6 (CANH) - H56-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω


HINT:

If the resistance between CANH and CANL is not as specified, a connector may have been loose or disconnected during inspection. If a connector is loose or disconnected, connect it and perform the inspection again.



Result:
Result
OK
NG



OK

6.CHECK SHORT IN CAN BUS LINE

NG

8.CHECK FOR OPEN IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - DLC3)
6.CHECK SHORT IN CAN BUS LINE
a.
C428443C03
0.073,1.094 0.49,1.344 0.417,0.25 1.948,1.906 2.115,1.906 2.115,1.906 2.115,1.406 true 2.281,0.146 2.115,0.146 2.115,0.146 2.115,0.729 true 1.427,0.156 1.594,0.156 1.594,0.156 1.594,0.74 true 2.802,1.906 2.635,1.906 2.635,1.906 2.635,1.406 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *1 0.135,1.125 0.583,1.354 0.448,0.229 10 false H56 2.365,0.073 2.865,0.271 0.5,0.198 10 false CANH 1.542,1.844 2.042,2.042 0.5,0.198 10 false CANL 1.177,0.083 1.677,0.281 0.5,0.198 10 false CG 2.854,1.823 3.208,2.063 0.354,0.24 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-6 (CANH) - H56-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher
H56-6 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H56-14 (CANL) - H56-4 (CG)
H56-6 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H56-14 (CANL) - H56-16 (BAT)


HINT:

If the resistance between CANH and CANL is not as specified, a connector may have been loose or disconnected during inspection. If a connector is loose or disconnected, connect it and perform the inspection again.



Result:
Result
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

9.CHECK SHORT IN CAN BUS LINE
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H59 central gateway ECU (network gateway ECU) connector.


b.
C402518C34
1.49,0.125 1.906,0.375 0.417,0.25 0.656,0.917 0.656,0.333 0.656,0.333 0.823,0.333 true 0.49,0.917 0.49,0.167 0.49,0.167 0.656,0.167 true 0.708,1.198 0.708,1.781 0.708,1.781 0.875,1.781 true 0.542,1.208 0.542,1.958 0.542,1.958 0.708,1.958 true 2.938,0.917 2.938,0.333 2.938,0.333 2.771,0.333 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.729,0.083 1.292,0.313 0.563,0.229 10 false BATT 0.906,0.26 1.365,0.458 0.458,0.198 10 false ACC 0.781,1.875 1.24,2.073 0.458,0.198 10 false IG1 0.948,1.688 1.406,1.885 0.458,0.198 10 false IG2 1.583,0.167 2.042,0.365 0.458,0.198 10 false H59 2.427,0.26 2.885,0.458 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H59-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H59-1 (BATT) - Body ground Ignition switch off 11 to 14 V
H59-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V
H59-11 (IG1) - Body ground Ignition switch ON 11 to 14 V
H59-12 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

8.CHECK FOR OPEN IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - DLC3)
a.

Disconnect the H59 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C428444C01
0.229,0.781 0.615,1.01 0.385,0.229 3.823,0.781 4.229,1.031 0.406,0.25 1.469,1.49 1.635,1.49 1.635,1.49 1.635,0.99 true 5.917,0.167 5.75,0.167 5.75,0.167 5.75,0.583 true 1.385,0.25 1.552,0.25 1.552,0.25 1.552,0.75 true 5.927,1.563 5.76,1.563 5.76,1.563 5.76,1.146 true 3.813,0.146 4.125,0.344 0.313,0.198 10 false *1 0.344,0.052 0.656,0.25 0.313,0.198 10 false *a 0.292,0.802 0.604,1 0.313,0.198 10 false H59 3.896,0.823 4.208,1.021 0.313,0.198 10 false H56 1.073,1.417 1.573,1.656 0.5,0.24 10 false CA6H 1,0.177 1.75,0.385 0.75,0.208 10 false CA6L 6,0.104 6.615,0.427 0.615,0.323 10 false CANH 6,1.479 6.583,1.729 0.583,0.25 10 false CANL
*1 DLC3 - -
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H59-14 (CA6H) - H56-6 (CANH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H59-5 (CA6L) - H56-14 (CANL)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - DLC3)

9.CHECK SHORT IN CAN BUS LINE
a.

Disconnect the H59 central gateway ECU (network gateway ECU) connector.


b.
C428443C03
0.073,1.094 0.49,1.344 0.417,0.25 1.948,1.906 2.115,1.906 2.115,1.906 2.115,1.406 true 2.281,0.146 2.115,0.146 2.115,0.146 2.115,0.729 true 1.427,0.156 1.594,0.156 1.594,0.156 1.594,0.74 true 2.802,1.906 2.635,1.906 2.635,1.906 2.635,1.406 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *1 0.135,1.125 0.583,1.354 0.448,0.229 10 false H56 2.365,0.073 2.865,0.271 0.5,0.198 10 false CANH 1.542,1.844 2.042,2.042 0.5,0.198 10 false CANL 1.177,0.083 1.677,0.281 0.5,0.198 10 false CG 2.854,1.823 3.208,2.063 0.354,0.24 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-6 (CANH) - H56-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
H56-6 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H56-14 (CANL) - H56-4 (CG)
H56-6 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H56-14 (CANL) - H56-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))