Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Forward recognition camera branch line or connector

·

Power source circuit of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

C427520E01
5.24,4.052 7.104,4.271 1.865,0.219 10 false Forward Recognition Camera 4.979,4.052 5.365,4.302 0.385,0.25 10 false R5 1.708,0.729 2.094,0.979 0.385,0.25 10 false 3 0.521,1.833 3.135,2.104 2.615,0.271 10 false No. 5 Global CAN Junction Connector 0.135,1.833 0.521,2.083 0.385,0.25 10 false H94 1.688,1.344 2.073,1.594 0.385,0.25 10 false 13 5.604,0.875 6.146,1.125 0.542,0.25 10 false CA1P 5.594,1.458 6.135,1.708 0.542,0.25 10 false CA1N 5.604,2.469 6.146,2.719 0.542,0.25 10 false IGB 5.583,3.073 6.125,3.323 0.542,0.25 10 false GND 5.354,0.76 5.74,1.01 0.385,0.25 10 false 5 5.302,1.333 5.688,1.583 0.385,0.25 10 false 11 5.354,2.344 5.74,2.594 0.385,0.25 10 false 7 5.302,2.948 5.688,3.198 0.385,0.25 10 false 10 3.688,2.333 4.844,2.615 1.156,0.281 10 false ECU-IG1 NO. 4 1.635,2.479 3.135,2.792 1.5,0.313 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.
C325908C66
1.5,0.167 1.938,0.396 0.438,0.229 2,1.115 2,0.365 2,0.365 2.26,0.365 true 2,1.448 2,1.885 2,1.885 2.26,1.885 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.625,0.198 1.969,0.396 0.344,0.198 10 false R5 2.344,0.302 2.792,0.51 0.448,0.208 10 false CA1P 2.344,1.823 2.792,2.031 0.448,0.208 10 false CA1N
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-5 (CA1P) - R5-11 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (FORWARD RECOGNITION CAMERA)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C325908C67
1.5,0.167 1.938,0.396 0.438,0.229 1.833,1.458 1.833,1.875 1.833,1.875 2,1.875 true 1.344,1.458 1.344,1.875 1.344,1.875 1.177,1.875 true 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 1.635,0.198 1.979,0.396 0.344,0.198 10 false R5 0.927,1.813 1.375,2.021 0.448,0.208 10 false IGB 2.063,1.813 2.51,2.021 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R5-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)