Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416695 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.

·

If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.



PROCEDURE

Hide 85110R 1.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 68131 2.REMOVE BACK DOOR GLASS

NOTICE:
·

After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.

·

If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.



a.

Disconnect each connector.


b.
B565173C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the back door glass on the back door panel to prevent it from being scratched.


c.
B565175C01
0.5,0.427 0.854,0.833 true 2.979,0.542 2.583,0.833 true 1.688,1.458 1.865,1.865 false 1.063,1.823 1.625,1.135 true 3.021,0.427 3.281,0.771 0.26,0.344 10 false *1 0.313,0.333 0.615,0.615 0.302,0.281 10 false *1 1.927,1.802 2.24,1.958 0.313,0.156 10 false *a 0.885,1.813 1.167,2.021 0.281,0.208 10 false *1
*1 Back Window Glass Clip
*a Piano Wire


Pass a piano wire between the back door panel and back door glass from the exterior.


d.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


e.

Cut the adhesive by pulling the piano wire around the back door glass.

NOTICE:
·

When separating the back door glass, take care not to damage the paint or interior and exterior ornaments.

·

When cutting the adhesive, take care not to damage the connectors on the back door glass.

·

Do not pull the piano wire in a vertical direction, but pull it in a horizontal direction.

·

After cutting off the old adhesive remaining on the adhesion surface, apply new adhesive within 2 hours.

·

If the cut surface of the old adhesive is left exposed for a long time, the adhesion strength will be reduced, so apply the new adhesive quickly.




f.
B565176

Using suction cups, disengage the 3 back window glass clips and remove the back door glass.

NOTICE:
·

To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.

·

Be careful not to drop the back door glass.

·

Leave as much adhesive on the back door panel as possible when removing the back door glass.




Hide 75573C 3.REMOVE BACK WINDOW OUTSIDE MOULDING

a.

When reusing the back door glass:

i.
B594141C01
0.104,0.115 0.594,0.448 0.49,0.333 12 false *A
*A Back Side


Using a scraper, remove the back window outside moulding.

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window outside moulding with a new one.





Hide 75497B 4.REMOVE BACK WINDOW OUTSIDE MOULDING CLIP LH

a.

When reusing the back door glass:

i.

Using a scraper, remove the back window outside moulding clip LH.

B594142C01
0.198,0.167 0.771,0.542 0.573,0.375 12 false *A
*A Back Side - -


NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window outside moulding clip LH with a new one.





Hide 75496C 5.REMOVE BACK WINDOW OUTSIDE MOULDING CLIP RH

HINT:

Use the same procedure as for the LH side.


Hide 64827B 6.REMOVE BACK WINDOW GLASS CLIP

a.

When reusing the back door glass:

i.

Using a scraper, remove the back window glass clip.

B594144C01
0.198,0.167 0.771,0.542 0.573,0.375 12 false *A
*A Back Side - -


NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass clip with a new one.





Hide 62785F 7.REMOVE BACK DOOR GLASS SPACER

a.

When reusing the back door glass:

i.

Using a scraper, remove the 3 back door glass spacers.

B594146C01
0.198,0.219 0.563,0.542 0.365,0.323 12 false *A
*A Back Side - -


NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back door glass spacer with a new ones.





Hide 8.CLEAN BACK DOOR PANEL

a.

Clean and shape the contact surfaces of the back door panel.

i.
B423482C01
1.042,0.292 1.302,0.188 false 1.375,0.083 1.688,0.24 0.313,0.156 10 false *a 2.906,1.531 3.063,1.729 0.156,0.198 10 false a
*a Back Door Panel
V100155

Adhesive


Using a knife, cut off any excess adhesive on the contact surfaces of the back door panel as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.) or more


NOTICE:

Be careful not to damage the back door panel.


HINT:

Leave as much adhesive on the back door panel as possible.



ii.

Clean the contact surfaces of the back door panel with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all of the adhesive has been removed, clean the back door panel.