Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416697 WINDOW DEFOGGER SYSTEM U

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E407961C07
1.75,0.146 2.104,0.406 0.354,0.26 2.76,0.146 3.115,0.406 0.354,0.26 3.74,0.146 4.094,0.406 0.354,0.26 4.74,0.146 5.094,0.406 0.354,0.26 5.76,0.99 5.76,0.24 5.76,0.24 5.844,0.24 true 1.802,0.198 2.115,0.375 0.313,0.177 10 false H65 2.823,0.198 3.135,0.375 0.313,0.177 10 false H64 3.802,0.198 4.115,0.375 0.313,0.177 10 false H63 4.792,0.198 5.104,0.375 0.313,0.177 10 false H62 5.927,0.156 6.24,0.333 0.313,0.177 10 false *a
*a This connector is not used by the window defogger system. Refer to Air Conditioning System. - -


a.

Disconnect the H62 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-6 (IG+) - H62-17 (GND) Power source (IG) Ignition switch ON 11 to 14 V
H62-6 (IG+) - H62-17 (GND) Power source (IG) Ignition switch off Below 1 V
H62-5 (B) - H62-17 (GND) Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H62-17 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H62 air conditioning amplifier assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H63-18 (RDFG) - H62-17 (GND) Rear window defogger signal Ignition switch ON, rear window defogger switch off 11 to 14 V
H63-18 (RDFG) - H62-17 (GND) Rear window defogger signal Ignition switch ON, rear window defogger switch on Below 1 V
H62-7 (LIN1) - H62-17 (GND) LIN communication line Ignition switch ON Pulse generation



CHECK REAR WINDOW DEFOGGER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)


B567677N01
3.365,0.125 3.781,0.375 0.417,0.25 3.438,0.167 3.896,0.365 0.458,0.198 10 false H27

a.

Disconnect the H27 air conditioning control assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-6 (IG+) - H27-10 (GND) Power source (IG) Ignition switch ON 11 to 14 V
H27-6 (IG+) - H27-10 (GND) Power source (IG) Ignition switch off Below 1 V
H27-10 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H27 air conditioning control assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H27-8 (LIN1) - H27-10 (GND) LIN communication line Ignition switch ON Pulse generation