Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Door Mirror ECU RH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Door Mirror ECU RH Communication Stop Mode Communication stop for "Front Door RH/R-Mirror (FR-Door/R-Mirror)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Outer mirror control ECU assembly RH branch line or connector

·

Power source circuit of outer mirror control ECU assembly RH

·

Outer mirror control ECU assembly RH ground circuit

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

C382030E40
0.229,1.938 0.688,2.135 0.458,0.198 10 false H91 0.594,1.938 3.073,2.26 2.479,0.323 10 false No. 3 Global CAN Junction Connector 1.698,1.396 2.156,1.594 0.458,0.198 10 false 15 1.74,0.833 2.198,1.031 0.458,0.198 10 false 5 5.406,0.833 5.844,1.063 0.438,0.229 10 false 9 5.406,1.385 5.844,1.615 0.438,0.229 10 false 8 5.677,0.948 6.219,1.188 0.542,0.24 10 false CANP 5.667,1.51 6.208,1.75 0.542,0.24 10 false CANN 5.667,4.094 6.208,4.333 0.542,0.24 10 false GND 5.396,3.969 5.938,4.208 0.542,0.24 10 false 7 4.313,4.854 4.854,5.094 0.542,0.24 10 false J7 4.563,4.854 7.094,5.302 2.531,0.448 10 false Outer Mirror Control ECU Assembly RH 5.667,3.49 6.208,3.729 0.542,0.24 10 false BDR 5.667,2.906 6.208,3.146 0.542,0.24 10 false CPUB 5.667,2.313 6.208,2.552 0.542,0.24 10 false SIG 3.792,2.156 4.844,2.479 1.052,0.323 10 false ECU-IG1 NO. 4 3.979,3.333 5.396,3.656 1.417,0.323 10 false DOOR F/R 3.802,2.75 5.219,3.073 1.417,0.323 10 false ECU-DCC NO. 2 2.198,2.854 3.615,3.167 1.417,0.313 10 false from Battery 1.656,2.302 3.281,2.813 1.625,0.51 10 false from IG1-NO. 1 Relay 5.354,3.375 5.896,3.615 0.542,0.24 10 false 14 5.396,2.781 5.938,3.021 0.542,0.24 10 false 6 5.385,2.208 5.927,2.448 0.542,0.24 10 false 5 2.198,3.427 3.615,3.74 1.417,0.313 10 false from Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (OUTER MIRROR CONTROL ECU ASSEMBLY RH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the J7 outer mirror control ECU assembly RH connector.


c.
C424512C01
1.427,0.323 1.854,0.594 0.427,0.271 1.167,2.083 1.167,3 1.167,3 1.333,3 true 1.333,2.083 1.333,2.667 1.333,2.667 1.5,2.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.552,0.385 1.938,0.646 0.385,0.26 10 false J7 1.594,2.583 2.073,2.823 0.479,0.24 10 false CANP 1.417,2.927 1.896,3.167 0.479,0.24 10 false CANN
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J7-9 (CANP) - J7-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C424512C02
1.427,0.323 1.854,0.594 0.427,0.271 2.229,2.073 2.229,2.656 2.229,2.656 2.396,2.656 true 2.229,1.656 2.229,0.906 2.229,0.906 2.396,0.906 true 2.01,1.698 2.01,0.677 2.01,0.677 2.177,0.677 true 1.854,1.688 1.854,0.833 1.854,0.833 1.688,0.833 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.542,0.375 1.927,0.635 0.385,0.26 10 false J7 1.375,0.76 1.854,1 0.479,0.24 10 false SIG 2.49,2.573 2.969,2.813 0.479,0.24 10 false BDR 2.271,0.594 2.75,0.833 0.479,0.24 10 false CPUB 2.479,0.823 2.958,1.063 0.479,0.24 10 false GND
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J7-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J7-5 (SIG) - Body ground Ignition switch ON 11 to 14 V
J7-6 (CPUB) - Body ground Always 11 to 14 V
J7-14 (BDR) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)