Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM37A0E _59 Vehicle Exterior _086888 LIGHTING (EXT) _0415934 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog lights.

WIRING DIAGRAM

E436445E01
2.292,1.198 3.208,1.396 0.917,0.198 10 false J/B 2.979,1.031 3.896,1.229 0.917,0.198 10 false 4F 2.979,3.042 3.896,3.24 0.917,0.198 10 false 4D 3.01,0.823 3.927,1.021 0.917,0.198 10 false 1 2.99,2.844 3.906,3.042 0.917,0.198 10 false 21 4.615,1.698 5.531,1.896 0.917,0.198 10 false TAIL 5.313,1.552 6.229,1.75 0.917,0.198 10 false TAIL 5.865,0.917 6.781,1.115 0.917,0.198 10 false 14 6.115,0.917 7.031,1.115 0.917,0.198 10 false TRLY 5.865,3.969 6.781,4.167 0.917,0.198 10 false 27 6.115,3.969 7.031,4.167 0.917,0.198 10 false RFGO 5.51,4.854 6.427,5.052 0.917,0.198 10 false MB 5.521,5.01 7.156,5.406 1.635,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 3.302,4.438 6.031,4.698 2.729,0.26 10 false Instrument Panel Junction Block Assembly 2.146,4.469 3.063,4.667 0.917,0.198 10 false B 2.354,4.469 3.271,4.667 0.917,0.198 10 false 1 1.021,4.469 1.938,4.667 0.917,0.198 10 false 2 1.208,4.469 2.125,4.667 0.917,0.198 10 false E 1.448,4.771 2.365,4.969 0.917,0.198 10 false Fog Light 0.813,5.146 1.729,5.344 0.917,0.198 10 false V5 0.823,5.313 3.271,5.531 2.448,0.219 10 false Rear Fog Light Assembly RH 0.802,3.594 1.719,3.792 0.917,0.198 10 false V6 0.802,3.75 3.125,3.969 2.323,0.219 10 false Rear Fog Light Assembly LH 1.448,3.24 2.365,3.438 0.917,0.198 10 false Fog Light 2.146,2.927 3.063,3.125 0.917,0.198 10 false B 2.354,2.927 3.271,3.125 0.917,0.198 10 false 1 1.01,2.927 1.927,3.125 0.917,0.198 10 false 2 1.208,2.927 2.125,3.125 0.917,0.198 10 false E 0.063,1.01 1.563,1.313 1.5,0.302 10 false from Auxiliary Battery 4.49,2.427 5.406,2.625 0.917,0.198 10 false FOG RR 4.5,3.729 5.417,3.927 0.917,0.198 10 false FOG RR

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

*: w/ Door Control Battery




PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog lights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates. (Rear fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the V6 rear fog light assembly LH connector.


b.

Disconnect the V5 rear fog light assembly RH connector.


c.

Disconnect the 4D instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-1 (B) - 4D-21 Always Below 1 Ω
V5-1 (B) - 4D-21 Always Below 1 Ω
V6-1 (B) or 4D-21 - Body ground Always 10 kΩ or higher
V5-1 (B) or 4D-21 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E345461C29
1.781,0.354 2.177,0.625 0.396,0.271 3.354,2.229 3.75,2.5 0.396,0.271 5.021,0.354 5.417,0.625 0.396,0.271 2.854,3.292 3.271,2.875 false 4.365,3.281 4.781,2.865 false 1.896,0.396 2.271,0.667 0.375,0.271 10 false 4F 5.135,0.396 5.51,0.667 0.375,0.271 10 false 4D 3.448,2.26 3.823,2.531 0.375,0.271 10 false MB 2.677,3.323 3.219,3.594 0.542,0.271 10 false TRLY 4.229,3.313 4.771,3.583 0.542,0.271 10 false RFGO 0.375,0.24 0.75,0.51 0.375,0.271 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect a positive (+) lead from the auxiliary Auxiliary battery to terminal 4F-1.


c.

Connect a negative (-) lead from the auxiliary Auxiliary battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4D-21 - Auxiliary battery negative (-) terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY