Home › Vehicle Interior › HEATING / AIR CONDITIONING › REFRIGERANT LINE (for Gasoline Model)
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417360 REFRIGERANT LINE(for Gasoline Model) A

HEATING / AIR CONDITIONING  REFRIGERANT LINE(for Gasoline Model)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL PIPING CLAMP (for Suction Hose Sub-assembly Side)

a.

for Low Pressure:

i.

Remove the vinyl tape from the No. 2 air conditioner tube and accessory assembly and suction hose sub-assembly.


ii.
E399245C02
1.333,1.406 0.677,0.333 0.677,0.333 1.281,0.625 false 0.677,1.844 0.677,1.49 false 2.24,1.875 1.844,1.625 false 0.615,1.854 0.917,2.083 0.302,0.229 10 false *1 2.26,1.792 2.563,2 0.302,0.208 10 false *2 0.51,0.219 0.781,0.5 0.271,0.281 10 false *a
*1 Suction Hose Sub-assembly
*2 Piping Clamp
*a Groove


Install a new piping clamp to the suction hose sub-assembly.

NOTICE:
·

Securely engage the piping clamp to the groove of the suction hose sub-assembly.

·

Do not open the piping clamp more than the diameter of the suction hose sub-assembly when installing it.

·

Do not install the piping clamp with the large diameter section facing the wrong direction.




iii.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 12 or equivalent



iv.

Install the 2 O-rings to the suction hose sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from dirt and foreign matter.



v.
E331137C03
0.927,0.927 1.375,0.583 true 0.552,1.646 0.552,1.094 true 2.365,1.667 2.365,1.115 true 1.438,0.51 1.75,0.667 0.313,0.156 10 false *a 0.5,1.698 0.813,1.854 0.313,0.156 10 false *b 2.313,1.688 2.625,1.844 0.313,0.156 10 false *b
*a Large Diameter Section of Piping Clamp
*b Alignment Mark


Align the alignment marks and connect the suction hose sub-assembly to the No. 2 air conditioner tube and accessory assembly.

NOTICE:

Connect the parts by holding the tubes, not the piping clamp.



vi.
E331138C03
1.458,0.729 1.875,0.396 true 1.927,0.323 2.24,0.479 0.313,0.156 10 false *a
*a Large Diameter Section of Piping Clamp


Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the No. 2 air conditioner tube and accessory assembly.

NOTICE:
·

When inserting, make sure that a click sound is heard.

·

Check that the suction hose sub-assembly is securely connected by pulling it.





b.

for High Pressure:

i.

Remove the vinyl tape from the No. 2 air conditioner tube and accessory assembly and air conditioning tube assembly.


ii.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 12 or equivalent



iii.

Install the 2 O-rings to the No. 2 air conditioner tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free from dirt and foreign matter.



iv.

Connect the No. 2 air conditioner tube and accessory assembly to the air conditioning tube assembly.


v.
E273286C02
0.667,0.333 0.979,0.531 0.313,0.198 10 false *a 2.354,0.333 2.667,0.531 0.313,0.198 10 false *b 0.083,0.583 0.396,0.781 0.313,0.198 10 false *c 1.792,0.531 2.104,0.729 0.313,0.198 10 false *d
*a Correct
*b Incorrect
*c No Gap
*d Gap


Install the piping clamp to the air conditioning tube assembly.

NOTICE:

Make sure that the piping clamp is engaged securely with no gap.




Hide 2.INSTALL PIPING CLAMP (for Air Conditioning Tube Assembly Side)

Hide 3.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT