Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL MAIN VALVE › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417509 FUEL MAIN VALVE A

2GR-FKS FUEL  FUEL MAIN VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 23283B 2.REMOVE FUEL PRESSURE REGULATOR HOLDER

a.
A454401

Disengage the 2 claws and remove the fuel pressure regulator holder from the fuel suction tube with pump and gauge assembly.


Hide 23070 3.REMOVE FUEL MAIN VALVE ASSEMBLY

a.
A454402C01
2.406,0.531 2.75,0.948 2.75,0.948 2.958,0.948 true 3.042,0.865 3.375,1.281 0.333,0.417 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel suction tube with pump and gauge assembly.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-ring is firmly installed between the fuel main valve assembly and fuel suction tube with pump and gauge assembly.

·

Do not damage the fuel suction tube with pump and gauge assembly.




b.
A401697C02
1.021,0.417 1.125,0.417 1.125,0.417 1.229,0.823 false 1.563,0.688 1.698,0.292 1.698,0.292 1.813,0.292 false 0.958,1.719 1.073,1.719 1.073,1.719 1.135,1.375 false 1.865,0.208 2.177,0.365 0.313,0.156 10 false *1 0.854,0.313 1.167,0.469 0.313,0.156 10 false *a 0.792,1.625 1.104,1.781 0.313,0.156 10 false *b
*1 O-ring
*a Mesh
*b Mini-clip


Remove the O-ring from the fuel main valve assembly.

NOTICE:

Do not remove the mesh and mini-clip from the fuel main valve assembly.