Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM37A0E _53 Suspension _086867 TIRE PRESSURE MONITORING _0417517 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C361351C55
0.344,1.042 0.75,1.271 0.406,0.229 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.448,1.063 0.906,1.26 0.458,0.198 10 false M51
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the M51 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M51-1 (IG) - M51-12 (GND) IG power source Ignition switch ON 10 to 16 V
M51-7 (+B) - M51-12 (GND) Power supply (from auxiliary battery) Always 10 to 16 V
M51-9 (CANH) - M51-10 (CANL) CAN communication line Ignition switch off 54 to 69 Ω
M51-12 (GND) - Body ground Ground Always Below 1 Ω


b.

Connect the M51 tire pressure warning ECU and receiver connector.


c.

Measure the voltage according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


C427667C02
1.948,0.833 2.354,1.042 0.406,0.208 0.115,0.094 0.438,0.344 0.323,0.25 10 false *a 2.021,0.865 2.385,1.073 0.365,0.208 10 false M51
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -


Terminal No. (Symbol) Terminal Description Condition Specified Condition
M51-3 (CLSW) - M51-12 (GND) Tire pressure warning reset switch
·

Ignition switch ON

·

Steering pad switch assembly operated, "Set Pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held


Below 1.5 V
·

Ignition switch ON

·

"OK" switch (steering pad switch assembly) off


8 to 15 V
M51-4 (RDA) - M51-12 (GND) Output signals Ignition switch ON Pulse generation (see waveform 1)
M51-5 (PRG) - M51-12 (GND) Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal M51-4 (RDA) - M51-12 (GND)
M51-5 (PRG) - M51-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.