Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417558 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it, as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 85012A 2.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY

a.

Connect the windshield wiper motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.

Turn the ignition switch off.


e.

Disconnect the windshield wiper motor assembly connector.


f.

Temporarily install the front wiper crank sub-assembly to the windshield wiper motor assembly with the nut.


g.

Temporarily install the No. 1 wiper link rod to the pivot of the front wiper crank sub-assembly.


h.

Align the nut and pivot of the front wiper crank sub-assembly with the No. 1 wiper link rod as shown in the illustration.

E431048C01
2.146,0.656 2.885,1.438 true 4.927,0.719 3.896,1.823 true 4.969,0.594 5.177,0.792 0.208,0.198 10 false *a 1.948,0.542 2.26,0.698 0.313,0.156 10 false *b
*a Pivot of Front Wiper Crank Sub-assembly *b No. 1 Wiper Link Rod



i.

Tighten the nut to install the front wiper crank sub-assembly.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


j.
E431049C01
2.427,1.781 1.573,0.771 true 2.417,1.802 2.729,1.958 0.313,0.156 10 false *a
*a Pivot of Front Wiper Crank Sub-assembly


Apply MP grease to the pivot of the front wiper crank sub-assembly.


k.
E431050C01
1.354,1.156 0.792,0.979 true 1.583,0.531 2.583,1.031 true 0.604,0.865 0.917,1.021 0.313,0.156 10 false *a 1.385,0.448 1.698,0.604 0.313,0.156 10 false *b
*a No. 1 Wiper Link Rod
*b Pivot of Front Wiper Crank Sub-assembly


Connect the No. 1 wiper link rod to the pivot of the front wiper crank sub-assembly.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E431043C01
0.802,2.74 0.51,2.927 true 2.448,2.635 2.135,2.906 true 0.375,2.927 0.615,3.146 0.24,0.219 10 true *a 1.99,2.896 2.229,3.115 0.24,0.219 10 true *a 3.156,0.708 3.313,0.906 0.156,0.198 10 true 1 0.385,0.146 0.542,0.344 0.156,0.198 10 true 2
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



c.

Connect the connector.


Hide 55708 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the guide.

E435565


b.

Engage the cowl top ventilator louver sub-assembly to the windshield glass as shown in the illustration.

E431041C01
0,0 0,0 false
V113147

Install in this Direction - -


NOTICE:

Make sure to engage the guide securely, otherwise the cowl top ventilator louver sub-assembly may pop up when engaging it to the windshield glass.



c.

Engage the 3 guides and 6 claws to temporarily install the cowl top ventilator louver sub-assembly as shown in the illustration.

E431040C01
0,0 0,0 false
V113147

Install in this Direction - -


NOTICE:

Make sure that the cowl top ventilator louver sub-assembly does not contact the vehicle body, otherwise it may be damaged.



d.

Install the 2 clips.


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Engage the guide and 5 claws to install the fender to cowl side seal LH.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reusing the front wiper arm and blade assembly RH:

i.
E435446C01
1.76,1.406 2.573,1.042 true 2.646,0.927 2.958,1.083 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.
E435447C01
2.115,1.219 2.604,1.625 true 2.677,1.573 2.99,1.729 0.313,0.156 10 false *a
*a Serration


Clean the wiper pivot serrations with a wire brush.



c.

Turn the ignition switch to ON.


d.

Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.


e.

Turn the ignition switch off.


f.
E431027C01
1.604,2.792 1.99,2.594 true 0.792,2.458 0.938,2.646 0.146,0.188 10 false A 0.771,2.615 0.917,2.813 0.146,0.198 10 false A 2.031,2.479 2.281,2.677 0.25,0.198 10 true *a
*a Alignment Mark


Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10 mm (0.394 in.)



Hide 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reusing the front wiper arm and blade assembly LH:

i.
E435448C01
1.833,1.396 2.573,1.042 true 2.646,0.927 2.958,1.083 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.
E435447C01
2.115,1.219 2.604,1.625 true 2.677,1.573 2.99,1.729 0.313,0.156 10 false *a
*a Serration


Clean the wiper pivot serrations with a wire brush.



c.
E431026C01
1.302,2.823 1.656,3.104 true 0.76,2.615 0.917,2.802 0.156,0.188 10 false A 0.74,2.771 0.917,2.99 0.177,0.219 10 false A 1.698,3.021 1.938,3.229 0.24,0.208 10 true *a
*a Alignment Mark


Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10 mm (0.394 in.)



d.

Turn the ignition switch to ON.


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.


f.

Turn the ignition switch off.


g.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


Hide 85292B 9.INSTALL FRONT WIPER ARM HEAD CAP

a.
E431029

Engage the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure for the RH side and LH side.