Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM37A0E _59 Vehicle Exterior _086901 WIPER / WASHER _0417559 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E431064C01
2.01,0.479 1.688,0.75 1.688,0.75 1.427,0.479 true 1.625,0.771 1.938,0.927 0.313,0.156 10 false *a
*a Rear Wiper Motor Grommet Lip


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.
E431065C01
0.823,0.917 1.208,0.865 true 0.604,0.771 0.813,0.823 true 1.229,0.75 1.542,0.948 0.313,0.198 10 false *a 0.438,0.688 0.75,0.885 0.313,0.198 10 false *b
*a Alignment Mark
*b Ceramic Notch


Install the rear wiper motor grommet as shown in the illustration.

HINT:

Install the rear wiper motor grommet with its alignment mark facing up.



Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the clamp.


c.

Connect the connector.


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

When reusing the rear wiper arm and blade assembly:

i.
E435449C01
0.74,0.813 1.406,1.24 true 0.552,0.708 0.865,0.865 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the rear wiper motor assembly:

i.
E435450C01
2.083,1.323 2.573,1.594 true 2.625,1.552 2.938,1.708 0.313,0.156 10 false *a
*a Serration


Clean the wiper pivot serrations with a wire brush.



c.

Turn the ignition switch to ON.


d.

Operate the rear wiper motor assembly and stop it at the automatic stop position.


e.

Turn the ignition switch off.


f.
E431067C01
1.615,2.583 1.948,2.333 true 2,2.219 2.208,2.417 0.208,0.198 10 true *a 0.5,2.271 0.708,2.469 0.208,0.198 10 true A 0.49,2.542 0.698,2.74 0.208,0.198 10 true A
*a Alignment Mark


Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10.0 mm (0.394 in.)



g.

Turn the ignition switch to ON.


h.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not contact the vehicle body.


i.

Turn the ignition switch off.


j.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.
E435532C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to temporarily install the rear wiper arm head cap as shown in the illustration.


b.
E435533

Close the rear wiper arm head cap as shown in the illustration.


c.
E435534

Engage the 2 claws to install the rear wiper arm head cap as shown in the illustration.


Hide 64780A 5.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

Hide 67848E 6.INSTALL BACK DOOR SERVICE HOLE COVER LH

Hide 67847 7.INSTALL BACK DOOR SERVICE HOLE COVER RH

HINT:

Use the same procedure as for the LH side.