Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR OUTSIDE MOULDING
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417668 REAR DOOR OUTSIDE MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR OUTSIDE MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When installing the rear door outside moulding sub-assembly, heat the vehicle body using a heat light.


Standard Measurement:
Item Measurement
Vehicle Body 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install 9 new clips to the rear door outside moulding sub-assembly.


c.

Install the rear door outside moulding sub-assembly.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the release paper from the rear door outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 9 clips and attach the double-sided tape.

HINT:

Press the rear door outside moulding sub-assembly firmly to install it.



iv.

Install the nut.


v.

Install a new plug plate.


vi.

Engage the 5 claws.


vii.

Install the rear door outside moulding sub-assembly with the clip.



d.

Remove the protective tape.


Hide 75078 2.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY

HINT:

When installing the rear door lower outside moulding sub-assembly, heat the vehicle body using a heat light.


Standard Measurement:
Item Measurement
Vehicle Body 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear door lower outside moulding sub-assembly.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the release paper from the rear door lower outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 4 clips and attach the double-sided tape.

HINT:

Press the rear door lower outside moulding sub-assembly firmly to install it.



iv.

Install the rear door lower outside moulding sub-assembly with the screw and 2 clips.



c.

Remove the protective tape.