Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417669 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new roof drip side finish moulding clips, remove any double-sided tape remaining where the roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with a non-residue solvent.


a.
B362651C01
0.813,0.833 1.281,0.833 1.281,0.833 1.615,1.135 true 2.135,0.313 2.583,0.313 false 1.938,0.219 2.25,0.375 0.313,0.156 10 false *a 0.625,0.75 0.938,0.906 0.313,0.156 10 false *b
*a Adhesive
*b 2 to 3 mm Bead of Adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to each new roof drip side finish moulding clip.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.

w/o Roof Rack:

i.

Install the roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the roof drip side finish moulding clips.

B565983C01
1.198,1.042 1.198,0.365 false 0.375,1.063 0.375,0.354 0.375,0.354 1.396,0.354 false 2.177,4.406 2.177,3.698 2.177,3.698 3.198,3.698 false 3,4.406 3,3.708 false 4.271,2.99 4.271,2.667 4.271,2.667 4.5,2.667 false 1.427,0.281 1.667,0.49 0.24,0.208 10 false *a 1.844,0.427 2.083,0.635 0.24,0.208 10 false A 2.479,0.427 2.719,0.635 0.24,0.208 10 false B 3.219,3.594 3.458,3.802 0.24,0.208 10 false *a 3.719,3.792 3.958,4 0.24,0.208 10 false C 4.177,3.781 4.417,3.99 0.24,0.208 10 false D 4.531,2.563 4.771,2.771 0.24,0.208 10 false *a 5.719,2.344 5.958,2.552 0.24,0.208 10 false E 6.448,2.385 6.688,2.594 0.24,0.208 10 false F
*a Protruding Part - -


Standard Measurement:
Area Measurement Area Measurement
A 5.1 to 6.1 mm (0.0201 to 0.24 in.) B 8.6 mm (0.339 in.)
C 7.0 to 8.0 mm (0.276 to 0.315 in.) D 7.6 mm (0.299 in.)
E 5.3 to 6.3 mm (0.0209 to 0.248 in.) F 9.7 mm (0.382 in.)




c.

w/ Roof Rack:

i.

Install the roof drip side finish moulding clip to the position on the roof panel shown in the illustration. Determine the location and firmly press and install the roof drip side finish moulding clip.

B565984C01
4.281,2.25 4.281,1.896 4.281,1.896 4.573,1.896 false 4.594,1.802 4.906,2 0.313,0.198 10 false *a 5.719,1.625 6.031,1.823 0.313,0.198 10 false A 6.438,1.646 6.75,1.844 0.313,0.198 10 false B
*a Protruding Part - -


Standard Measurement:
Area Measurement Area Measurement
A 5.3 to 6.3 mm (0.0209 to 0.248 in.) B 9.7 mm (0.382 in.)




d.

Install the roof drip side finish moulding when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clip.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 24 hours




Hide 75554 2.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565980

Engage the clip and install the rear roof drip side finish moulding.


b.

Remove the protective tape.


Hide 75556C 3.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565978C01
0.844,0.385 1.844,0.385 true 1.854,0.302 2.167,0.458 0.313,0.156 10 false *a
*a Matchmark


Position the center roof drip side finish moulding by aligning it with the matchmark on the vehicle body as shown in the illustration.


b.

Engage the clip and install the center roof drip side finish moulding.


c.

Remove the protective tape.


Hide 75552 4.INSTALL FRONT ROOF DRIP SIDE FINISH MOULDING (w/o Roof Rack)

a.
B565976N01
1.083,2.188 1.24,2.385 0.156,0.198 10 false A

Engage the clip and install the front roof drip side finish moulding as shown in the illustration.

Standard Measurement:
Area Measurement
A 6.3 mm (0.248 in.)



b.

Remove the protective tape.


Hide 75597 5.INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT COVER (w/o Roof Rack)

a.
B565974C01
1.75,0.854 1.271,1.375 true 1.177,1.354 1.375,1.531 0.198,0.177 10 true *a 2.083,0.802 2.271,0.969 0.188,0.167 10 true *b
*a Mark
*b Outside of the Vehicle


Engage the 2 claws and 2 clips to install the 2 roof drip side finish moulding joint covers as shown in the illustration.


b.

Remove the protective tape.


Hide 75554 6.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING (w/ Roof Rack)

a.
B565982N01
1.042,0.156 1.198,0.354 0.156,0.198 10 false A

Engage the clip and install the rear roof drip side finish moulding as shown in the illustration.

Standard Measurement:
Area Measurement
A 11.0 mm (0.433 in.)



b.

Remove the protective tape.


Hide 63470B 7.INSTALL ROOF RACK ASSEMBLY (w/ Roof Rack)