Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Front Side)
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417670 WHEEL OPENING MOULDING(for Front Side) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front Side)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 76622C 1.REMOVE FRONT FENDER MUDGUARD

Hide 75086 2.REMOVE FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY

HINT:

When removing the front fender wheel opening moulding sub-assembly, heat the vehicle body and front fender wheel opening moulding sub-assembly using a heat light.


Heating Temperature:
Item Temperature
Front Fender Wheel Opening Moulding Sub-assembly and Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body and front fender wheel opening moulding sub-assembly excessively.


a.
B564922C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front fender wheel opening moulding sub-assembly as shown in the illustration.


b.
B564923

Remove the 5 clips.


c.
B571850

Remove the screw.


d.
B564925C01
1.031,0.927 1.323,1.094 true 1.333,1.031 1.542,1.198 0.208,0.167 10 true *1
*1 Front Fender Liner LH
V113147

Remove in this Direction


Pull back the edge of the front fender liner and disengage the 4 claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner.

·

To avoid damaging the claws, do not forcibly pull the front fender wheel opening moulding sub-assembly.




e.

Using a heat light, heat the vehicle body and front fender wheel opening moulding sub-assembly.


f.
B564926C01
1.917,2.198 2.5,1.615 true 1.781,2.198 2.01,2.375 0.229,0.177 10 true *a
*a Double-sided Tape


Disengage the 7 clips and separate the double-sided tape to remove the front fender wheel opening moulding sub-assembly.


Hide 75602A 3.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the front fender moulding sub-assembly is necessary.

·

When removing the front fender moulding sub-assembly, heat the vehicle body and front fender moulding sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Front Fender Moulding Sub-assembly and Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body and front fender moulding sub-assembly excessively.


a.
B564928C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front fender moulding sub-assembly as shown in the illustration.


b.
B564930

Remove the 2 grommets.


c.

Using a heat light, heat the vehicle body and front fender moulding sub-assembly.


d.
B564931C01
2.76,1.063 2.115,0.729 true 2.76,0.969 2.958,1.167 0.198,0.198 10 true *a
*a Double-sided Tape


Disengage the 3 clips and separate the double-sided tape to remove the front fender moulding sub-assembly.


e.

Remove the 3 clips from the front fender moulding sub-assembly.


Hide 75625C 4.REMOVE FRONT FENDER UPPER OUTSIDE MOULDING PAD

HINT:

Perform this procedure only when replacement of the front fender upper outside moulding pad is necessary.


a.
B564932

Remove the front fender upper outside moulding pad.