Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Front Side)
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417670 WHEEL OPENING MOULDING(for Front Side) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75625C 1.INSTALL FRONT FENDER UPPER OUTSIDE MOULDING PAD

HINT:
·

Perform this procedure only when replacement of the front fender upper outside moulding pad is necessary.

·

When installing the front fender upper outside moulding pad, heat the front fender moulding sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Front Fender Moulding Sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender moulding sub-assembly excessively.


a.

Clean the front fender moulding sub-assembly.

i.

Using a heat light, heat the front fender moulding sub-assembly surface.


ii.

Remove any double-sided tape from the front fender moulding sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a brush or felt, apply primer or equivalent to the front fender upper outside moulding pad installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front fender moulding sub-assembly until the primer has dried.




c.

Install a new front fender upper outside moulding pad.

i.

Using a heat light, heat the front fender moulding sub-assembly surface.


ii.

Remove the release paper from the front fender upper outside moulding pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B564933C01
0.771,0.708 0.677,1.313 0.677,1.313 0.583,0.719 true 2.906,0.729 2.771,1.323 2.771,1.323 2.625,0.75 true 0.625,0.083 0.781,0.281 0.156,0.198 10 false A 2.698,0.073 2.854,0.271 0.156,0.198 10 false B 0.604,1.333 0.917,1.531 0.313,0.198 10 false *a 2.698,1.333 3.01,1.531 0.313,0.198 10 false *a
*a Marking


Install the front fender upper outside moulding pad as shown in the illustration.

Standard Measurement:
Area Measurement
A 3.0 mm (0.118 in.)
B 5.0 mm (0.197 in.)


HINT:

Press the front fender upper outside moulding pad firmly to install it.




Hide 75602A 2.INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the front fender moulding sub-assembly is necessary.

·

When installing the front fender moulding sub-assembly, heat the vehicle body using a heat light.



Heating Temperature:
Item Temperature
Vehicle Body 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install 3 new clips to the front fender moulding sub-assembly.


c.

Install the front fender moulding sub-assembly.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the release paper from the front fender moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 3 clips and attach the double-sided tape.

HINT:

Press the front fender moulding sub-assembly firmly to install it.



iv.

Install the front fender moulding sub-assembly with the 2 grommets.



d.

Remove the protective tape.


Hide 75086 3.INSTALL FRONT FENDER WHEEL OPENING MOULDING SUB-ASSEMBLY

HINT:

When installing the front fender wheel opening moulding sub-assembly, heat the vehicle body using a heat light.


Heating Temperature:
Item Temperature
Vehicle Body 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove any double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front fender wheel opening moulding sub-assembly.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the release paper from the front fender wheel opening moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Engage the 7 clips and attach the double-sided tape.

HINT:

Press the front fender wheel opening moulding sub-assembly firmly to install it.



iv.
B564927C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws as shown in the illustration.


v.

Install the screw.


vi.

Install the front fender wheel opening moulding sub-assembly with the 5 clips.



c.

Remove the protective tape.


Hide 76622C 4.INSTALL FRONT FENDER MUDGUARD