Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417675 BLACK OUT TAPE A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

·

Forward recognition camera

·

Windshield glass*


Adjust forward recognition camera
·

Dynamic Radar Cruise Control System (for HV model)

·

Front Camera System

·

Lane Control System

·

Road Sign Assist System

·

Pre-collision System

·

Lighting System (EXT)


One Time Recognition:
(Click here)
or
Sequential Recognition:
(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system, lighting system(EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

·

Forward recognition camera

·

Windshield glass*


Adjust forward recognition camera
·

Dynamic Radar Cruise Control System (for Gasoline model)

·

Front Camera System

·

Lane Control System

·

Road Sign Assist System

·

Pre-collision System

·

Lighting System (EXT)


One Time Recognition:
(Click here)
or
Sequential Recognition:
(Click here)

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system, lighting system(EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75534 1.REMOVE WINDSHIELD OUTSIDE MOULDING

Hide 75928B 2.REMOVE NO. 4 BLACK OUT TAPE

HINT:

When removing the No. 4 black out tape, heat the vehicle body and No. 4 black out tape using a heat light.


Heating Temperature:
Item Temperature
No. 4 Black Out Tape and Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body and No. 4 black out tape excessively.


a.

Using a heat light, heat the vehicle body and No. 4 black out tape.


b.
B563594

Pull back on one of the ends of the No. 4 black out tape to remove it.

HINT:

When pulling on the No. 4 black out tape, pull it parallel to the vehicle body.