Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417738 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B520311N41
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.042,1.479 2.354,1.677 0.313,0.198 10 false H43 2.042,1.802 2.354,2 0.313,0.198 10 false H44 0.865,1.073 1.177,1.271 0.313,0.198 10 false 4D 0.865,1.656 1.177,1.854 0.313,0.198 10 false 4C 0.875,2.021 1.188,2.219 0.313,0.198 10 false 4E 0.896,2.25 1.208,2.448 0.313,0.198 10 false 4F 5.844,1.146 6.156,1.344 0.313,0.198 10 false 4B 5.844,1.76 6.156,1.958 0.313,0.198 10 false 4A 1.229,3.281 1.542,3.479 0.313,0.198 10 false H44 3.25,3.25 3.563,3.448 0.313,0.198 10 false H43 5.531,3.24 5.844,3.438 0.313,0.198 10 false H42 1.833,4.604 2.146,4.802 0.313,0.198 10 false 4A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 4C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 4D 5.427,6.219 5.74,6.417 0.313,0.198 10 false 4F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 4E 5.51,4.604 5.823,4.802 0.313,0.198 10 false 4B

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H42-19 (GND2) - Body ground Ground Always Below 1 Ω


c.

Reconnect the instrument panel junction block assembly connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
MB-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
MB-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

*1: for HV Model

*2: for Gasoline Model



e.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


f.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-17 (LSWR) - Body ground Rear door RH unlock detection switch input Rear door RH unlocked → Rear door RH locked Below 1 V → 11 to 14 V
H43-1 (FLCY) - Body ground Front door courtesy light switch (for LH) input Front door LH open → closed Below 1 V → 11 to 14 V
H43-6 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH open → closed Below 1 V → 11 to 14 V
4D-24 (LCTY) - Body ground Rear door courtesy light switch (for LH) input Rear door LH open → closed Below 1 V → 11 to 14 V
4A-31 (RCTY) - Body ground Rear door courtesy light switch (for RH) input Rear door RH open → closed Below 1 V → 11 to 14 V
4D-34 (BCTY) - Body ground Back door courtesy light switch input Back door open → closed Below 1 V → 11 to 14 V
4B-13 (LSFL) - Body ground Front door LH unlock detection switch input Front door LH unlocked → locked Below 1 V → 11 to 14 V
4B-12 (LSFR) - Body ground Front door RH unlock detection switch input Front door RH unlocked → locked Below 1 V → 11 to 14 V
4B-14 (LSWL) - Body ground Rear door LH unlock detection switch input Rear door LH unlocked → Rear door LH locked Below 1 V → 11 to 14 V
4D-8 (ACT-) - Body ground Door lock motor unlock drive output Door control switch or driver door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4D-9 (ACT-) - Body ground Door lock motor unlock drive output Door control switch or driver door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4D-6 (ACT+) - Body ground Door lock motor lock drive output Door control switch or driver door key cylinder off → on (lock) Below 1 V → 11 to 14 V → Below 1 V
4B-4 (ACTD) - Body ground Door lock motor unlock drive output Door control switch or driver door key cylinder off → on (unlock) Below 1 V → 11 to 14 V → Below 1 V
4D-20 (TR+) - Body ground*1 Back door lock motor unlock drive output Back door opener switch off → on Below 1 V → 11 to 14 V → Below 1 V
H44-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder in neutral position → on (unlock) 11 to 14 V → Below 1 V
H44-18 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder in neutral position → on (lock) 11 to 14 V → Below 1 V
4A-7 (GSW) - Body ground Airbag sensor signal (collision detection signal) Ignition switch ON with airbag sensor assembly connector disconnected 4.3 to 5.5 V
H43-9 (ACTG) - Body ground*2 Collision door lock release signal Collision door lock release function does not operate Below 2 V*3
7.3 to 9.9 V*4
Collision door lock release function operates Below 1 V

*1: w/o Power Back Door System

*2: w/ Door Control Battery

*3: Door control battery not charged

*4: Door control battery charging or charged




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B506743C04
3.25,0.458 3.646,0.698 0.396,0.24 2.063,0.458 2.458,0.698 0.396,0.24 4.552,0.458 4.948,0.698 0.396,0.24 2.146,0.51 2.604,0.708 0.458,0.198 10 false A19 2.51,0.49 2.823,0.688 0.313,0.198 10 false *A 3.354,0.49 3.667,0.688 0.313,0.198 10 false M5 4.625,0.49 5.083,0.688 0.458,0.198 10 false H48
*A for Gasoline Model - -


a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-4 (+B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H48-18 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H48 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M5-26 (TSW5) - Body ground Back door opener switch input Back door opener switch (open switch) off → on Below 1 Ω → pulse generation