DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start, Main Body, Master Switch or Back Door* / Data List.
*: w/ Power Back Door System
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Ignition switch ACC signal | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ACC |
- |
| IG SW | Ignition switch ON signal | OFF or ON | OFF: Ignition switch off or ACC
ON: Ignition switch ON |
- |
| RR Door Courtesy SW | Rear door courtesy light switch (for RH) signal | OFF or ON | OFF: Rear door RH closed
ON: Rear door RH open |
- |
| RL Door Courtesy SW | Rear door courtesy light switch (for LH) signal | OFF or ON | OFF: Rear door LH closed
ON: Rear door LH open |
- |
| Back Door Courtesy SW | Back door courtesy switch signal | OFF or ON | OFF: Back door closed
ON: Back door open |
- |
| Back Door Open | Back door lock signal | Prohibt or Permit | Prohibt: Back door locked
Permit: Back door unlocked |
- |
| Door Key SW-Lock | Driver door key-linked lock / unlock switch lock signal | OFF or ON | OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position |
- |
| D Door Key SW-UL | Driver door key-linked lock / unlock switch unlock signal | OFF or ON | OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position |
- |
| FR Door Lock Pos | Front door RH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door RH locked
UNLOCK: Front door RH unlocked |
- |
| FR Door Courtesy SW | Front door courtesy light switch (for RH) signal | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Lock Pos | Front door LH unlock detection switch signal | LOCK or UNLOCK | LOCK: Front door LH locked
UNLOCK: Front door LH unlocked |
- |
| FL Door Courtesy SW | Front door courtesy light switch (for LH) signal | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
| RR-Door Lock Pos SW | Rear door RH unlock detection switch signal | OFF or ON | OFF: Rear door RH locked
ON: Rear door RH unlocked |
- |
| RL-Door Lock Pos SW | Rear door LH unlock detection switch signal | OFF or ON | OFF: Rear door LH locked
ON: Rear door LH unlocked |
- |
| Unlock Key Twice | Key-linked 2-step unlock function | OFF or ON | Customize setting displayed | - |
| Auto Lock | Speed-sensitive automatic door lock function | OFF or ON | Customize setting displayed | - |
| Auto Lock/Shift | Shift-linked automatic door lock function | OFF or ON | Customize setting displayed | - |
| Auto Unlock/Shift | Shift-linked automatic door unlock function | OFF or ON | Customize setting displayed | - |
| All Unlock/Open-Close | Driver door-linked automatic door unlock function | OFF or ON | Customize setting displayed | - |
| The Number of DTC | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Switch Status | Multiplex network master switch assembly lock signal | OFF or ON | OFF: Lock switch of multiplex network master switch assembly not pushed
ON: Lock switch of multiplex network master switch assembly pushed |
- |
| Door Unlock Switch Status | Multiplex network master switch assembly unlock signal | OFF or ON | OFF: Unlock switch of multiplex network master switch assembly not pushed
ON: Unlock switch of multiplex network master switch assembly pushed |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Courtesy SW | Back door courtesy switch signal* | OFF or ON | OFF: Back door closed
ON: Back door open |
- |
*: w/ Power Back Door System
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch (open switch) | OFF or ON | OFF: Back door opener switch (open switch) not pressed
ON: Back door opener switch (open switch) pressed |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Door Lock | Door lock motor | OFF/Unlock/Lock | - |
| D-Door Unlock | Driver door lock motor | OFF/ON | - |
| Trunk and Back-Door Open | Back door lock motor* | OFF/ON | - |
| Shock Detection Unlock | Operate door lock motor | UNLOCK/LOCK | - |
*: w/o Power Back Door System