Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417738 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

HINT:

If DTC B1243 is stored, the automatic door lock function, and collision door lock release function will be prohibited.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Wire harness or connector



WIRING DIAGRAM

B345030E85
1.25,0.938 1.708,1.135 0.458,0.198 10 false GSW 5.406,0.844 5.719,1.042 0.313,0.198 10 false 24 0.573,1.813 1.031,2.01 0.458,0.198 10 false H58 0.573,1.969 2.313,2.354 1.74,0.385 10 false Airbag Sensor Assembly 5.646,0.938 6.104,1.135 0.458,0.198 10 false GSW 4.427,0.823 4.74,1.021 0.313,0.198 10 false 7 1.667,0.833 1.979,1.031 0.313,0.198 10 false 25 3.938,1.281 4.25,1.479 0.313,0.198 10 false 4A 3.948,1.427 5.552,2.031 1.604,0.604 10 false Instrument Panel Junction Block Assembly 5.302,1.885 5.615,2.083 0.313,0.198 10 false MB 5.302,2.031 6.927,2.479 1.625,0.448 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

OK:

DTC B1243 is not output.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (GSW VOLTAGE)
2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (GSW VOLTAGE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

Turning the ignition switch to ON with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the H58 airbag sensor assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
B508271C17
1.458,0.229 1.875,0.479 0.417,0.25 1.74,3.104 2.021,3.104 2.021,3.104 2.021,2.021 false 1.531,0.26 1.99,0.458 0.458,0.198 10 false H58 1.344,3.031 1.802,3.229 0.458,0.198 10 false GSW 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H58-25 (GSW) - Body ground Ignition switch ON 4.3 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE AIRBAG SENSOR ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

OK:

DTC B1243 is not output.


Result:
Proceed to
OK
NG



OK

END (AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H58-25 (GSW) - 4A-7 Always Below 1 Ω
4A-7 or H58-25 (GSW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU).

B472423C19
1.917,1 2.333,1.25 0.417,0.25 5.417,0.667 5.833,0.917 0.417,0.25 3.26,2.156 3.01,2.156 3.01,2.156 3.01,1.573 true 5.531,0.698 5.844,0.896 0.313,0.198 10 false 4A 2.01,1.031 2.323,1.229 0.313,0.198 10 false MB 3.323,2.073 3.781,2.271 0.458,0.198 10 false GSW 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-24 (GSW) - 4A-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY