Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417745 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

a.

Check the operation of the door lock motor.

i.

Move the door lock to the lock position.

B563708C01
5.5,2.552 5.135,2.552 5.135,2.552 5.135,1.938 true 5.604,2.333 5.323,2.333 5.323,2.333 5.323,1.948 true 4.729,2.323 4.99,2.323 4.99,2.323 4.99,1.938 true 4.625,1.385 4.938,1.542 0.313,0.156 10 false *a 0.833,0.99 1.177,1.25 0.344,0.26 10 false *b 0.833,2.813 1.146,3.167 0.313,0.354 10 false *c 5.677,2.25 6.292,2.448 0.615,0.198 10 false ACT+ 4.5,2.24 4.813,2.438 0.313,0.198 10 false D+ 5.563,2.469 6.177,2.667 0.615,0.198 10 false ACT-
*a Component without harness connected
(Back Door Lock Assembly)
*b Lock
*c Unlock - -



ii.

Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) → 1 (ACT+)
Auxiliary battery negative (-) → 2 (ACT-)
Unlocks


If the result is not as specified, replace the back door lock assembly.



b.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ACT-) - 3 (D+) Locked 10 kΩ or higher
2 (ACT-) - 3 (D+) Unlocked Below 1 Ω


If the result is not as specified, replace the back door lock assembly.



Hide 69350P 2.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/ Power Back Door)

a.
B563709C01
1.042,0.542 1.313,0.542 1.313,0.542 1.781,1.104 true 0.833,0.781 1.052,0.781 1.052,0.781 1.385,1.177 true 1.042,4.198 1.042,4.49 1.042,4.49 1.25,4.49 true 0.75,4.198 0.75,4.49 0.75,4.49 0.531,4.49 true 0.896,3.135 0.906,2.563 0.906,2.563 0.74,2.563 true 1.021,3.135 1.021,2.823 1.021,2.823 1.323,2.823 true 0.771,3.135 0.771,2.823 0.771,2.823 0.521,2.823 true 0.427,3.313 0.719,3.313 true 1.063,3.313 1.365,3.313 true 0.833,0.448 1,0.667 0.167,0.219 10 false *a 0.646,0.688 0.823,0.896 0.177,0.208 10 false *b 2.979,3.125 3.292,3.281 0.313,0.156 10 false *c 2.719,3.104 2.896,3.271 0.177,0.167 10 false *d 2.156,3.26 2.375,3.438 0.219,0.177 10 false *e 1.823,3.792 1.969,3.979 0.146,0.188 10 false *f 0.073,2.479 0.385,2.76 0.313,0.281 10 false *g 0.083,3.594 0.396,3.875 0.313,0.281 10 false *g 0.302,4.396 0.615,4.594 0.313,0.198 10 false M+ 1.292,4.406 1.604,4.604 0.313,0.198 10 false M- 0.385,2.74 0.542,2.927 0.156,0.188 10 false E 0.365,2.479 0.896,2.698 0.531,0.219 10 false FSW 1.385,2.74 1.708,2.938 0.323,0.198 10 false CLS 0.146,3.219 0.469,3.417 0.323,0.198 10 false CTY 1.406,3.229 1.729,3.427 0.323,0.198 10 false OPN
*a Clockwise
*b Counterclockwise
*c Over-latch
*d Full-latch
*e Half-latch
*f Open-latch
*g Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)


Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Battery Connection Result
Auxiliary battery positive (+) → 2 (M+)
Auxiliary battery negative (-) → 1 (M-)
Latch turns to full-latch position (rotates counterclockwise)
Auxiliary battery positive (+) → 1 (M-)
Auxiliary battery negative (-) → 2 (M+)
Latch turns to open-latch position (rotates clockwise)


If the result is not as specified, replace the back door lock assembly with courtesy light switch.


b.

Check the operation of the latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CLS) - 1 (E) Full-latch 10 kΩ or higher
3 (CLS) - 1 (E) Half-latch 10 kΩ or higher
3 (CLS) - 1 (E) Half-latch → Open-latch 10 kΩ or higher → Below 1 Ω
3 (CLS) - 1 (E) Open-latch Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition
3 (CLS) - 1 (E) Open-latch Below 1 Ω
3 (CLS) - 1 (E) Open-latch → Half-latch Below 1 Ω → 10 kΩ or higher
3 (CLS) - 1 (E) Half-latch 10 kΩ or higher
3 (CLS) - 1 (E) Full-latch 10 kΩ or higher
3 (CLS) - 1 (E) Over-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



c.

Check the operation of the pawl switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW) - 1 (E) Open-latch 10 kΩ or higher
2 (FSW) - 1 (E) Open-latch → Half-latch 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch 10 kΩ or higher
2 (FSW) - 1 (E) Half-latch → Full-latch 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
2 (FSW) - 1 (E) Full-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



d.

Check the operation of the back door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (CTY) - 1 (E) Open-latch Below 1 Ω
4 (CTY) - 1 (E) Half-latch Below 1 Ω
4 (CTY) - 1 (E) Half-latch → Full-latch Below 1 Ω → 10 kΩ or higher
4 (CTY) - 1 (E) Full-latch 10 kΩ or higher
4 (CTY) - 1 (E) Over-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



e.

Check the operation of the selector switch.

i.
B567065C01
2.375,2.458 2.146,2.458 2.146,2.458 1.365,1.677 true 1.313,1.302 0.563,0.552 0.563,0.552 0.333,0.552 true 0.958,3.802 1.479,3.802 true 2.292,4.458 1.938,4.458 1.938,4.458 1.927,4.042 true 0.156,0.458 0.344,0.625 0.188,0.167 10 false *a 2.417,2.365 2.729,2.521 0.313,0.156 10 false *b 0.677,2.938 1,3.208 0.323,0.271 10 false *c 2.354,4.385 2.969,4.615 0.615,0.229 10 false OPN 0.823,3.729 1.021,3.979 0.198,0.25 10 false E
*a Selector Switch
*b Selector Gear
*c Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (OPN) - 1 (E) Selector Switch ON Below 1 Ω
6 (OPN) - 1 (E) Selector Switch OFF 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly with courtesy light switch.